CutMaster True Service Manual - Victor Technologies - Europe

More documents

Recommendations

Info

CUTMASTER 25mm 3.04 Gas Connections Connecting Gas Supply to Unit The connection is the same for compressed air or high pressure cylinders. Refer to the following two subsections if an optional air line filter is to be installed. 1. Connect the air line to the inlet port. The illustration shows typical fittings as an example. NOTE For a secure seal, apply thread sealant to the fitting threads, according to manufacturer's instructions. Do not use Teflon tape as a thread sealer, as small particles of the tape may break off and block the small air passages in the torch. Hose Clamp Gas Supply Hose Art # A-07943 Regulator/Filter Assembly Air Connection to Inlet Port Inlet Port 1/4 NPT or ISO-R to 1/4” (6mm) Fitting INSTALLATION 3-4 <strong>Manual</strong> 0-5081
Installing Optional Single - Stage Air Filter CUTMASTER 25mm An optional filter kit is recommended for improved filtering with compressed air, to keep moisture and debris out of the torch. 1. Attach the Single - Stage Filter Hose to the Inlet Port. 2. Attach the Filter Assembly to the filter hose. 3. Connect the air line to the Filter. The illustration shows typical fittings as an example. NOTE For a secure seal, apply thread sealant to the fitting threads, according to the maker's instructions. Do Not use Teflon tape as a thread sealer, as small particles of the tape may break off and block the small air passages in the torch. Connect as follows: Hose Clamp Gas Supply Hose Regulator/Filter Assembly 1/4 NPT to 1/4" (6mm) Fitting Optional Single - Stage Filter Installation Inlet Port Art # A-07944 <strong>Manual</strong> 0-5081 3-5 INSTALLATION
Page 1 and 2: 25mm CUTMASTER PLASMA CUTTING SYST
Page 3 and 4: ! WARNINGS Read and understand this
Page 5 and 6: TABLE OF CONTENTS SECTION 1:GENERAL
Page 7 and 8: TABLE OF CONTENTS APPENDIX 1: SEQUE
Page 9 and 10: SECTION 1: GENERAL INFORMATION 1.01
Page 11 and 12: 14. American Welding Society Standa
Page 13 and 14: 1.06 Documents De Reference Consult
Page 15 and 16: 1.08 Statement of Warranty CUTMASTE
Page 17 and 18: SECTION 2 SYSTEM: INTRODUCTION 2.01
Page 19 and 20: 2.05 Input Wiring Specifications 3
Page 21 and 22: SECTION 2 TORCH: INTRODUCTION 2T.01
Page 23 and 24: B. Gas Distribution The single gas
Page 25 and 26: 3.01 Unpacking SECTION 3 SYSTEM: IN
Page 27: For CE units: EMC Input Power Filte
Page 31 and 32: SECTION 3 TORCH: INSTALLATION 3T.01
Page 33 and 34: SECTION 4 SYSTEM: OPERATION 4.01 Fr
Page 35 and 36: STANDOFF CutMaster 25mm Gas Pressur
Page 37 and 38: SECTION 4 TORCH: OPERATION 4T.01 To
Page 39 and 40: Torch Standoff Improper standoff (t
Page 41 and 42: Shield Cup With Straight Edge The d
Page 43 and 44: 4T.05 Gouging ! WARNINGS Be sure th
Page 45 and 46: 4T.07 Parts Selection for Manual an
Page 47 and 48: CUTMASTER 25mm Type Torch: SL60 Wit
Page 49 and 50: CUTMASTER 25mm Type Torch: SL60 wit
Page 55 and 56: Catalog # Description Patent(s) 9-8
Page 57 and 58: 5.01 General Maintenance SECTION 5
Page 59 and 60: 5.04 Fault Indicator At initial pow
Page 61 and 62: Problem - Symptom Possible Cause Re
Page 63 and 64: 5. Remove the fitting from the filt
Page 65 and 66: B. Cover Installation 1. Reverse pr
Page 67 and 68: 9. Close torch switch (Pendant swit
Page 69 and 70: 3. Open or improperly connected rib
Page 71 and 72: L. AC LED on, TEMP, GAS, DC LED's a
Page 73 and 74: 4. Shorted Torch a) Disconnect torc
Page 75 and 76: 5.12 Test Procedures A. Main Contac
Page 77 and 78: Signal Information Many of the sign
Page 79 and 80:
B. CAPACITOR PCB TEST POINTS MTH1,2
Page 81 and 82:
CUTMASTER 25mm Signal Source/Destin
Page 83 and 84:
This Page Intentionally Blank CUTMA
Page 85 and 86:
J3-1 N/A J3-2 Common J4-1 3.3VDc J4
Page 87 and 88:
SECTION 5 TORCH: SERVICE 5T.01 Gene
Page 89 and 90:
6.01 Introduction A. Parts List Bre
Page 91 and 92:
6.05 Front Panel Replacement Parts
Page 93 and 94:
6.07 Right Side Replacement Parts C
Page 95 and 96:
6.09 Replacement Parts for Hand Tor
Page 97 and 98:
1 2 3 12 4 10 10 11 5 9 CUTMASTER 2
Page 99 and 100:
SECTION 7: REPLACEMENT PROCEDURES 7
Page 101 and 102:
7.05 Front Panel Parts Replacement
Page 103 and 104:
13. Remove the two screws securing
Page 105 and 106:
7.08 Right Side Internal Parts Repl
Page 107 and 108:
ACTION: Close external disconnect s
Page 109 and 110:
APPENDIX 3: TORCH PIN - OUT DIAGRAM
Page 111 and 112:
C. Automation Torch Connection Diag
Page 113 and 114:
CUTMASTER 25MM Manual 0-5081 A-7 AP
Page 115 and 116:
GLOBAL CUSTOMER SERVICE CONTACT The
show all

CutMaster True Service Manual - Victor Technologies - Europe

Create successful ePaper yourself

Delete template?

Save as template?