- Page 1 and 2:
25mm CUTMASTER PLASMA CUTTING SYST
- Page 3 and 4:
! WARNINGS Read and understand this
- Page 5 and 6:
TABLE OF CONTENTS SECTION 1:GENERAL
- Page 7 and 8:
TABLE OF CONTENTS APPENDIX 1: SEQUE
- Page 9 and 10:
SECTION 1: GENERAL INFORMATION 1.01
- Page 11 and 12:
14. American Welding Society Standa
- Page 13 and 14:
1.06 Documents De Reference Consult
- Page 15 and 16:
1.08 Statement of Warranty CUTMASTE
- Page 17 and 18:
SECTION 2 SYSTEM: INTRODUCTION 2.01
- Page 19 and 20:
2.05 Input Wiring Specifications 3
- Page 21 and 22:
SECTION 2 TORCH: INTRODUCTION 2T.01
- Page 23 and 24:
B. Gas Distribution The single gas
- Page 25 and 26:
3.01 Unpacking SECTION 3 SYSTEM: IN
- Page 27 and 28:
For CE units: EMC Input Power Filte
- Page 29 and 30:
Installing Optional Single - Stage
- Page 31 and 32:
SECTION 3 TORCH: INSTALLATION 3T.01
- Page 33 and 34:
SECTION 4 SYSTEM: OPERATION 4.01 Fr
- Page 35 and 36:
STANDOFF CutMaster 25mm Gas Pressur
- Page 37 and 38:
SECTION 4 TORCH: OPERATION 4T.01 To
- Page 39 and 40:
Torch Standoff Improper standoff (t
- Page 41 and 42:
Shield Cup With Straight Edge The d
- Page 43 and 44:
4T.05 Gouging ! WARNINGS Be sure th
- Page 45 and 46:
4T.07 Parts Selection for Manual an
- Page 47 and 48:
CUTMASTER 25mm Type Torch: SL60 Wit
- Page 49 and 50:
CUTMASTER 25mm Type Torch: SL60 wit
- Page 51 and 52:
CUTMASTER 25mm Type Torch: SL60 Wit
- Page 53 and 54:
CUTMASTER 25mm Type Torch: SL60 Wit
- Page 55 and 56:
Catalog # Description Patent(s) 9-8
- Page 57 and 58:
5.01 General Maintenance SECTION 5
- Page 59 and 60:
5.04 Fault Indicator At initial pow
- Page 61 and 62: Problem - Symptom Possible Cause Re
- Page 63 and 64: 5. Remove the fitting from the filt
- Page 65 and 66: B. Cover Installation 1. Reverse pr
- Page 67 and 68: 9. Close torch switch (Pendant swit
- Page 69 and 70: 3. Open or improperly connected rib
- Page 71 and 72: L. AC LED on, TEMP, GAS, DC LED's a
- Page 73 and 74: 4. Shorted Torch a) Disconnect torc
- Page 75 and 76: 5.12 Test Procedures A. Main Contac
- Page 77 and 78: Signal Information Many of the sign
- Page 79 and 80: B. CAPACITOR PCB TEST POINTS MTH1,2
- Page 81 and 82: CUTMASTER 25mm Signal Source/Destin
- Page 83 and 84: This Page Intentionally Blank CUTMA
- Page 85 and 86: J3-1 N/A J3-2 Common J4-1 3.3VDc J4
- Page 87 and 88: SECTION 5 TORCH: SERVICE 5T.01 Gene
- Page 89 and 90: 6.01 Introduction A. Parts List Bre
- Page 91 and 92: 6.05 Front Panel Replacement Parts
- Page 93 and 94: 6.07 Right Side Replacement Parts C
- Page 95 and 96: 6.09 Replacement Parts for Hand Tor
- Page 97 and 98: 1 2 3 12 4 10 10 11 5 9 CUTMASTER 2
- Page 99 and 100: SECTION 7: REPLACEMENT PROCEDURES 7
- Page 101 and 102: 7.05 Front Panel Parts Replacement
- Page 103 and 104: 13. Remove the two screws securing
- Page 105 and 106: 7.08 Right Side Internal Parts Repl
- Page 107 and 108: ACTION: Close external disconnect s
- Page 109 and 110: APPENDIX 3: TORCH PIN - OUT DIAGRAM
- Page 111: C. Automation Torch Connection Diag
- Page 115 and 116: GLOBAL CUSTOMER SERVICE CONTACT The