upgrading and repairing PCs technicians ... - 400 Bad Request
upgrading and repairing PCs technicians ... - 400 Bad Request upgrading and repairing PCs technicians ... - 400 Bad Request
12 Chapter 12 Operating System Installation and Diagnostic Testing This chapter covers methods for testing and diagnosing systems and the software you’ll use. For hardware tools, see Chapter 13, “Tools and Techniques.” Installing an Operating System on an Empty Drive Use this section for a quick reference for the procedures you’ll follow and software you’ll need to install an operating system. Installing MS-DOS Prerequisites: Create a bootable disk (containing COMMAND.COM and hidden files). The boot disk also should contain FDISK, FORMAT, SYS, and MSD, along with Help, Qbasic, and Edit files. Create the bootable disk with FORMAT A:/S on a system with the same MS-DOS version. Then, copy files from the \DOS folder. Follow these steps: 1. Boot the system with the bootable disk. 2. Run FDISK and create the partition(s) desired. The drive must have an active (which will be C: and bootable) partition; it can also have an extended partition (D: and beyond) that can contain one or more drives. 3. Exit FDISK. 4. Reboot the computer with the bootable disk. 5. Run FORMAT to format drive(s) created with FDISK: FORMAT C:/S formats & copies system files to C: FORMAT D: formats D: drive if present; repeat for E: & others 6. Remove the bootable floppy and restart the system from the C: drive. 7. Install the remainder of the operating system files from the disk or other storage device (install drivers first if necessary).
- Page 43 and 44: Memory, Resolution, and Color Depth
- Page 45 and 46: Local-Bus Video Standards 249 Deter
- Page 47 and 48: Table 10.18 AGP Support by Chipset
- Page 49 and 50: Setting Up Multiple Monitor Support
- Page 51 and 52: Setting Up Multiple Monitor Support
- Page 53 and 54: Troubleshooting Video Capture Devic
- Page 55 and 56: Troubleshooting Video Capture Devic
- Page 57 and 58: Audio I/O Connectors 261 connector
- Page 59 and 60: Configuring Sound Cards 263 • Dig
- Page 61 and 62: Troubleshooting Audio Hardware 265
- Page 63 and 64: • Bus mouse adapter cards • Ser
- Page 65: Troubleshooting Audio Hardware 269
- Page 68 and 69: 272 Table 11.1 Comparing Client/Ser
- Page 70 and 71: 274 Chapter 11—Networking • Win
- Page 72 and 73: 276 Chapter 11—Networking Selecti
- Page 74 and 75: 278 Chapter 11—Networking Etherne
- Page 76 and 77: 280 10. Repeat steps 4—9 for the
- Page 78 and 79: 282 Chapter 11—Networking The adv
- Page 80 and 81: 284 Chapter 11—Networking Wireles
- Page 82 and 83: 286 Table 11.14 TCP/IP Protocol Set
- Page 84 and 85: 288 Chapter 11—Networking Trouble
- Page 86 and 87: 290 Chapter 11—Networking Table 1
- Page 88 and 89: 292 Chapter 11—Networking capabil
- Page 90 and 91: 294 Chapter 11—Networking Enter t
- Page 92 and 93: 296 Chapter 11—Networking • If
- Page 96 and 97: 300 Installing Windows 9x Prerequis
- Page 98 and 99: 302 2. Put the Windows NT 4.0 or Wi
- Page 100 and 101: 304 Note Use the same procedure for
- Page 102 and 103: 306 Chapter 12—Operating System I
- Page 105 and 106: 1 Chapter 13 13 0789724545 ch13 9/2
- Page 107 and 108: 13 0789724545 ch13 9/22/00 Table 13
- Page 109 and 110: 13 0789724545 ch13 9/22/00 Table 13
- Page 111 and 112: 13 0789724545 ch13 9/22/00 Table 13
- Page 113 and 114: 14 Serial Ports and Cables Chapter
- Page 115 and 116: HD68m HD68f Serial Ports and Cables
- Page 117 and 118: Video Connectors Video Ports Pin 1
- Page 119 and 120: Sound Card Ports Sound Card Externa
- Page 121 and 122: Sound Card Internal Connectors Netw
- Page 123: BNC connector Network and Modem Por
- Page 126 and 127: 330 addresses addresses I/O (serial
- Page 128 and 129: 332 BIOS configuration worksheet, 8
- Page 130 and 131: 334 client/server networking client
- Page 132 and 133: 336 connectors IEE-1394, 320 intern
- Page 134 and 135: 338 devices devices 4-wire (IEEE-13
- Page 136 and 137: 340 drives comparing ribbon cables
- Page 138 and 139: 342 Fast Page-Mode RAM (FPM DRAM) F
- Page 140 and 141: 344 host adapters IEEE-1394, 210 PC
- Page 142 and 143: 346 internal pin-type connectors, 2
12<br />
Chapter 12<br />
Operating System<br />
Installation <strong>and</strong><br />
Diagnostic Testing<br />
This chapter covers methods for testing <strong>and</strong> diagnosing systems<br />
<strong>and</strong> the software you’ll use. For hardware tools, see Chapter 13,<br />
“Tools <strong>and</strong> Techniques.”<br />
Installing an Operating System on<br />
an Empty Drive<br />
Use this section for a quick reference for the procedures you’ll follow<br />
<strong>and</strong> software you’ll need to install an operating system.<br />
Installing MS-DOS<br />
Prerequisites:<br />
Create a bootable disk (containing COMMAND.COM <strong>and</strong> hidden<br />
files). The boot disk also should contain FDISK, FORMAT, SYS, <strong>and</strong><br />
MSD, along with Help, Qbasic, <strong>and</strong> Edit files. Create the bootable<br />
disk with FORMAT A:/S on a system with the same MS-DOS version.<br />
Then, copy files from the \DOS folder.<br />
Follow these steps:<br />
1. Boot the system with the bootable disk.<br />
2. Run FDISK <strong>and</strong> create the partition(s) desired. The drive must<br />
have an active (which will be C: <strong>and</strong> bootable) partition; it<br />
can also have an extended partition (D: <strong>and</strong> beyond) that<br />
can contain one or more drives.<br />
3. Exit FDISK.<br />
4. Reboot the computer with the bootable disk.<br />
5. Run FORMAT to format drive(s) created with FDISK:<br />
FORMAT C:/S formats & copies system files to C:<br />
FORMAT D: formats D: drive if present; repeat for<br />
E: & others<br />
6. Remove the bootable floppy <strong>and</strong> restart the system from the<br />
C: drive.<br />
7. Install the remainder of the operating system files from the<br />
disk or other storage device (install drivers first if necessary).