9560 Transaction Manager User's Manual - Intermec

More documents

Recommendations

Info

$\AIT\AIT-IV Cognex DM7500 Quick Reference$

9560 Transaction Manager User’s Manual 6-16 Standard Display Prompts The following table lists the configuration prompts and options for the standard 2x40 character display. The options are the same for each display, but the prompts are different. The prompts are listed in the order they appear. Configuration Prompts for 2x40 Standard Display Prompt Options Comments FOR HELP START SELECT CODES NO CODE 39 NO CHK DIGIT FULL ASCII C39 DISABLED I 2/5 VARIABLE UPC A / EAN-13 ENABLED UPC VERSION E ENABLED EAN-8 ENABLED SUPPLEMENTALS ENABLED CODABAR STANDARD START / STOP ABCD S/S CODE 11 1 CHECK DIGIT CODE 93 ENABLED NO YES NO CHK DIGIT WITH CHK DIGIT HIBC DISABLED DISABLED ENABLED VARIABLE CASECODE FIXED LENGTH DISABLED ENABLED UPC A ONLY DISABLED ENABLED DISABLED ENABLED DISABLED ENABLED DISABLED STANDARD CONCATENATED DISABLED ABC ABCD S/S DC1-DC4 S/S DISABLE S/S 1 CHECK DIGIT 2 CHECK DIGIT DISABLE ENABLED DISABLED Type ? to view help prompts, or press Enter to configure. Selecting No skips the following options and displays the OP PARAMETERS prompt. Fixed length requires an even-numbered length.
Configuration Prompts for 2x40 Standard Display (continued) CODE 128 STANDARD STANDARD UCC-128 DISABLED Configuring the 9560 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA OP PARAMETERS NO BEEP VOLUME X DISPLAY MODE BUFFERED CHARACTER SET US-ASCII CRRM DISABLED PREAMBLE A REQD NO SCANNER TIMEOUT 0 SECONDS SCANNER MODE 1 SHOT TRIGGER MODE LEVEL APPEND TIME NO TIME IN SECONDS NO RESUME IRL PROG NO SELECT PROTOCOL NO (PT. TO PT.) NO YES 6 Selecting No skips the following options and displays the SELECT PROTOCOL prompt. 0 THROUGH 7 Press Space to select a number from 0 through 7 for X. BUFFERED TRANSPARENT US-ASCII FRENCH GERMAN UNITED KINGDOM DANISH SWEDISH ITALIAN SPANISH KATAKANA DISABLED ENABLED NO YES 1 SHOT AUTOMATIC LEVEL EDGE NO YES NO YES NO YES If you choose Katakana, you also specify Kana or Ro-maji entry style and select a function key to switch between US-ACII and Katakana. Type a number from 0 through 60 msec. AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA SELECT PROTOCOL USER DEFINED NO (PT. TO PT.) NO (USER DEFINED) NO (POLLING D) NO (MULTI-DROP) NO (U.D.M-DROP) USER DEFINED POINT TO POINT POLLING MODE D MULTI-DROP USER D. M-DROP This prompt displays the currently selected protocol. Press Space to view the protocol options. The following prompts and options are displayed if needed for the protocol you choose here. 6-17
Page 1 and 2:
nugget code39 helconital User’s M
Page 3:
nugget code39 helconital Manual Cha
Page 6 and 7:
9560 Transaction Manager User’s M
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 15 and 16:
Before You Begin nugget code39 helc
Page 17 and 18:
nugget code39 helconital fBefore Yo
Page 19 and 20:
This Convention Means nugget code39
Page 21 and 22:
nugget code39 helconital A B C D E
Page 23 and 24:
Roadmap For Help With Start Here nu
Page 25 and 26:
nugget code39 helconital Getting St
Page 27:
nugget code39 helconital Getting St
Page 30 and 31:
nugget code39 helconital
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 63 and 64:
Page 65 and 66:
Starting the 9560 Operating the 956
Page 67 and 68:
Reading Bar Code Labels Operating t
Page 69 and 70:
Using the Magnetic Card Reader Oper
Page 71 and 72: Operating the 9560 4 4. Practice us
Page 73 and 74: Using the Keypad The 9560 has three
Page 75 and 76: nugget code39 helconital A B C D E
Page 77 and 78: Data Communications and Operating O
Page 95 and 96: ASCII Chart Data Communications and
Page 97 and 98: ASCII Control Characters Data Commu
Page 99 and 100: Entering Katakana Characters Data C
Page 101 and 102: Katakana Characters in Roman Alphab
Page 103 and 104: Special Katakana Characters in Japa
Page 107 and 108: nugget code39 helconital A B C D E
Page 109 and 110: Configuring the 9560 This chapter e
Page 111 and 112: Operating Parameters Configuration
Page 113 and 114: Communications Protocol Configurati
Page 115 and 116: Configuring the 9560 User-Defined a
Page 117 and 118: Downloading Configuration Commands
Page 119 and 120: Configuring the 9560 6 Moving Aroun
Page 121: SELECT CODES NO 3. Press Space. The
Page 125 and 126: Configuration Prompts for 2x40 Stan
Page 127 and 128: Configuration Prompts for 1x20 Disp
Page 129 and 130: Configuration Prompts for 1x20 Disp
Page 131: Configuration Prompts for 1x20 Disp
Page 135 and 136: Configuration Commands This chapter
Page 137 and 138: AFF (Affirmative Acknowledgment) Co
Page 139 and 140: Baud Rate Configuration Commands -
Page 141 and 142: Character Set Configuration Command
Page 143 and 144: Or: To use Codabar Standard, scan o
Page 145 and 146: Code 39 Configuration Commands - Co
Page 147 and 148: Code 128 Configuration Commands - C
Page 149 and 150: Data Bits Configuration Commands -
Page 151 and 152: EOM (End of Message) Configuration
Page 153 and 154: Intercharacter Delay Configuration
Page 155 and 156: Interleaved 2 of 5 (I 2 of 5) Confi
Page 157 and 158: IRL END (End of Program) Configurat
Page 159 and 160: IRL EOP (End of Program Block) Conf
Page 161 and 162: IRL PAK (Program Acknowledge) Confi
Page 163 and 164: IRL RUN Configuration Commands - IR
Page 165 and 166: Katakana Configuration Commands - K
Page 167 and 168: Configuration Commands - Katakana K
Page 169 and 170: NEG (Negative Acknowledgment) Confi
Page 171 and 172: POL (Poll) Purpose: Solicits or req
Page 173 and 174:
Protocol Configuration Commands - P
Page 175 and 176:
REQ (Request for Acknowledgment) Co
Page 177 and 178:
Resume IRL Configuration Commands -
Page 179 and 180:
Scanner Operation Configuration Com
Page 181 and 182:
Select Terminal Mode Configuration
Page 183 and 184:
Stop Bits Purpose: Sets the number
Page 185 and 186:
Time in Seconds Purpose: Determines
Page 187 and 188:
Turnaround Delay Configuration Comm
Page 189 and 190:
UPC/EAN Configuration Commands - UP
Page 191 and 192:
6. Scan this label: Exit Configurat
Page 193:
XON Configuration Commands - XON Pu
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Data Entry Commands - Clear Clear P
Page 202 and 203:
Data Entry Commands - Default Confi
Page 204 and 205:
Data Entry Commands - Enable Clock
Page 206 and 207:
Data Entry Commands - Enter Compute
Page 208 and 209:
Data Entry Commands - Enter IRL Edi
Page 210 and 211:
Data Entry Commands - Exit Auto-Tri
Page 212 and 213:
Data Entry Commands - Exit Full ASC
Page 214 and 215:
Data Entry Commands - High Beep Hig
Page 216 and 217:
Data Entry Commands - LED/Relay Con
Page 218 and 219:
Data Entry Commands - Low Beep Low
Page 220 and 221:
Data Entry Commands - Preamble B Pr
Page 222 and 223:
Data Entry Commands - Reset Reset P
Page 224 and 225:
Data Entry Commands - Run Program R
Page 227 and 228:
Page 229 and 230:
Introduction to IRL Interactive Rea
Page 231 and 232:
Exiting from Command Line Mode Inte
Page 233 and 234:
Interactive Reader Language To exit
Page 235 and 236:
Unique IRL Commands for the 9560 In
Page 237 and 238:
Interactive Reader Language W2 :Lea
Page 239 and 240:
Interactive Reader Language G#0=0.S
Page 241 and 242:
Program Listing #3 Controlling the
Page 243 and 244:
Magnetic Card Reader Commands Inter
Page 245:
Card Reader Responses to Host Comma
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 255 and 256:
Page 257 and 258:
Specifications A This appendix list
Page 259 and 260:
Hardware Interfaces Port Interface
Page 261:
Input Devices Compatible With the 9
Page 265 and 266:
ASCII Bar Code Labels Full ASCII Ch
Page 267 and 268:
Symbols ! * /A* * /A* , (comma) * /
Page 269 and 270:
Uppercase Letters A * A* * A* B * B
Page 271:
A B C D E Caps F G H I J $ K L M N
Page 274 and 275:
Page 276 and 277:
Page 279:
A B C D E Caps F G H I J $ K L M N
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 299 and 300:
Index Numbers 1700 keyboard, 1-6, 6
Page 301 and 302:
command, data entry continued Enter
Page 303 and 304:
G getting started, 1-3 glossary, G-
Page 305 and 306:
output relays, continued descriptio
Page 307:
Transmit File command, 8-31 Transmi
show all

9560 Transaction Manager User's Manual - Intermec

Create successful ePaper yourself

Delete template?

Save as template?