CutMaster 700 - Posch

More documents

Recommendations

Info

Troubleshooting 46 Conveyor belt jerks or does not move Conveyor belt jerks or does not move Not enough hydraulic oil in hydraulic system Poor quality hydraulic oil Check hydraulic oil level See [➙ 29] Change hydraulic oil See [➙ 37] Conveyor belt too slack Tension conveyor belt See [➙ 22]
12 Technical data Type Z Z E11 Drive Drive type PTO PTO Electric motor Output kW 15 15 11 Voltage V - - 400 Fusing A - - 32 Motor speed rpm - - 1500 PTO speed rpm 480 480 - Saw blade Saw blade diameter mm 700 700 700 Min. log diameter cm 5 5 5 Max. log diameter cm 24 24 24 Noise Sound pressure level dB(A) Dimensions * Width cm 420 420 420 Depth cm 150 150 150 Height cm 250 250 250 Weight kg 490 510 560 Type ZE7.5 ZE11 Drive Drive type PTO/Electric motor PTO/Electric motor Output kW 15 / 7,5 Voltage V 400 400 Fusing A 20 32 Motor speed rpm 1500 1500 PTO speed rpm 480 480 Saw blade Saw blade diameter mm 700 700 Min. log diameter cm 5 5 Max. log diameter cm 24 24 Noise Sound pressure level dB(A) Dimensions * Width cm 420 420 Depth cm 150 150 Height cm 250 250 Weight kg . . *......The stated dimensions and weights are for guidance purposes and apply to the basic equipment. **....Power rating S6: continuous-operation periodic duty with related load changes – the percentage value is shown on the rating plate. Technical data 47
Page 1 and 2: Operating Instructions CutMaster 70
Page 3 and 4: Contents Contents 1 Foreword 5 1.1
Page 5 and 6: 1 1.1 1.2 1.3 1.4 Foreword Thank yo
Page 7 and 8: 2 2.1 Safety information Explanatio
Page 9 and 10: 2.4 2.5 The machine must always be
Page 11 and 12: 3 3.1 3.2 General Scope This user m
Page 13 and 14: 5 Three-point linkage connection 13
Page 15 and 16: 3.5 17 Rotational direction of pto
Page 17 and 18: 1 Neutral position 3 Delta position
Page 19 and 20: 4.3 The universal joint shaft must
Page 21 and 22: 5.1.2 5.1.3 "Comfort" model 1 2 1 F
Page 23 and 24: 5.3.2.1 5.3.3 1 Conveyor belt housi
Page 25 and 26: 6 Switching off the machine Before
Page 27 and 28: 7.3 Observe the road traffic regula
Page 29 and 30: 8.6 8.6.1 8.6.2 Oil level To check
Page 31 and 32: 9 9.1 9.1.1 9.2 Maintenance Before
Page 33 and 34: 9.2.1.1 9.2.2 1 Catch 2 Feed table
Page 35 and 36: 9.3.3 9.3.3.1 1 Transmission housin
Page 37 and 38: 9.3.3.3 9.4 9.4.1 Changing the V-be
Page 39 and 40: 9.4.2 9.4.3 Manufacturer Oil specif
Page 41 and 42: ▪ Remove the universal joint shaf
Page 43 and 44: 10.2 10.3 Loading plate for feed ta
Page 45: 11 Troubleshooting Before carrying
Page 49 and 50: 13 Service POSCH product To order s
Page 52: Your Posch-Dealer

CutMaster 700 - Posch

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?