CutMaster 700 - Posch

More documents

Recommendations

Info

Additional equipment 44 10.4 Chip extractor connection 1 1 Chip extractor connection 2 Deflector Connection for the extraction of chips. 2
11 Troubleshooting Before carrying out any troubleshooting operations on the machine it is essential to switch the drive off. Disconnect the machine from the mains. ▪ In addition, pull out the plug of the device. Disengage the universal joint shaft on the tractor. ▪ Before disengaging, turn the manual throttle to minimum. ▪ Remove the universal joint shaft from the tractor. Work on electrical equipment must only be carried out by qualified electricians. Fault Possible cause Remedy See page Electric motor fails to start or switches off frequently Electric motor fails to start Electric motor fails to start Faulty power supply cable Fuses keep tripping - incorrectly rated fuse for power supply cable Motor circuit breaker tripped Direction of rotation wrong Fuses on the brake switch board are faulty Limit switch not closed, incorrectly adjusted or defective Switch does not work Faulty power supply cable Hydraulic oil getting too hot Fuses keep tripping - incorrectly rated fuse for power supply cable Contactor or motor circuit breaker faulty Not enough hydraulic oil in hydraulic system Poor quality hydraulic oil Oil filter unclean or blocked Machine loses power Hydraulic oil getting too hot Sawing requires great amount of power Not enough hydraulic oil in hydraulic system Have the cable examined by a specialist Use correctly-rated fuses Use stronger power supply cable Swap over two phases Check the fuse and replace if necessary Close, adjust or change limit switch Have the cable examined by a specialist Have the cable examined by a specialist Have switch checked or send it in See [➙ 16] See [➙ 16] Check hydraulic oil level See [➙ 29] Change hydraulic oil See [➙ 37] Change filter insert See [➙ 39] See "Hydraulic oil getting too hot" Change hydraulic oil See [➙ 37] Saw blade is blunt Sharpening the saw blade Loose saw blade Tighten the hexagon nut on the drive shaft Saw disc is coated in resin Machine is noisy PTO shaft running too fast Machine is noisy Oil filter unclean or blocked Clean saw blade with a resin removing agent Adhere to specified speed Troubleshooting See [➙ 31] See [➙ 31] See [➙ 18] Change filter insert See [➙ 39] 45
Page 1 and 2: Operating Instructions CutMaster 70
Page 3 and 4: Contents Contents 1 Foreword 5 1.1
Page 5 and 6: 1 1.1 1.2 1.3 1.4 Foreword Thank yo
Page 7 and 8: 2 2.1 Safety information Explanatio
Page 9 and 10: 2.4 2.5 The machine must always be
Page 11 and 12: 3 3.1 3.2 General Scope This user m
Page 13 and 14: 5 Three-point linkage connection 13
Page 15 and 16: 3.5 17 Rotational direction of pto
Page 17 and 18: 1 Neutral position 3 Delta position
Page 19 and 20: 4.3 The universal joint shaft must
Page 21 and 22: 5.1.2 5.1.3 "Comfort" model 1 2 1 F
Page 23 and 24: 5.3.2.1 5.3.3 1 Conveyor belt housi
Page 25 and 26: 6 Switching off the machine Before
Page 27 and 28: 7.3 Observe the road traffic regula
Page 29 and 30: 8.6 8.6.1 8.6.2 Oil level To check
Page 31 and 32: 9 9.1 9.1.1 9.2 Maintenance Before
Page 33 and 34: 9.2.1.1 9.2.2 1 Catch 2 Feed table
Page 35 and 36: 9.3.3 9.3.3.1 1 Transmission housin
Page 37 and 38: 9.3.3.3 9.4 9.4.1 Changing the V-be
Page 39 and 40: 9.4.2 9.4.3 Manufacturer Oil specif
Page 41 and 42: ▪ Remove the universal joint shaf
Page 43: 10.2 10.3 Loading plate for feed ta
Page 47 and 48: 12 Technical data Type Z Z E11 Driv
Page 49 and 50: 13 Service POSCH product To order s
Page 52: Your Posch-Dealer

CutMaster 700 - Posch

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?