CutMaster 700 - Posch

More documents

Recommendations

Info

Maintenance 34 9.3 9.3.1 9.3.1.1 9.3.2 9.3.2.1 9.3.2.2 9.3.2.3 Incorrect use will invalidate any warranty claims. Resin-coated blades are excluded from the warranty exchange service. Changing the V-belt Tips on changing the V-belt If one V-belt is being changed, then all V-belts must be changed! The V-belts must be fitted loose. If they are "forced" onto the V-belt pulley, they may be damaged and quickly tear. The V-belts must be tensioned so that they deflect about 8 mm in the middle when thumb pressure is applied. V-belt types Machine type Belt Number (pcs.) Item no. Z XPA 1357 Lw 5 Z1940118 Z XPA 1357 Lw 4 Z1940118 E11 XPA 1450 Lw 3 Z1940140 ZE7.5 XPA 1285 Lw 2 Z1940086 ZE11 XPA 1400 Lw 1 Z1940120 "Compact" model Changing the V-belts on PTO drives See: Changing the V-belt on PTO/electric drives [➙ 34] Changing the V-belts on electric drives See: Changing the V-belts on PTO/electric drives [➙ 34] Changing the V-belts on PTO/electric drives 1 2 3 5 4 2 2
9.3.3 9.3.3.1 1 Transmission housing 4 Motor housing 2 Tensioning screw 5 Screw on motor housing 3 Screw on transmission housing ▪ Remove the V-belt guard. ▪ Undo the hexagon nuts of the tensioning screw (using a size 19 spanner) and loosen the tensioner so that you can remove the V-belts. ▪ Undo the four self-locking M12 hexagon nuts on the electric motor and push the motor backwards. ▪ Undo the bearing tensioning screw. ▪ Remove the old V-belts. ▪ Fit the new V-belts. ▪ Push the motor forwards until the two coupling halves have engaged. Ensure that the motor shaft and the bearing shaft are aligned. ▪ Tension the V-belts. ▪ Lock the lock nuts on both tensioning screws. ▪ Check the bearing V-belt tension and adjust if necessary. Then tighten the bearing tensioning screw. ▪ Refit the V-belt guard. Before operating, all protective guards must be attached to the machine. "Comfort" model Changing the V-belt on Comfort PTO drives 1 2 1 Tensioner 2 Tensioning screw ▪ Remove the V-belt guard. ▪ Undo the hexagon nuts of the tensioning screw (using a size 19 spanner) and loosen the tensioner so that you can remove the V-belts. ▪ Remove the old V-belts. ▪ Fit the new V-belts. ▪ Tension the V-belts. ▪ Lock the lock nuts on both tensioning screws. ▪ Refit the V-belt guard. Before operating, all protective guards must be attached to the machine. Maintenance 35
Page 1 and 2: Operating Instructions CutMaster 70
Page 3 and 4: Contents Contents 1 Foreword 5 1.1
Page 5 and 6: 1 1.1 1.2 1.3 1.4 Foreword Thank yo
Page 7 and 8: 2 2.1 Safety information Explanatio
Page 9 and 10: 2.4 2.5 The machine must always be
Page 11 and 12: 3 3.1 3.2 General Scope This user m
Page 13 and 14: 5 Three-point linkage connection 13
Page 15 and 16: 3.5 17 Rotational direction of pto
Page 17 and 18: 1 Neutral position 3 Delta position
Page 19 and 20: 4.3 The universal joint shaft must
Page 21 and 22: 5.1.2 5.1.3 "Comfort" model 1 2 1 F
Page 23 and 24: 5.3.2.1 5.3.3 1 Conveyor belt housi
Page 25 and 26: 6 Switching off the machine Before
Page 27 and 28: 7.3 Observe the road traffic regula
Page 29 and 30: 8.6 8.6.1 8.6.2 Oil level To check
Page 31 and 32: 9 9.1 9.1.1 9.2 Maintenance Before
Page 33: 9.2.1.1 9.2.2 1 Catch 2 Feed table
Page 37 and 38: 9.3.3.3 9.4 9.4.1 Changing the V-be
Page 39 and 40: 9.4.2 9.4.3 Manufacturer Oil specif
Page 41 and 42: ▪ Remove the universal joint shaf
Page 43 and 44: 10.2 10.3 Loading plate for feed ta
Page 45 and 46: 11 Troubleshooting Before carrying
Page 47 and 48: 12 Technical data Type Z Z E11 Driv
Page 49 and 50: 13 Service POSCH product To order s
Page 52: Your Posch-Dealer

CutMaster 700 - Posch

Create successful ePaper yourself

Delete template?

Save as template?