FSMH1621 - Service - Black & Decker

10
ENGLISH
(Original instructions)
u Press the Autoselect TM button (6) to the Wood/Laminate
setting.
u Pulling the handle (10) back will activate the steam pump.
After a few seconds steam will start to come out of the
steam head.
u Push and pull the steam mop slowly across the carpet to
thoroughly refresh each section.
Note: During use you may turn off the steam pump by returning
the handle (10) to the upright position, this convenient
feature will allow you to place the steam mop on the resting
mat (13) so that you may move items of furniture with out the
need to switch the appliance off.
u When you have finished using the steam mop, return the
handle (10) to the upright position and turn it ‘OFF’, place
it on the resting mat (13) and wait until the steam mop
cools down. (approximately five minutes)
Caution! If steam is observed escaping from the join between
the hand held steam cleaner and the steam mop body, switch
off and disconnect the unit from the mains supply. Allow to
cool. Remove the hand held steam cleaner from the steam
mop body. Inspect the seal (22) on the steam nozzle (4) and
hose (23) (fig. G). If the seal is missing or damaged then
please contact your nearest authorised repair agent. Do not
use the appliance. If the seal is in good condition re-fit the
hand held steam cleaner to the steam mop body ensuring that
it is seated firmly in place.
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean, return
the handle (10) to the upright position and turn the steam
mop ‘OFF’. Unplug the unit from the electrical wall outlet, refill
the water tank (8).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop on
the resting mat (13) with the handle (10) in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
After use (Fig. L & M)
u Return the handle (10) to the upright position and turn the
steam mop ‘OFF’,
u Place the steam mop on the resting mat (13) and wait until
the steam mop cools down. (approximately five minutes)
u Unplug the steam mop from the electrical wall outlet.
u Empty the water tank (8).
u Remove the cleaning pad (12) and wash it ready for
next use. (Take care to follow the wash care instructions
printed on the cleaning pad).
u Wrap the supply cable around the cable tidy hooks (15 &
16).
Note: The top cable tidy hook (16) rotates to easily release
the cable ready for next use.
u Clip the supply cable onto itself using the cable tidy clip
(29) close to the plug.
u Place steam mop on the resting mat (13) for storage.
Note: With the handle (10) in the upright position, the cable
neatly wrapped around the cable tidy hooks (15 & 16) and
secured with the cable tidy clip (29) your steam mop will stand
on its own for storage. Alternatively there is a hanging bracket
(30) built into the hand grip (31) which will allow your steam
mop to be hung from a suitable hook on the wall. Always
ensure that your wall hook is capable of supporting the weight
of the steam mop safely.
Hand held steam cleaning
u Attach the required accessory.
u Connect thehand held steam cleaner to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the hand held steam cleaner to heat up.
u Lift the lock off (2) and pull the trigger switch (3) to activate
the steam pump. After a few seconds steam will start to
come out of the accessory.
Note: During use you may turn off the steam pump by releasing
the trigger switch, this convenient feature will allow you to
place the hand held steam cleaner down for a short time so
that you may move items of furniture, then continue cleaning
without the need to switch the appliance off.
u When you have finished using the hand held steam
cleaner, release the trigger switch (3), turn it ‘OFF’and disconnect
from the mains supply. Wait until the steam mop
cools down before storing. (approximately five minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean,
turn the hand held steam cleaner ‘OFF’. Unplug the unit from
the electrical wall outlet, refill the water tank (8).
Maintenance and cleaning
Your Black & Decker corded appliance has been designed to
operate over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper appliance care and regular cleaning.
Warning! Before performing any maintenance or cleaning on
corded appliances switch off and unplug the appliance.
u Wipe your appliance over using a soft damp cloth.
u For stubborn marks you can use a mild solution of soap
and water to dampen your cloth.
u Inspect the seal (22) on the steam nozzle (4) and hose
(23) before each use (fig. G). If the seal is missing or damaged
then please contact your nearest authorised repair
agent. Do not use the appliance.
Care of the cleaning pads
Wash care instructions - No fabric conditioner - Allow to dry
fully before re-use.
Caution! Follow the cleaning instructions printed on the label
of the cleaning pad.