DESIGN OF A CUSTOM ASIC INCORPORATING CAN™ AND 1 ...
DESIGN OF A CUSTOM ASIC INCORPORATING CAN™ AND 1 ... DESIGN OF A CUSTOM ASIC INCORPORATING CAN™ AND 1 ...
Rack Card Calibration and Control – the controller in a module-based rack or chassis system often needs to identify what cards are installed, monitor key metrics like temperature, and track hot-swapped units. The 1 – Wire® memory, I/O, and temperature-sensor products solve this problem by providing a unique identity for every module in the system. The 1 – Wire® devices typically used include the DS2413, DS28EA00, DS2502, DS2505, DS2431, DS28EC20, DS2433, DS28E04, and DS28E01. PCB identification and authentication – factory-administered 64-bit serialization with embedded memory provides PCB/product labeling and storage of product information. Programmable features like OTP (One-Time Programmable) mode and write protection combine with SHA-1 based secure authentication to ensure that critical data cannot be altered once it is programmed. Storage of product characteristics, PCB hardware/software revision, maintenance records, and calibration constants are examples of typical usage. The 1 – Wire® devices typically used include the DS2401, DS2411, DS1963S, DS1992L, DS2502-E48, DS2502-E64, DS1982, DS1985, DS2431, DS28EC20, DS2433, DS28E01, and DS1961S. Accessory/Peripheral Identification and Control – typical applications include battery- pack and power-adapter identification, LED control, TEDS (Transducer Electronic Data Sheet) sensor identification/control, and consumable identification/control. The 1 – Wire® devices typically used include the DS2401, DS2411, DS2413, DS2502, DS2505, DS2431, DS28EC20, DS2433, and DS28E01. IP Protection, Secure Feature Control Clone Prevention – authentication solutions help OEMs (Original Equipment Manufacturers) protect product development and research 31
and development (R&D) investments by preventing low-quality knockoffs from entering the marketplace. Authentication solution options range from customization of the unique serial number factory-lasered into each device (providing controlled procurement access) to secure crypto-strong ISO/IEC 10118-3 SHA-1 based challenge and response for bi- directional authentication. The 1 – Wire® devices typically used include the DS2401, DS2411, DS1963S, DS1993L, DS1995L, DS1996L, DS2431, DS28EC20, DS28E01, and DS1961S. Consumer electronics – the types of 1 – Wire® devices used in consumer electronics include those of identification only (DS2401 and DS2411), identification plus control (DS2450), identification plus time (DS2417 and DS1904L), identification plus EEPROM (DS28EC20 and DS2431), and identification plus SHA – 1 secure EEPROM (DS28E01). Access control – the types of 1 – Wire® devices used for access control include those of identification only (DS1990A/DS1990R), identification plus NV SRAM (DS1992L, DS1993L, DS1995L, DS1996L), and identification plus EEPROM (DS1971, DS1972, DS1973). Electronic cash – the type of 1 – Wire® devices used for electronic cash tokens include those of identification plus NV SRAM (DS1963S) and identification plus SHA – 1 Secure EEPROM (DS1961S). Gaming devices – the type of 1 – Wire® devices used for the gaming industry include those of identification plus EEPROM (DS1977) due to high capacity (32KB) and password protection. 32
- Page 5 and 6: LIST OF ABBREVIATIONS AND SYMBOLS A
- Page 7 and 8: ISO International Organization for
- Page 9 and 10: SI Serial In SO Serial Out SOF Star
- Page 11 and 12: ACKNOWLEDGEMENTS I would like to ex
- Page 13 and 14: 2.4 Types of Devices...............
- Page 15 and 16: 4.3.5 Communication Speed Different
- Page 17 and 18: 5.3.21.1 Synchronization Test (test
- Page 19 and 20: 5.3 Resource Utilization...........
- Page 21 and 22: LIST OF FIGURES 2.1 1 - Wire® Netw
- Page 23 and 24: 4.12 Read-Data Time Slot...........
- Page 25 and 26: 6.4 DS1996 Address Registers ......
- Page 27 and 28: manufacturing process. Structured o
- Page 29 and 30: describes the 1 - Wire® and CAN co
- Page 31 and 32: 2.2 1 - Wire® Overview The basis o
- Page 33 and 34: All 1 - Wire® masters described in
- Page 35 and 36: attachments, microcontroller with b
- Page 37 and 38: Figure 2.3 Bidirectional port pin w
- Page 39 and 40: 2.3.3 Synthesizable 1 - Wire® Bus
- Page 41 and 42: Figure 2.7 UART/RS232 Serial Port I
- Page 43 and 44: hardware. Through control registers
- Page 45 and 46: Table 2.2 1 - Wire® Bus Operations
- Page 47 and 48: 2.3.6 1 - Wire® Search Algorithm F
- Page 49 and 50: detected. This ‘read two bits’
- Page 51 and 52: in Figure 2.15. Alternatively, the
- Page 53 and 54: of the bit, then write the desired
- Page 55: 2.4.2 Device Functions and Typical
- Page 59 and 60: 2.5 Network Types and Precedents As
- Page 61 and 62: 2.5.2 1 - Wire® Network Topologies
- Page 63 and 64: 2.5.3 1 - Wire® Network Limitation
- Page 65 and 66: with a single selected slave. If an
- Page 67 and 68: user group was founded in March of
- Page 69 and 70: protocol on multiple media for maxi
- Page 71 and 72: ecessive bit and the monitored stat
- Page 73 and 74: specification: Start-Of-Frame, Arbi
- Page 75 and 76: Cyclic Redundancy Check (CRC) Field
- Page 77 and 78: Arbitration FieldThe Arbitration Fi
- Page 79 and 80: SOF SOF Bit 28 Bit 27 Arbitration f
- Page 81 and 82: Afterwards it starts transmitting s
- Page 83 and 84: Figure 3.9 Structure of the Interfr
- Page 85 and 86: error occurs, an Error Frame is gen
- Page 87 and 88: Table 3.4 Error Flag Output Timing
- Page 89 and 90: 3.5.2 Error-Passive A node becomes
- Page 91 and 92: where tNBT is the Nominal Bit Time
- Page 93 and 94: Figure 3.12 Propagation Delay Betwe
- Page 95 and 96: 3.6.4 Synchronization t t t t (3.
- Page 97 and 98: opposite value is inserted into the
- Page 99 and 100: many systems, the bus length will b
- Page 101 and 102: CHAPTER 4 THE CHALLENGES OF INTERFA
- Page 103 and 104: In June 2004, Maxim Integrated Prod
- Page 105 and 106: Wearable sensor technology is a new
and development (R&D) investments by preventing low-quality knockoffs from entering<br />
the marketplace. Authentication solution options range from customization of the unique<br />
serial number factory-lasered into each device (providing controlled procurement access)<br />
to secure crypto-strong ISO/IEC 10118-3 SHA-1 based challenge and response for bi-<br />
directional authentication. The 1 – Wire® devices typically used include the DS2401,<br />
DS2411, DS1963S, DS1993L, DS1995L, DS1996L, DS2431, DS28EC20, DS28E01, and<br />
DS1961S.<br />
Consumer electronics – the types of 1 – Wire® devices used in consumer electronics<br />
include those of identification only (DS2401 and DS2411), identification plus control<br />
(DS2450), identification plus time (DS2417 and DS1904L), identification plus EEPROM<br />
(DS28EC20 and DS2431), and identification plus SHA – 1 secure EEPROM (DS28E01).<br />
Access control – the types of 1 – Wire® devices used for access control include those of<br />
identification only (DS1990A/DS1990R), identification plus NV SRAM (DS1992L,<br />
DS1993L, DS1995L, DS1996L), and identification plus EEPROM (DS1971, DS1972,<br />
DS1973).<br />
Electronic cash – the type of 1 – Wire® devices used for electronic cash tokens include<br />
those of identification plus NV SRAM (DS1963S) and identification plus SHA – 1<br />
Secure EEPROM (DS1961S).<br />
Gaming devices – the type of 1 – Wire® devices used for the gaming industry include<br />
those of identification plus EEPROM (DS1977) due to high capacity (32KB) and<br />
password protection.<br />
32