Parker O-Ring Handbook.pdf

More documents

Recommendations

Info

Compatibility Tables for Gases, Fluids, Solids 7-2 Parker O-Ring I 5700 Handbook Compatibility Tables Tables for Gases, Gases, Fluids, Fluids, Solids Solids COMPOUND COMPATIBILITY RATING 1 - Satisfactory 2 - Fair (usually OK for static seal) 3 - Doubtful (sometimes OK for static seal) 4 - Unsatisfactory x - Insuffi cient Data Recommended Nitrile NBR Hydrogenated Nitrile HNBR Ethylene Propylene EPDM Fluorocarbon FKM Hifl uor FKM Perfl uoroelastomer FFKM Afl as (TFE/Propylene) FEPM Neoprene/Chloroprene CR Styrene-Butadiene SBR Polyacrylate ACM Polyurethane AU, EU Butyl IIR Butadiene BR Isoprene IR Natural Rubber NR Hypalon CSM Fluorosilicone FVMQ Silicone MQ, VMQ, PVMQ — A — A-A-52624 E1267-80 X X X X X X X X X X X X X X X X X X A-A-59290 E1267-80 X X X X X X X X X X X X X X X X X X Abietic Acid V3819-75 X X X X 1 1 X X X X X X X X X X X X Acetaldehyde E0540-80 3 3 2 4 1 1 3 3 3 4 4 2 2 2 2 3 4 2 Acetamide C0873-70 1 1 1 3 1 1 2 1 4 4 4 2 4 4 4 2 1 2 Acetanilide E0540-80 3 3 1 3 1 1 X 1 1 4 4 1 1 1 1 1 1 2 Acetic Acid, 30% E0540-80 X X 1 X 1 1 X X X X X X X X X X X X Acetic Acid, 5% E0540-80 2 2 1 1 1 1 1 1 2 4 4 1 2 2 2 1 2 1 Acetic Acid, Glacial E0540-80 2 2 1 2 1 1 3 4 2 4 4 2 2 2 2 3 2 1 Acetic Acid, Hot, High Pressure FF200-75 4 4 3 4 2 1 3 4 4 4 4 4 4 4 4 3 4 3 Acetic Anhydride C0873-70 3 4 2 4 1 1 2 2 2 4 4 2 2 2 2 2 4 2 Acetoacetic Acid E0540-80 3 3 1 3 1 1 X 1 1 4 4 1 1 1 1 1 1 2 Acetone E0540-80 4 4 1 4 2 1 2 4 4 4 4 1 4 4 4 3 4 4 Acetone Cyanohydrin E0540-80 3 3 1 3 1 1 X 1 1 4 4 1 1 1 1 1 1 2 Acetonitrile (Methyl Cyanide) E0540-80 3 3 1 3 1 1 1 X X X X X X X X X X X Acetophenetidine V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Acetophenone E0540-80 4 4 1 4 2 1 2 4 4 4 4 2 4 4 4 4 4 4 Acetotoluidide V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Acetyl Acetone E0540-80 4 4 1 4 2 1 2 4 4 4 4 1 4 4 4 4 4 4 Acetyl Bromide V1164-75 4 4 1 1 1 1 2 4 4 4 4 1 4 4 4 4 4 4 Acetyl Chloride V1164-75 4 4 4 1 1 1 2 4 4 4 4 4 4 4 4 4 1 4 Acetylene E0540-80 1 1 1 1 1 1 1 2 2 4 4 1 2 2 2 2 X 2 Acetylene Tetrabromide V1164-75 4 4 1 1 1 1 1 2 4 X 4 1 X X X X X X Acetylene Tetrachloride V1164-75 4 4 1 1 1 1 1 2 4 X 4 1 X X X X X X Acetylsalicylic Acid V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Acids, Non-organic V3819-75 X X X X 1 1 X X X X X X X X X X X X Acids, Organic V3819-75 X X X X 1 1 X X X X X X X X X X X X Aconitic Acid V3819-75 X X X X 1 1 X X X X X X X X X X X X Acridine V3819-75 X X X X 1 1 X X X X X X X X X X X X Acrolein E0540-80 3 3 1 3 1 1 X 1 1 4 4 1 1 1 1 1 1 2 Acrylic Acid V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Acrylonitrile FF500-75 4 4 4 3 1 1 3 4 3 4 4 4 X 3 3 3 4 4 Adipic Acid E0540-80 1 1 2 X 1 1 2 X X X X X X X X X X X Aero Lubriplate N0674-70 1 1 4 1 1 1 2 1 2 1 1 4 4 4 4 1 1 2 Aero Shell 17 Grease N0674-70 1 1 4 1 1 1 2 2 4 1 1 4 4 4 4 1 1 2 Approximate Service Temperature Ranges for Commonly Used Basic Polymer Types* Nitrile (General Service) -34°C to 121°C (-30°F to 250°F)* AFLAS -9°C to 232°C (15°F to 450°F)* Nitrile (Low Temperature) -55°C to 107°C (-65°F to 225°F)* Neoprene -51°C to 107°C (-60°F to 225°F)* Hydrogenated Nitrile -32°C to 149°C (-23°F to 300°F)* Polyacrylate -21°C to 177°C (- 5°F to 350°F)* Ethylene Propylene -57°C to 121°C (-70°F to 250°F)* Polyurethane -40°C to 82°C (-40°F to 180°F)* Fluorocarbon -26°C to 205°C (-15°F to 400°F)* Butyl -59°C to 120°C (-75°F to 250°F)* Hifl uor -26°C to 205°C (-15°F to 400°F)* Fluorosilicone -73°C to 177°C (-100°F to 350°F)* Perfl uoroelastomer (Parofl uor) -26°C to 320°C (-15°F to 608°F)* Silicone -115°C to 232°C (-175°F to 450°F)* NOTE: *These temperature ranges will apply to the majority of media for which the material is potentially recommended. With some media however, the service temperature range may be signifi cantly different. ALWAYS TEST UNDER ACTUAL SERVICE CONDITIONS. Parker Hannifi n Corporation • O-Ring Division 2360 Palumbo Drive, Lexington, KY 40509 Phone: (859) 269-2351 Fax: (859) 335-5128 www.parkerorings.com
COMPOUND COMPATIBILITY RATING 1 - Satisfactory 2 - Fair (usually OK for static seal) 3 - Doubtful (sometimes OK for static seal) 4 - Unsatisfactory x - Insuffi cient Data Parker O-Ring Handbook Nitrile NBR Hydrogenated Nitrile HNBR Ethylene Propylene EPDM Fluorocarbon FKM Hifl uor FKM Perfl uoroelastomer FFKM Afl as (TFE/Propylene) FEPM Neoprene/Chloroprene CR Styrene-Butadiene SBR Polyacrylate ACM Polyurethane AU, EU Butyl IIR Butadiene BR Isoprene IR Natural Rubber NR Recommended Aero Shell 560 VM835-70 X X X X X X X X X X X X X X X X X X Aero Shell 750 V1164-75 2 2 4 1 1 1 2 4 4 2 4 4 4 4 4 4 2 4 Aero Shell 7A Grease ( MIL-G-23827) N0674-70 2 2 4 1 1 1 2 2 4 1 1 4 4 4 4 1 1 2 Aero Shell IAC N0674-70 1 1 4 1 1 1 2 2 4 1 1 4 4 4 4 1 1 2 Aerosafe 2300 E0540-80 4 4 1 4 1 1 2 4 4 4 4 2 4 4 4 4 3 3 Aerosafe 2300W E0540-80 4 4 1 4 1 1 2 4 4 4 4 2 4 4 4 4 3 3 Aerozene 50 (50% Hydrazine 50% UDMH) E0540-80 3 3 1 4 3 2 2 4 4 X 4 1 4 4 4 4 4 4 Air, Below 200° F E0540-80 2 2 1 1 1 1 1 1 2 1 2 1 2 2 2 1 1 1 Air, 200 - 300° F S0604-70 3 3 2 1 1 1 1 2 4 2 3 2 4 4 4 2 1 1 Air, 300 - 400° F S0604-70 4 4 4 1 1 1 2 4 4 4 4 4 4 4 4 4 2 1 Air, 400 - 500° F S0455-70 4 4 4 3 2 2 3 4 4 4 4 4 4 4 4 4 4 2 Aliphatic Dicarboxylic Acid V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Alkanes (Paraffi n Hydrocarbons) N0674-70 1 1 4 1 1 1 X 2 4 1 1 4 4 4 4 2 1 2 Alkanesulfonic Acid N0674-70 1 1 4 1 1 1 X 2 4 1 1 4 4 4 4 2 1 2 Alkazene V1164-75 4 4 4 2 1 1 2 4 4 4 4 4 4 4 4 4 2 4 Alkenes (Olefi n Hydrocarbons) V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Alkyl Acetone E0540-80 3 3 1 3 2 1 X 1 1 4 4 1 1 1 1 1 1 2 Alkyl Alcohol N0674-70 1 1 4 1 1 1 X 2 4 1 1 4 4 4 4 2 1 2 Alkyl Amine N0674-70 1 1 4 1 1 1 X 2 4 1 1 4 4 4 4 2 1 2 Alkyl Aryl Sulfonates N0674-70 1 1 4 1 1 1 X 2 4 1 1 4 4 4 4 2 1 2 Alkyl Aryl Sulfonics N0674-70 1 1 4 1 1 1 X 2 4 1 1 4 4 4 4 2 1 2 Alkyl Benzene V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Alkyl Chloride V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Alkyl Lithium FF500-75 X X X X X X X X X X X X X X X X X X Alkyl Sulfi de* V1164-75 2 2 4 1 1 1 X 4 4 4 3 4 4 4 4 4 2 X Alkylnaphthalene Sulfonic Acid N0674-70 1 1 4 1 1 1 X 2 4 1 1 4 4 4 4 2 1 2 Allyl Chloride V1164-75 2 2 4 1 1 1 X 1 X X X X X X X X X X Allylidene Diacetate E0540-80 3 3 1 3 2 1 X 1 1 4 4 1 1 1 1 1 1 2 Alpha Picoline E0540-80 3 3 1 3 1 1 X 1 1 4 4 1 1 1 1 1 1 2 Aluminum Acetate E0540-80 2 2 1 4 1 1 2 2 2 4 4 1 4 1 1 4 4 4 Aluminum Bromide N0674-70 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 Aluminum Chlorate E0540-80 3 3 1 3 1 1 X 1 1 4 4 1 1 1 1 1 1 2 Aluminum Chloride N0674-70 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 2 Aluminum Ethylate V3819-75 X X X X 1 1 X X X X X X X X X X X X Aluminum Fluoride N0674-70 1 1 1 1 1 1 1 1 1 X 3 1 1 1 2 1 1 2 Aluminum Fluorosilicate* V3819-75 X X X X 1 1 X X X X X X X X X X X X Aluminum Formate E0540-80 3 3 1 3 1 1 X 1 1 4 4 1 1 1 1 1 1 2 Aluminum Hydroxide E0540-80 2 X 1 2 1 1 1 X X X X X X X X X X 2 Aluminum Linoleate N0674-70 1 1 4 1 1 1 X 2 4 1 1 4 4 4 4 2 1 2 Aluminum Nitrate N0674-70 1 1 1 1 1 1 1 1 1 X 3 1 1 1 1 1 X 2 Approximate Service Temperature Ranges for Commonly Used Basic Polymer Types* Nitrile (General Service) -34°C to 121°C (-30°F to 250°F)* AFLAS -9°C to 232°C (15°F to 450°F)* Nitrile (Low Temperature) -55°C to 107°C (-65°F to 225°F)* Neoprene -51°C to 107°C (-60°F to 225°F)* Hydrogenated Nitrile -32°C to 149°C (-23°F to 300°F)* Polyacrylate -21°C to 177°C (- 5°F to 350°F)* Ethylene Propylene -57°C to 121°C (-70°F to 250°F)* Polyurethane -40°C to 82°C (-40°F to 180°F)* Fluorocarbon -26°C to 205°C (-15°F to 400°F)* Butyl -59°C to 120°C (-75°F to 250°F)* Hifl uor -26°C to 205°C (-15°F to 400°F)* Fluorosilicone -73°C to 177°C (-100°F to 350°F)* Perfl uoroelastomer (Parofl uor) -26°C to 320°C (-15°F to 608°F)* Silicone -115°C to 232°C (-175°F to 450°F)* NOTE: *These temperature ranges will apply to the majority of media for which the material is potentially recommended. With some media however, the service temperature range may be signifi cantly different. ALWAYS TEST UNDER ACTUAL SERVICE CONDITIONS. Hypalon CSM Fluorosilicone FVMQ Silicone MQ, VMQ, PVMQ Parker Hannifi n Corporation • O-Ring Division 2360 Palumbo Drive, Lexington, KY 40509 Phone: (859) 269-2351 Fax: (859) 335-5128 www.parkerorings.com Compatibility Tables for Gases, Fluids, Solids 7-3
Page 1 and 2:
aerospace climate control electrome
Page 3 and 4:
50 th 50 th 50 th Anniversary Editi
Page 5 and 6:
Section I - Introduction 1.0 How to
Page 7 and 8:
1.4 Operation All robust seals are
Page 9 and 10:
1.7.1 Static Seals In a truly stati
Page 11 and 12:
1.11 Comparison of Common Seal Type
Page 13 and 14:
Section II - Basic O-Ring Elastomer
Page 15 and 16:
2.1.2 Rubber Rubber-like materials
Page 17 and 18:
2.2.6 Chloroprene Rubber (CR) Chlor
Page 19 and 20:
2.3 Compound Selection and Numberin
Page 21 and 22:
O-ring seal, whether static or dyna
Page 23 and 24:
Percent Compression 40% 30% 20% 10%
Page 25 and 26:
Percent Compression 40% 30% 20% 10%
Page 27 and 28:
Compression Set (% ) 100 Figure 2-1
Page 29 and 30:
2.4.12 Thermal Effects All rubber i
Page 31 and 32:
coeffi cient of expansion for that
Page 33 and 34:
2.6 Aging Deterioration with time o
Page 35 and 36:
A well-known rapid method for mater
Page 37 and 38:
2.13.2 Temperature Temperature rang
Page 39 and 40:
100 80 60 40 20 0 °C -50 °F -58 -
Page 41 and 42:
misapplication might be greatly red
Page 43 and 44:
c. Elongation Change Experience wil
Page 45 and 46:
is possible to receive a part with
Page 47 and 48:
Section III - O-Ring Applications 3
Page 49 and 50:
3.1.2 Temperature Operating tempera
Page 51 and 52:
O-Lube has some unique advantages.
Page 53 and 54:
Parker Boss Kit Sizes Size Dimensio
Page 55 and 56:
Recovery Percent of Original Delect
Page 57 and 58:
3.9.5 Fuels for Automobile Engines
Page 59 and 60:
Parker Seal produces a number of co
Page 61 and 62:
3.9.16 Fungus-Resistant Compounds B
Page 63 and 64:
3.9.17.2 Concentrates Containing Mi
Page 65 and 66:
Where temperatures do not go below
Page 67 and 68:
Permeability Rate - CC/SEC/ATM Effe
Page 69 and 70:
Underwriters’ Laboratories Approv
Page 71 and 72:
Parker Seal Elastic Drive Belt Comp
Page 73 and 74:
Parker O-Ring Handbook Gas Permeabi
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Section IV - Static O-Ring Sealing
Page 83 and 84:
The 4-3 and 4-7 design charts are o
Page 85 and 86:
(e) 0° to 5° (Typ.) 63 Break Corn
Page 87 and 88:
215 1.301 1.305 1.079 1.060 1.063 1
Page 89 and 90:
Guide for Design Table 4-2 If Desir
Page 91 and 92:
Parker O-Ring Handbook Gland Dimens
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Dovetail Grooves It is often necess
Page 101 and 102:
Parker O-Ring Handbook This type of
Page 103 and 104:
F .031 .016 RAD K Parker O-Ring Han
Page 105 and 106:
Gland Detail 0° to 5° Break Corne
Page 107 and 108:
Section V - Dynamic O-Ring Sealing
Page 109 and 110:
When a cylinder rod extends out int
Page 111 and 112: It can be clearly seen from Figure
Page 113 and 114: 5.11 Friction Friction, either brea
Page 115 and 116: 5-9 Dynamic O-Ring Sealing Parker H
Page 117 and 118: For the same conditions, friction a
Page 119 and 120: 5.15 Spiral Failure A unique type o
Page 121 and 122: 5.16.1 Small Amount of Leakage 1. E
Page 123 and 124: Recommended dimensions for fl oatin
Page 125 and 126: for this service. See Section II, B
Page 127 and 128: 5.30.2 Calculation of Drive Belt Cr
Page 129 and 130: Parker O-Ring Handbook Gland Design
Page 131 and 132: 124 125 126 127 128 129 130 131 132
Page 133 and 134: 240 241 242 243 244 245 246 247 325
Page 135 and 136: 448 449 450 451 452 453 454 455 456
Page 137 and 138: X Gland Detail 0° to 5° Break Cor
Page 139 and 140: Parker O-Ring Handbook Gland Dimens
Page 141 and 142: 5.31.3 O-Ring Glands for Pneumatic
Page 143 and 144: Parker O-Ring Handbook Design Table
Page 145 and 146: 5.31.4 O-Ring Glands for Rotary Sea
Page 147 and 148: Parker O-Ring Handbook Rotary O-Rin
Page 149 and 150: Parker O-Ring Handbook Rotary O-Rin
Page 151 and 152: Section VI - Back-Up Rings 6.1 Intr
Page 153 and 154: 6.4.2 Metal Non-Extrusion Rings In
Page 155 and 156: Parker Parbak 8-Series Dimensions (
Page 157 and 158: Parker Parbak 8-Series Dimensions (
Page 159 and 160: Back-Up Rings Cross Reference (Cont
Page 161: Parker O-Ring Handbook Section VII
Page 165 and 166: COMPOUND COMPATIBILITY RATING 1 - S
Page 213 and 214:
COMPOUND COMPATIBILITY RATING 1 - S
Page 215 and 216:
COMPOUND COMPATIBILITY RATING 1 - S
Page 217 and 218:
Section VIII - Specifi cations 8.1
Page 219 and 220:
Military Fluid Specifi cation Descr
Page 221 and 222:
AMS (1) and NAS (2) Rubber Specifi
Page 223 and 224:
Parker O-Ring Handbook Compound Sel
Page 225 and 226:
Section IX Sizes Parker Series 2-XX
Page 227 and 228:
Table 9-1: Parker Series 2-XXX O-Ri
Page 229 and 230:
Parker O-Ring Handbook Parker Serie
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Parker Series 5-XXX O-Ring Sizes (C
Page 239 and 240:
Parker Series 5-XXX O-Ring Sizes (C
Page 241 and 242:
Series 5-XXX Locator Table Size I.D
Page 243 and 244:
Parker O-Ring Handbook Inside Diame
Page 245 and 246:
JIS B2401 Sizes JIS Thickness Inner
Page 247 and 248:
Parker O-Ring Handbook Unusual Size
Page 249 and 250:
Parker O-Ring Handbook Unusual Size
Page 251 and 252:
Section X - Appendix 10.1 O-Ring Fa
Page 253 and 254:
10.1.1.2 Extrusion and Nibbling Ext
Page 255 and 256:
10.1.1.6 Installation Damage Many O
Page 257 and 258:
Parker Seal also has the capability
Page 259 and 260:
10.3 Glossary of Seal and Rubber Te
Page 261 and 262:
Flash: Excess rubber left around ru
Page 263 and 264:
(b) REP (Roentgen equivalent-physic
Page 265 and 266:
10.4 Abbreviations ACM Polyacrylate
Page 267 and 268:
Compound Shrinkage Class Compound N
Page 269 and 270:
Table 10-8: Dimensions From Standar
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Parker O-Ring Handbook Dimensions F
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Appendix 10-32 Parker O-Ring Handbo
Page 285 and 286:
Index — A — Abbreviations. . .
Page 287 and 288:
International O-Ring Standards and
Page 289 and 290:
Offer of Sale 1. Terms and Conditio
Page 291 and 292:
Parker’s Total inPHorm Take the g
show all

Parker O-Ring Handbook.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?