MCP23008/MCP23S08 - Microchip

More documents

Recommendations

Info

MCP23008/MCP23S08 2.1 DC Characteristics DC Characteristics Operating Conditions (unless otherwise indicated): 1.8V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +85°C (I-Temp) 4.5V ≤ VDD ≤ 5.5V at -40°C ≤ TA ≤ +125°C (E-Temp) (Note 1) Param No. Characteristic Sym Min Typ Max Units Conditions D001 Supply Voltage VDD 1.8 — 5.5 V D002 VDD Start Voltage to Ensure Power-on Reset VPOR — VSS — V D003 VDD Rise Rate to Ensure Power-on Reset SVDD 0.05 — — V/ms Design guidance only. Not tested. D004 Supply Current IDD — — 1 mA SCL/SCK = 1 MHz D005 Standby current IDDS — — 1 µA Input Low-Voltage — — 2 µA 4.5V - 5.5V @ +125°C (Note 1) D030 A0, A1 (TTL buffer) VIL VSS — 0.15 VDD V D031 CS, GPIO, SCL/SCK, SDA, A2, RESET (Schmitt Trigger) VSS — 0.2 VDD V Input High-Voltage D040 A0, A1 (TTL buffer) D041 CS, GPIO, SCL/SCK, SDA, A2, RESET (Schmitt Trigger) VIH 0.25 VDD + 0.8 — VDD V 0.8 VDD — VDD V For entire VDD range. D060 Input Leakage Current I/O port pins IIL — — ±1 µA VSS ≤ VPIN ≤ VDD D065 Output Leakage Current I/O port pins ILO — — ±1 µA VSS ≤ VPIN ≤ VDD D070 GPIO weak pull-up current Output Low-Voltage IPU 40 75 115 µA VDD = 5V, GP Pins = VSS –40°C ≤ TA ≤ +85°C D080 GPIO VOL — — 0.6 V IOL = 8.5 mA, VDD = 4.5V INT — — 0.6 V IOL = 1.6 mA, VDD = 4.5V SO, SDA — — 0.6 V IOL = 3.0 mA, VDD = 1.8V SDA Output High-Voltage — — 0.8 V IOL = 3.0 mA, VDD = 4.5V D090 GPIO, INT, SO VOH VDD – 0.7 — — V IOH = -3.0 mA, VDD = 4.5V VDD – 0.7 — — IOH = -400 µA, VDD = 1.8V Capacitive Loading Specs on Output Pins D101 GPIO, SO, INT CIO — — 50 pF D102 SDA CB — — 400 pF Note 1: This parameter is characterized, not 100% tested. DS21919E-page 24 © 2007 Microchip Technology Inc.
MCP23008/MCP23S08 FIGURE 2-1: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS FIGURE 2-2: RESET AND DEVICE RESET TIMER TIMING VDD RESET Internal RESET Output pin SCL and SDA pin MCP23008 VDD 1kΩ 135 pF 34 30 © 2007 Microchip Technology Inc. DS21919E-page 25 32 Pin 50 pF
Page 1 and 2: Features • 8-bit remote bidirecti
Page 3 and 4: © 2007 Microchip Technology Inc. D
Page 5 and 6: 1.0 DEVICE OVERVIEW The MCP23X08 de
Page 7 and 8: FIGURE 1-1: MCP23008 I 2 C DEVICE P
Page 9 and 10: 1.5 GPIO Port The GPIO module conta
Page 11 and 12: 1.6.2 INPUT POLARITY (IPOL) REGISTE
Page 13 and 14: 1.6.4 DEFAULT COMPARE (DEFVAL) REGI
Page 15 and 16: 1.6.6 CONFIGURATION (IOCON) REGISTE
Page 17 and 18: 1.6.8 INTERRUPT FLAG (INTF) REGISTE
Page 19 and 20: 1.6.10 PORT (GPIO) REGISTER The GPI
Page 21 and 22: 1.7 Interrupt Logic The interrupt o
Page 23: 2.0 ELECTRICAL CHARACTERISTICS Abso
Page 27 and 28: TABLE 2-2: I 2 C BUS DATA REQUIREME
Page 29 and 30: FIGURE 2-6: SPI OUTPUT TIMING CS SC
Page 31 and 32: TABLE 2-4: GP AND INT PINS AC Chara
Page 33 and 34: 3.0 PACKAGING INFORMATION 3.1 Packa
Page 35 and 36: 18-Lead Plastic Small Outline (SO)
Page 37 and 38: 20-Lead Plastic Shrink Small Outlin
Page 39 and 40: APPENDIX A: REVISION HISTORY Revisi
Page 41 and 42: PRODUCT IDENTIFICATION SYSTEM MCP23
Page 43 and 44: Note the following details of the c

MCP23008/MCP23S08 - Microchip

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?