DESK PANEL DPA - Lmc

DESK PANEL DPA
DPA:
Features:
Control panel for up to 4 actuators in parallel
Plastic housing with mounting holes (LINAK does not deliver
the screws)
Compatible with CBD1, CBD2 (not CBD2N), CBD3 and CBD4
1.58 m straight cable
Colour: Charcoal grey RAL 7016, buttons RAL 7038
Adjustable panel
Options:
Customised front cover
The compact design and mounting friendliness of the
desk panel makes it suitable for placing under e.g. height
adjustable desks.
The panel is compatible with all DESKLINE ® control boxes
with micro-processor.

Operation of the DPA in connection with DESKLINE ® systems (not CBD2N)
The Desk Panel is used to operate the DESKLINE ® system. The two arrow buttons are used for parallel drive.
Parallel drive ( )
The arrow buttons start parallel drive. The function is only actibated when holding the button down.
Dimensions:
Cable guidance
Mounting guidelines:
DPA
Ordering example
DPA
Standard cable outlet
cover
K 0 6
Cables:
Specifications subject to change without prior notice.
It is the responsibility of the product user to determine the suitability
of LINAK A/S products for a specific application. LINAK will at point of
delivery replace/repair defective products covered by the warranty
if promptly returned to the factory. No liability is assumed beyond
such replacement/repair.
53.4
13
Ø4.4
24
49.6
55.5
28
The DPA can be mounted on the desktop so that the keys are
either facing upwards or outwards.
Alternatively the DPA can be mounted fl at under the desktop
with the keys facing downwards.
6 = Straight 1580 mm 8 pole Modular Jack
Colour: 0=DarkGreyRAL7016
Type K = CBD1/CBD2E/CBD3/CBD4
25.5
33.5
8
90-180°
Copyright © LINAK 04.02 . MA M9-02-064-D . Chapter 21.1.1

DESKLIFT DL4
DL4:
Features:
Compact design where guide and actuator function are an
integrated unit
Max. thrust 800 N (per leg)
Duty cycle: 10% or 6 min./hour or max. 2 min. at continuous use
at full load
Max. speed: 43 mm/sec. with CBD4
Built-in limit switches (not adjustable)
Installation dimension 560 mm and stroke length 675 mm
Dimension column: see drawing
Low and uniform noise level
Typical current consumption: 7,8 amp. at max. thrust (per DL4)
Colour: black RAL 9005 or grey RAL 9006 “aluminium white”
Hall sensor (enables parallel drive with CBD4)
Ambient temperature: +5°C to +40°C
Compatible with DESKLINE ® CBD4 control box
Mounting bracket for crossbar in parallel system
Double acting brake for increased self locking
Bending moment: Max. 1350 Nm static, max. 150 Nm dynamic
The DESKPOWER DL4 is a new development specially
made to extend the adjustment range of desks. LINAK fulfils
even the strongest European standards that demand a
range of adjustment from 600 mm up to 1250 mm.
The DL4 is a three part telescopic column with a similar
movement of the middle profiles in a parallel system.
DL4 is a compact lifting unit with a small installation
dimension where the guide and actuator function are
integrated. The whole actuating unit with the motor
is placed in the column itself. This feature ensures an
optimum freedom of design.
Each DESKLIFT lifting unit is equipped with a motor. The
DESKLIFT lifting column is part of a 2 parallel or a 3 parallel
system.
The parallel drive is obtained by means of special software
in the CBD4 that also compensates for an uneven load on
the desk.
The control box CBD4 is designed with soft start/stop
function.

DL4 dimensions:
STANDARD CABLE LENGTH = Approx. 50 mm
STROKE = 675±2mm
At a fully retracted length of 560 mm and a stroke length of 675 mm it is possible for a standard system to obtain an adjustment
interval of the tabletop of e.g. 600 - 1275 mm. Thus the desk can be used for sitting as well as standing work.
Min. desk height
(CENTER R6.4)
26.18
M6x4
85.2 (CENTER R6.4)
R246.33
80±0.2
98±0.3
SEE DETAIL B
Height of the DL4 in the lowest position
Floor level
Table top
Absorbing
material
R6.4
22±0.2
46.6 ±0.3
DETAIL B
28±0.2
560±2
552±0.5
1235
109.2 ±0.3
DETAIL A
Example of how to mount the
DESKPOWER ® system
Placement of a monitor directly above the leg may cause malfunction of the monitor. Magnets inside
the motor may interrupt the picture on the monitor depending on the distance and type of monitor. If
this is the case the problem may be solved by placing an iron plate/tube or another magnetic material,
somewhat larger then the DL4, between the motor and the desktop.
R241.48
87±0.2
30
R12
M6x4
57.8 ±0.3
SEE DETAIL A
B
Screw length
Min.B+10mm
Max.B+15mm

DL4
Ordering example:
Motor cables:
DL4 0 0
0 B 0 0 675 560
Installation dim
Motor cables must be ordered separately:
Ordering number: 0617100 (1000 mm black motor cable)
0617200 (2000 mm black motor cable)
0617250 (2500 mm black motor cable)
Bracket for travers:
Technical specifi cations:
2
Stroke Length
Motor/gear type
Option
Colour
Mounting bracket
Option
Option
Actuator type
Ordering number for crossbar brackets (box containing 100 pcs.): 0611871
19
32
X
560 mm
675 mm
0=Standard 43mm/s
0 = Standard
A = Grey (RAL 9006)
B = Black (RAL 9005)
0 = none
1 = Standard bracket
0 = Standard
0 = Standard
DESKPOWER
Type Thrust Self-lock Speed Duty Amp. at Transformer
max. (N) at cycle full load type: 2P
(N) pr. DL4 0 load in connection
pr. DL4 (mm/s) (%) with CBD4
DL4 700 2400 43 10 7.8 200W
DL4 800* 2400 43 10 7.8 300W
* 3P systems only 700N per DL4
Above measurements are made in connection with control box CBD4
R5
10
12
1
11
49.5
75
2.29°
5
Ø10
35
16

Speed and current curve
(measured with control box CBD4):
Load pr. leg
DESKPOWER DL4 Typical values DESKPOWER DL4 Guaranteed values
Speed
(mm/s)
60
40
20
0
0 200 400 600
800
Load (N)
Specifications subject to change without prior notice.
It is the responsibility of the product user to determine the suitability
of LINAK A/S products for a specific application. LINAK will at point of
delivery replace/repair defective products covered by the warranty
if promptly returned to the factory. No liability is assumed beyond
such replacement/repair.
Speed
(mm/s)
60
40
20
0
0 200 400 600
DESKPOWER DL4 Typical values DESKPOWER DL4 Guaranteed values
Speed
(mm/s)
60
40
20
0
0 200 400 600
60
40
20
0
800
Load (N)
0 200 400 600
DESKPOWER DL4 Typical values DESKPOWER DL4 Guaranteed values
Speed
(mm/s)
60
40
20
0
0 200 400 600
Speed
(mm/s)
Speed
(mm/s)
60
40
20
0
800
Load (N)
0 200 400 600
800
Load (N)
800
Load (N)
800
Load (N)
2 Parallel 200W
2 Parallel 300W
3 Parallel 300W
Copyright © LINAK 03.04 . MA M9-02-067-C . Chapter 14.14

CONTROL BOX CBD4
CBD4:
Features:
Mains voltage 120V AC, 230V AC, 50 – 60 Hz
Compact high power toroidal transformer
The control box is compatible with DL4, DL5, DL6 columns
and DB4, DB5, DB6 built-in actuators for single or parallel
drive
Compatible with controls DPA or DP1K or DP1U for memory
drive (3 positions)
Low power consumption in stand-by mode due to use of
toroidal transformer
Duty cycle max. 10 % ~ 6 min. per hour or 2 min. at
continuous use at full load
Colour: black
Exchangeable standard mains cable
Protection against overload (EOP), by individual current
limitation
The control box is designed with a soft start/stop function.
Hook for mains cable relief
Approved according to EN 60335-1 and to UL 73
Auto detection of the number of units for parallel drive
Auto detection of leg/unit type.
The CBD4 control box is the newest and most sophisticated
control box within the LINAK DESKLINE ® product range. The
CBD4 ensures that the DESKLINE application has a very low
and pleasant noise level and a constant speed level in the normal
use area. The control box is compatible with the columns
DL4, DL5, DL6 and the built-in actuators DB4, DB5, DB6. CBD4
ensures optimised parallel drive for 2, 3 or 4 legs in parallel or
a smooth drive as a single leg control box.

Dimensions:
100.6
119
62
Connection guidelines:
DPA
Ø5.5
DL/DB
Hook for cable relief
AC
Mains cable
278
247
3 2 1 B
The cable can both be placed to
the left or right on the DL4
5.5
80
51
Connection of the control and mains cable:
The control ( DPA, DP1U or DP1K ) is to be connected
on the same side of the control box as the lifting units.
On the advanced CBD4 there are 2 DP ports, which
both can be used.
Please note that the control box must only be connected to the voltage stated on the label.
Mounting abbreviations:
B = Control (DPA/DP1U)
AC = Connection to the mains
1-3 = sockets for DB or DL lifting units

CBD4
Ordering example:
CBD 4 P 0 0 0 2 0 0 - 0 0 9
Mains cables must be ordered separately.
Ordering number 015562 for the EU version
Ordering number 015942 for the US version
Class:
Mains cut-off:
Mains voltage:
9 = Class 2
Colour: -=Black
0
0
0 = Without mains cut-off
0=230V
1=120V
3 = 230V large transformer*
4 = 120V large transformer*
Channels: 2 = 2 Channels
3 = 3 Channels
4 = 4 Channels
0 Standard
0
0
Functionality:
Name: 4
Family: CBD
0 = Standard
A = Advanced concept
Standard
Standard
Standard
M = Single (will have 2 channels)
C = Parallel
H=4Parallel
P=2Parallel
* = Must always be chosen for 3 parallel systems and systems with DL5, DL6, DB5 and DB6
Mains cable:
The plug on the new exchangeable mains cable is smaller than on earlier standard cables. Together with a cable relief hook on
the CBD4 it ensures a stable cable connection.
Other mains cables (class II):
0015186 Coiled EU version, black, 0.6 m
0015193 Straight UK version, black, 3.2 m
0015239 Straight AUS version, black, 3.2 m
0015196 Straight EU version, grey, 3.2 m
0015197 Coiled EU version, grey, 0.6 m
3200 +/- 50

Specifications subject to change without prior notice.
It is the responsibility of the product user to determine the suitability
of LINAK A/S products for a specific application. LINAK will at point of
delivery replace/repair defective products covered by the warranty
if promptly returned to the factory. No liability is assumed beyond
such replacement/repair.
Copyright © LINAK 04.02 . MA M9-02-069-F . Chapter 20.4.1