8196446 - Frymaster

More documents

Recommendations

Info

1.16 BIELA14 Series LOV Data Network Flowchart 1-41
1.17 Interface Board Diagnostic Chart The following diagram and charts provide ten quick system checks that can be performed using only a multimeter. PN 826-2260 (106-6664) NOTE – Pin 1 is located in the bottom right corner of Both J1 and J2. These test points are ONLY for LOV Series boards with J1 and J2 plugs on the front of the board. Meter Setting Test Pin Pin Results 12 VAC Power 50 VAC Scale 3 of J2 1 of J2 12-16 VAC 24 VAC Power 50 VAC Scale 2 of J2 Chassis 24-30 VAC *Probe Resistance (RH) R X 1000 OHMS 11 of J2 10 of J2 See Chart *Probe Resistance (LH) R X 1000 OHMS 1 of J1 2 of J1 See Chart High-Limit Continuity (RH) R X 1 OHMS 9 of J2 6 of J2 0 - OHMS High-Limit Continuity (LH) R X 1 OHMS 6 of J1 9 of J1 0 - OHMS Latch Contactor Coil (RH) R X 1 OHMS 8 of J2 Chassis 3-10 OHMS Latch Contactor Coil (LH) R X 1 OHMS 5 of J1 Chassis 3-10 OHMS Heat Contactor Coil (RH) R X 1 OHMS 7 of J2 Chassis 11-15 OHMS Heat Contactor Coil (LH) R X 1 OHMS 4 of J1 Chassis 11-15 OHMS * Disconnect 15-Pin harness from the computer before testing the probe circuit. 1-42 Diagnostic LED Legend CMP indicates power from 12V transformer 24 indicates power from 24V transformer HI (RH) indicates output (closed) from right latch relay HI (LH) indicates output (closed) from left latch relay HT (RH) indicates output from right heat relay HT (LH) indicates output from left heat relay AL (RH) indicates output (open) from right latch relay AL (LH) indicates output (open) from left latch relay
Page 1 and 2: This equipment chapter is to be ins
Page 3 and 4: DANGER Improper installation, adjus
Page 5 and 6: • no fryer will be warranted unde
Page 7 and 8: BIELA14 SERIES GEN II LOV ELECTRIC
Page 9 and 10: 3. Remove the two screws from the u
Page 11 and 12: 4. Locate the red (or yellow) and w
Page 13 and 14: Full vat element wire routing 3 6 2
Page 15 and 16: 4. The contactors and relays are he
Page 17 and 18: 23. Position the element tube assem
Page 19 and 20: Disconnect flexlines indicated by t
Page 21 and 22: Problem Probable Causes Corrective
Page 23 and 24: 1.10.3 Replacing the ATO board, LON
Page 25 and 26: 1.11.2 MIB (Manual Interface Board)
Page 31 and 32: 1.12.2 RTI LOV Wiring 1.12.3 Frymas
Page 33 and 34: 8. “Filling” is displayed durin
Page 35 and 36: 1.13.2 AIF (Auto Intermittent Filtr
Page 37 and 38: 1.13.5 Replacing a Rotary Actuator
Page 39 and 40: Problem Probable Causes Corrective
Page 41 and 42: 1.14.3 Service Required Errors A SE
Page 43 and 44: 1.14.5 Tech Mode Tech mode allows t
Page 45 and 46: 1.14.7 M3000 Menu Summary Tree Refl
Page 47: 1.15 Loading and Updating Software
Page 51 and 52: 1.19 Wiring Diagrams 1.19.1 Compone
Page 53 and 54: 1.19.3 Component Wiring (CSA) 1-46
Page 55 and 56: 1.19.5 Contactor Box - Delta Config
Page 57 and 58: 1.19.7 Simplified BIELA14 LOV Gen I
Page 59 and 60: 1.19.9 Simplified BIELA14 LOV Gen I
Page 61 and 62: 1.19.11 BIELA14 Gen II Series LOV S
Page 63 and 64: 2.2 Doors, Sides, Tilt Housings, Ca
Page 65 and 66: 2.3.2 Drain Valves and Associated P
Page 67 and 68: 2.4.1 Component Boxes cont. ITEM PA
Page 69 and 70: 2.4.2.1 Left and Right Contactor Bo
Page 71 and 72: 2.4.3.1 Element Assemblies and Hard
Page 73 and 74: 2.4.3.2 Element Tube Assemblies con
Page 75 and 76: 2.4.5.3 Contactor Box Wiring Assemb
Page 77 and 78: 2.4.5.6 Component Box and Filter Pu
Page 79 and 80: 2.5 Filtration System Components 2.
Page 81 and 82: 2.5.2 Auto Intermittent Filtration
Page 83 and 84: 2.6 Frypot Assemblies and Associate
Page 85 and 86: 2.7 Oil Return Manifolds ITEM PART
Page 87 and 88: 2.9.2 JIB Cap and Pick Up Assembly
Page 89 and 90: 2.10 RTI 2.10.1 RTI Manifold and Ac
Page 91 and 92: 2.10.2 RTI Dispose Waste Valve ITEM
Page 93 and 94: 2.12 Fasteners ITEM PART # COMPONEN

8196446 - Frymaster

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?