Blaster CD 8x - Creative
Blaster CD 8x - Creative Blaster CD 8x - Creative
3. When Windows 95 starts, it automatically detects the new hardware in your system. Follow the on-screen instructions until the New Hardware Found dialog is displayed (Figure 2-1). Figure 2-1: New Hardware Found dialog. 4. Select the second driver option: “Driver from disk provided by hardware manufacturer.” 5. Choose OK. The Install From Disk dialog appears. Figure 2-2: Install From Disk dialog. 6. Insert the installation disk for the Blaster CD 8x into a floppy disk drive. 7. In the dialog text box, enter the letter for the floppy drive; for example, A:\ or B:\. Choose OK. The driver for the CD-ROM drive is copied to your computer. Follow the on-screen instructions to complete the installation. Installing the Blaster CD 8x Software 2-2
8. When the installation is complete, the System Settings Change dialog appears (Figure 2-3). Figure 2-3: System Settings Change dialog. 9. Choose No. Proceed to step 3 in the “Installing the CD-ROM Drive Software” section below. Installing the CD-ROM Drive Software To install the Blaster CD 8x software when connected to the hard disk controller, secondary IDE port, or non-PnP interface card: 1. After installing the Blaster CD 8x, replace the cover on your computer and reconnect the monitor and other devices. 2. Turn on the power to your computer. 3. When Windows 95 boots, choose the button on the task bar. The Start menu (Figure 2-4) is displayed. Figure 2-4: Start menu. Installing the Blaster CD 8x Software 2-3
- Page 1 and 2: Blaster CD 8x User Guide On-line Ve
- Page 3 and 4: Appendix A Troubleshooting CD-ROM D
- Page 5 and 6: Regulatory Information Notice for t
- Page 7 and 8: System Requirements Disk Backup To
- Page 9 and 10: . . . Ellipses indicate that the pr
- Page 11 and 12: Installing the CD-ROM Drive Figure
- Page 13 and 14: Connecting the CD-ROM Drive to the
- Page 15 and 16: Installing the Interface Card Use t
- Page 17 and 18: The data cable is designed to fit i
- Page 19 and 20: 2. Connect the CD-ROM audio cable t
- Page 21: 2 Installing the Blaster CD 8x Soft
- Page 25 and 26: 8. Choose Next. The Choose Destinat
- Page 27 and 28: 11. The Setup Complete dialog appea
- Page 29 and 30: Installing Software in DOS/Windows
- Page 31 and 32: Testing the Installation The test p
- Page 33 and 34: To add Windows QuickCD to Accessori
- Page 35 and 36: Using the Control Menu The Control
- Page 37 and 38: DOS QuickCD To run DOS QuickCD: Nex
- Page 39 and 40: Using the Mouse Place the mouse cur
- Page 41 and 42: Solutions: The problem may be corre
- Page 43 and 44: DOS Applications PROBLEM: There is
- Page 45 and 46: Using Creative IDE CD-ROM Drive in
- Page 47 and 48: MSCDEX.EXE Select the primary port
- Page 49 and 50: q You have changed the resource set
- Page 51 and 52: Legacy Cards Section Add Button Eac
- Page 53 and 54: Adding a CD-ROM Drive You can daisy
- Page 55 and 56: In DOS/Windows 3.x After connecting
- Page 57 and 58: Typical Audio Performance Sampling
- Page 59 and 60: North, Central, and South America I
8. When the installation is complete, the System Settings Change<br />
dialog appears (Figure 2-3).<br />
Figure 2-3: System Settings Change dialog.<br />
9. Choose No. Proceed to step 3 in the “Installing the <strong>CD</strong>-ROM<br />
Drive Software” section below.<br />
Installing the <strong>CD</strong>-ROM Drive Software<br />
To install the <strong>Blaster</strong> <strong>CD</strong> <strong>8x</strong> software when connected to the hard disk<br />
controller, secondary IDE port, or non-PnP interface card:<br />
1. After installing the <strong>Blaster</strong> <strong>CD</strong> <strong>8x</strong>, replace the cover on your<br />
computer and reconnect the monitor and other devices.<br />
2. Turn on the power to your computer.<br />
3. When Windows 95 boots, choose the button on the task<br />
bar. The Start menu (Figure 2-4) is displayed.<br />
Figure 2-4: Start menu.<br />
Installing the <strong>Blaster</strong> <strong>CD</strong> <strong>8x</strong> Software 2-3