0404 Owner's Manual - Creative
0404 Owner's Manual - Creative 0404 Owner's Manual - Creative
6 - Working with ASIO E-MU VST E-Wire Note concerning the Microsoft GS Wavetable Software Synth Use of the Microsoft GS Wavetable Software Synth will allow only 30 of the 32 ASIO playback channels to work properly. If your PatchMix session uses all 32 ASIO playback channels, you should disable the Microsoft SW Synth before using Cubase or Cubasis. 1. Go to: Start Menu, Programs, Steinberg, Setup MME. 2. Select Microsoft GS Wavetable SW Synth from the MME Outputs. 3. Click the Set Inactive button. 68 Creative Professional
7 - Appendix Sync Daughter Card Supplement SMPTE Conversion One of the main functions of the Sync Daughter Card is to convert SMPTE (LTC) to MIDI Time Code (MTC) and vice-versa. The term “Host MTC” refers to MTC, which is generated or used by the host application (Cubasis, Logic, etc.). MTC is also available at the MIDI jack on the back of the Sync Card. SMPTE Features • Conversion of SMPTE to MTC quarter-frame messages & full-frame messages. Constant quarter-frame messages are generated with steady SMPTE data input. Occasional MIDI full-frame messages are generated when SMPTE contains data dropouts. • Conversion of MTC (quarter frame & full frame) messages from the host computer to SMPTE out. Simultaneous SMPTE and MTC output when receiving MTC from the host computer • Outputs SMPTE and MTC striping data. SMPTE Start Time and type can be set via System Settings dialog box. SMPTE Options When the Sync Daughter Card installed in your system a SMPTE button in the PatchMix DSP mixer becomes visible. Pressing the SMPTE button brings up the SMPTE window. Current Time SMPTE Status/ Error Indicators Start Striping SMPTE Start Time SMPTE Frame Rate Settings Flywheel Mode • Off • Continuous • Fixed •1-time Jam Stop Striping Output Source Word Clock Termination Flywheel Amount Output Level 7 - Appendix Sync Daughter Card Supplement Warning: SMPTE and MTC do not provide sample sync for digital I/O. You must use Word Clock, or S/PDIF sync. E-MU Digital Audio System 69
- Page 25 and 26: Insert Section The Insert Section i
- Page 27 and 28: ASIO Direct Monitor Send/Return Thi
- Page 29 and 30: Meter Color Indicates E Red Indicat
- Page 31 and 32: Aux Section The Auxiliary Sends tap
- Page 33 and 34: Level, Pan, Solo & Mute Controls Th
- Page 35 and 36: TV Screen & Selectors The “TV scr
- Page 37 and 38: Auxiliary Effects & Returns The sec
- Page 39 and 40: 5 - Effects Overview PatchMix DSP c
- Page 41 and 42: Creating, Renaming & Deleting Folde
- Page 43 and 44: Method #2 1. Right-click over the E
- Page 45 and 46: Core Effects Descriptions 1-Band Pa
- Page 47 and 48: 4-Band EQ This 4-band equalizer pro
- Page 49 and 50: Chorus An audio delay in the range
- Page 51 and 52: Parameter Description Attack Time C
- Page 53 and 54: Freq Shifter This unusual effect is
- Page 55 and 56: Mono Delay 3000 A delay line makes
- Page 57 and 58: Speaker Simulator The Speaker Simul
- Page 59 and 60: Stereo Reverb Reverberation is a si
- Page 61 and 62: 6 - Working with ASIO ASIO ASIO sta
- Page 63 and 64: Basic Recording The following step
- Page 65 and 66: The Cubasis Demo Song Screen Inspec
- Page 67 and 68: Direct Monitoring Direct Monitor Se
- Page 69 and 70: Direct Monitor Routing In Cubasis (
- Page 71 and 72: Using External Sends & Returns An E
- Page 73 and 74: To Setup and use E-Wire: Setup Patc
- Page 75: E-Delay Units Parameter The Units v
- Page 79 and 80: Stripe Mode This mode is used to re
- Page 81 and 82: Duplicating SMPTE time code The Syn
- Page 83 and 84: S/PDIF Digital SYNC CARD ADAT Optic
- Page 85 and 86: Technical Specifications GENERAL Sa
- Page 87 and 88: Internet References The internet co
- Page 89 and 90: Compliance Information United State
- Page 91 and 92: Index Numerics 1-Band Para EQ 37 1-
- Page 93 and 94: fader 25 insert 17 label 25 mute bu
6 - Working with ASIO<br />
E-MU VST E-Wire<br />
Note concerning the Microsoft GS Wavetable Software Synth<br />
Use of the Microsoft GS Wavetable Software Synth will allow only 30 of the 32 ASIO<br />
playback channels to work properly. If your PatchMix session uses all 32 ASIO playback<br />
channels, you should disable the Microsoft SW Synth before using Cubase or Cubasis.<br />
1. Go to: Start Menu, Programs, Steinberg, Setup MME.<br />
2. Select Microsoft GS Wavetable SW Synth from the MME Outputs.<br />
3. Click the Set Inactive button.<br />
68 <strong>Creative</strong> Professional
Change language