0404 Owner's Manual - Creative

More documents

Recommendations

Info

2 - Installation Installing the E-MU 0404 PCI Card Connector Types These connector types are used to connect the E-MU 0404 hardware components. They will be referred to by the name shown in the first column of the following chart: Installing the E-MU 0404 PCI Card Note: This installation is very simple, but if you are not familiar with the installation of computer peripherals and add-in boards, please contact your authorized E-MU Systems dealer or an approved computer service center to arrange for the installation. 1. 2. 3. 4. 5. Name Description Connects DB-15 Digital Digital Cable Connector 0404 PCI card and Digital I/O DB-9 Analog Analog Cable Connector 0404 PCI card and Analog I/O 1/4” Jacks 1/4” Breakout Cable 2 channel analog input/output S/PDIF In RCA Connector S/PDIF digital audio devices S/PDIF Out RCA Connector S/PDIF digital audio devices S/PDIF Optical In TOSLINK Optical Connector S/PDIF digital audio devices S/PDIF Optical Out TOSLINK Optical Connector S/PDIF digital audio devices To install the 0404 PCI card into your computer Make sure that the power switch on your computer is off. Touch a metal plate on your computer to ground yourself and to discharge any static electricity. IMPORTANT: Unplug the power cord from the wall outlet! Follow the computer manufacturer’s recommended procedure for opening the case. Remove the metal bracket from any available PCI slot. If you are installing a Sync Card as well, remove the bracket from two adjacent PCI slots. See figure 1 below. Figure 1 Figure 2 (may not be present on your computer) ISA Slots PCI Slots Align the E-MU 0404 PCI card with the slot and press gently but firmly down into the slot as shown in figure 2. E Note: Some computer cases don’t use screws to secure PCI cards. In this case, follow the instructions that came with your computer. 2 Creative Professional
6. 7. 8. 9. Do not force the E-MU 0404 card into the slot. Make sure that the gold finger connector of the card is aligned with the PCI bus connector on the motherboard before you insert the card into the PCI slot. If it doesn’t fit properly, gently remove it and try again. Secure the card into the slot using one of the screws you placed aside earlier. Attach the Analog and Digital breakout cables to the rear of the 0404 card. Connect your audio cables to the breakout cables. Install the Sync Card 1. 2. 3. 4. 5. Unwrap the Sync Card if you have one and get ready to install it. Connect the ribbon cable provided with the kit between the E-MU 0404 card and the Sync Daughter Card as shown in figure 3. The cable is keyed so it cannot be incorrectly inserted. Seat the connectors firmly in the sockets and arrange the cable neatly. Align the Sync Card with the slot and press gently but firmly down into the slot as shown in figure 2 on the preceding page. Do not force the Sync Card into the slot. Make sure that the gold finger connector of the card is aligned with the PCI bus connector on the motherboard before you insert the card into the PCI slot. If it doesn’t fit properly, gently remove it and try again. Secure the card into the slot using one of the screws you placed aside earlier. Figure 3 Sync Daughter Card 2 - Installation Install the Sync Card E-MU Digital Audio System 3
Page 1 and 2: 0404 Digital Audio System Owner's M
Page 3 and 4: Table of Contents 1- Introduction .
Page 5 and 6: Freq Shifter ......................
Page 7 and 8: 1- Introduction Welcome! Thank you
Page 9: 2 - Installation Setting Up the Dig
Page 13 and 14: 3 - PCI Card & Interfaces The E-MU
Page 15 and 16: The S/PDIF out can be configured as
Page 17 and 18: 4 - The PatchMix DSP Mixer PatchMix
Page 19 and 20: The Toolbar New Session Open Sessio
Page 21 and 22: You can now create either a blank n
Page 23 and 24: Input Mixer Strips PatchMix DSP Lin
Page 25 and 26: Insert Section The Insert Section i
Page 27 and 28: ASIO Direct Monitor Send/Return Thi
Page 29 and 30: Meter Color Indicates E Red Indicat
Page 31 and 32: Aux Section The Auxiliary Sends tap
Page 33 and 34: Level, Pan, Solo & Mute Controls Th
Page 35 and 36: TV Screen & Selectors The “TV scr
Page 37 and 38: Auxiliary Effects & Returns The sec
Page 39 and 40: 5 - Effects Overview PatchMix DSP c
Page 41 and 42: Creating, Renaming & Deleting Folde
Page 43 and 44: Method #2 1. Right-click over the E
Page 45 and 46: Core Effects Descriptions 1-Band Pa
Page 47 and 48: 4-Band EQ This 4-band equalizer pro
Page 49 and 50: Chorus An audio delay in the range
Page 51 and 52: Parameter Description Attack Time C
Page 53 and 54: Freq Shifter This unusual effect is
Page 55 and 56: Mono Delay 3000 A delay line makes
Page 57 and 58: Speaker Simulator The Speaker Simul
Page 59 and 60: Stereo Reverb Reverberation is a si
Page 61 and 62:
6 - Working with ASIO ASIO ASIO sta
Page 63 and 64:
Basic Recording The following step
Page 65 and 66:
The Cubasis Demo Song Screen Inspec
Page 67 and 68:
Direct Monitoring Direct Monitor Se
Page 69 and 70:
Direct Monitor Routing In Cubasis (
Page 71 and 72:
Using External Sends & Returns An E
Page 73 and 74:
To Setup and use E-Wire: Setup Patc
Page 75 and 76:
E-Delay Units Parameter The Units v
Page 77 and 78:
7 - Appendix Sync Daughter Card Sup
Page 79 and 80:
Stripe Mode This mode is used to re
Page 81 and 82:
Duplicating SMPTE time code The Syn
Page 83 and 84:
S/PDIF Digital SYNC CARD ADAT Optic
Page 85 and 86:
Technical Specifications GENERAL Sa
Page 87 and 88:
Internet References The internet co
Page 89 and 90:
Compliance Information United State
Page 91 and 92:
Index Numerics 1-Band Para EQ 37 1-
Page 93 and 94:
fader 25 insert 17 label 25 mute bu
show all

0404 Owner's Manual - Creative

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?