en 0017 4002 05 - Atlas Copco
en 0017 4002 05 - Atlas Copco en 0017 4002 05 - Atlas Copco
1 GENERAL Airpower Standards Department © TECHNICAL SPECIFICATION Datum/Date Uitgave/Edition en 0017 4002 05 Bladzjde/Page 2010-04-16 1 1(2) Surface treatment - Paints AC YELLOW POLYESTER POWDER Article number 0017 4002 05 This standard specifies the above-stated article, from the database Liquids and semi-solids - GSD (Lotus Notes). This survey of paint description and specifications is based on instructions given out by Atlas Copco Airpower n.v. Wilrijk. Reference to this standard has to be made by mentioning the number at the upper right hand corner. Safety instructions of the mentioned products can be found on the GSD web application Chemical Handling. 2 PAINT DESCRIPTION A.C. material number : 0017 4002 05 Approved supplier paint codes : Akzo OE 751F Colour acc. to reference sheet : Yellow Paint type : polyester, powder 3 SPECIFICATIONS Film thickness (acc. to EN ISO 2178) : 80-120, measured on min 10 spots Tests: - gloss - Gardner 60° : 60 +/-5 % - hardness persoz (Pendell 12-6°) : min 250 s - Adhesion (DIN en ISO 2409) : Gt 0 - 1 - Conical spine (ISO 6860) : bursts at max 30mm - impact direct (ISO 6272) : 25kg.cm - resistance against corrosion -water immersion (ASTM D 870 - 87) : 500 h: no peeling off or infiltration -humidity Room (DIN50017) : 500 h: no blisters, adhesion Gt 0-1 - salt spray (ASTM B 117 - 85) : 500 h: no blisters, adhesion Gt 0-1 infiltration in edges : 0 Rust : not allowed - Kesternich test (DIN 50018 SFW2.OS): adhesion Gt 0-1 (after min. 7 cycli) no rust in plate - Max Change of colour : ∆E=1.25; ∆L=0.5; ∆a=0.8; ∆b=0.8 - filiformcorrosion : 24 h salt spray, afterwards 1 week in clima room at 24°C and 85% relative humidity; no undercreep - chemical resistance - products loss of gloss ∆G =max 10% 1. Paroil M max change of color: 2. Paroil S ∆E=1.25; ∆L=0.5; ∆a=0.8; ∆b=0.8 3. 15W40 adhesion: unchanged 4. 5W30 hardness Persoz : unchanged
1 GENERAL<br />
Airpower<br />
Standards<br />
Departm<strong>en</strong>t ©<br />
TECHNICAL<br />
SPECIFICATION<br />
Datum/Date Uitgave/Edition<br />
<strong>en</strong> <strong>0017</strong> <strong>4002</strong> <strong>05</strong><br />
Bladzjde/Page<br />
2010-04-16 1<br />
1(2)<br />
Surface treatm<strong>en</strong>t - Paints<br />
AC YELLOW POLYESTER POWDER<br />
Article number <strong>0017</strong> <strong>4002</strong> <strong>05</strong><br />
This standard specifies the above-stated article, from the database Liquids and semi-solids - GSD (Lotus Notes).<br />
This survey of paint description and specifications is based on instructions giv<strong>en</strong> out by <strong>Atlas</strong><br />
<strong>Copco</strong> Airpower n.v. Wilrijk.<br />
Refer<strong>en</strong>ce to this standard has to be made by m<strong>en</strong>tioning the number at the upper right hand<br />
corner. Safety instructions of the m<strong>en</strong>tioned products can be found on the GSD web application<br />
Chemical Handling.<br />
2 PAINT DESCRIPTION<br />
A.C. material number : <strong>0017</strong> <strong>4002</strong> <strong>05</strong><br />
Approved supplier paint codes : Akzo OE 751F<br />
Colour acc. to refer<strong>en</strong>ce sheet : Yellow<br />
Paint type : polyester, powder<br />
3 SPECIFICATIONS<br />
Film thickness (acc. to EN ISO 2178) : 80-120, measured on min 10 spots<br />
Tests:<br />
- gloss - Gardner 60° : 60 +/-5 %<br />
- hardness persoz (P<strong>en</strong>dell 12-6°) : min 250 s<br />
- Adhesion (DIN <strong>en</strong> ISO 2409) : Gt 0 - 1<br />
- Conical spine (ISO 6860) : bursts at max 30mm<br />
- impact direct (ISO 6272) : 25kg.cm<br />
- resistance against corrosion<br />
-water immersion (ASTM D 870 - 87) : 500 h: no peeling off or infiltration<br />
-humidity Room (DIN5<strong>0017</strong>) : 500 h: no blisters, adhesion Gt 0-1<br />
- salt spray (ASTM B 117 - 85) : 500 h: no blisters, adhesion Gt 0-1<br />
infiltration in edges : 0<br />
Rust : not allowed<br />
- Kesternich test (DIN 50018 SFW2.OS): adhesion Gt 0-1<br />
(after min. 7 cycli) no rust in plate<br />
- Max Change of colour : ∆E=1.25; ∆L=0.5; ∆a=0.8; ∆b=0.8<br />
- filiformcorrosion : 24 h salt spray, afterwards 1 week in clima room at 24°C and<br />
85% relative humidity; no undercreep<br />
- chemical resistance<br />
- products loss of gloss ∆G =max 10%<br />
1. Paroil M max change of color:<br />
2. Paroil S ∆E=1.25; ∆L=0.5; ∆a=0.8; ∆b=0.8<br />
3. 15W40 adhesion: unchanged<br />
4. 5W30 hardness Persoz : unchanged
.Edition check<br />
- Lotus Notes data base Standard Docum<strong>en</strong>ts - GSD<br />
- Internet URL http://atlascopco.com/gsd<br />
Airpower<br />
Standards<br />
Departm<strong>en</strong>t ©<br />
TECHNICAL<br />
SPECIFICATION<br />
Datum/Date Uitgave/Edition<br />
<strong>en</strong> <strong>0017</strong> <strong>4002</strong> <strong>05</strong><br />
Bladzjde/Page<br />
2010-04-16 1<br />
2(2)<br />
5. Parcool<br />
6. Diesel<br />
- outdoor exposition<br />
after 1 year at <strong>Atlas</strong> <strong>Copco</strong> Portable Air<br />
1. infiltration in edges : 0 !<br />
2. infiltration of the cross : 0, no undercreep allowed<br />
3. rust : not allowed<br />
4. loss of gloss : ∆G =max 10%<br />
5. max change of color : ∆E=1.25; ∆L=0.5; ∆a=0.8; ∆b=0.8<br />
4 ARTICLE NAME<br />
.<br />
Note: Max. 15 characters (spaces included).<br />
<strong>en</strong> Paint es Pintura nl Verf<br />
sv Färg fr Peinture de Farbe<br />
Type C2: Finishing paint – powder paint type.
Change language