M12 Oncore Users Guide Supplement - deetc - isel
M12 Oncore Users Guide Supplement - deetc - isel M12 Oncore Users Guide Supplement - deetc - isel
Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 GPGSA (GPS DOP AND ACTIVE SATELLITES) This command enables the GPGSA GPS DOP and Active Satellites message and determines the rate at which the information is transmitted. The periodic rate field (yyyy) instructs the receiver either to output this message once (polled), or to output this message at the indicated update rate (continuously). Once the receiver is set to continuous output, the continuous flow can be stopped by sending a one-time (polled) output request. The receiver will output the response one final time, and then terminate any further message outputs. The value of the periodic rate is retained through a power cycle only if battery backup power is applied. If the receiver is not computing a position fix (mode field (b) is one), then the xDOP fields (p.p, q.q, r.r) will be nulled. If the receiver is computing a 2-D position fix (mode field (b) is two), then the PDOP field (p.p) and the VDOP field (r.r) will be nulled. Only satellite IDs used in the solution are output; the remaining satellite ID fields will be nulled. Default mode: Disabled 98
Input Command Response Message Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 GPGSA (GPS DOP AND ACTIVE SATELLITES) NMEA-0183 Format • Set response message rate: $PMOTG,GSA,yyyyCC yyyy update rate 0 .. 9999 seconds CC optional checksum • To above command: $GPGSA,a,b,cc,dd,ee,ff,gg,hh,ii,jj,kk,mm,nn,oo, p.p,q.q,r.r*CC a sat acquisition mode M = manual (forced to operate in 2D or 3D mode) A = automatic (auto switch 2D/3D) b positioning mode 1 = fix not available 2 = 2D 3 = 3D cc, dd, ee, ff, gg, hh, ii, jj, kk, SVIDs used in solution (null for unused fields) mm, nn, oo p.p PDOP 1.0 .. 9.9 q.q HDOP 1.0 .. 9.9 r.r VDOP 1.0 .. 9.9 CC checksum 99
- Page 47 and 48: Input Command Response Message Moto
- Page 49 and 50: Input Command Response Message Moto
- Page 51 and 52: Input Command Response Message Moto
- Page 53 and 54: Input Command Response Message Moto
- Page 55 and 56: Input Command Response Message Moto
- Page 57 and 58: Input Command Response Message Moto
- Page 59 and 60: Input Command Response Message Moto
- Page 61 and 62: Input Command Response Message Moto
- Page 63 and 64: Input Command Response Message @ #
- Page 65 and 66: Input Command Response Message Moto
- Page 67 and 68: Input Command Response Message Moto
- Page 69 and 70: Input Command Response Message Moto
- Page 71 and 72: Input Command Response Message Moto
- Page 73 and 74: Input Command Response Message Moto
- Page 75 and 76: Input Command Response Message Moto
- Page 77 and 78: Input Command Response Message Moto
- Page 79 and 80: Input Command Response Message Moto
- Page 81 and 82: Input Command Response Message Moto
- Page 83 and 84: Response Message (Continued) Motoro
- Page 85 and 86: Motorola GPS Products M12 Oncore Us
- Page 87 and 88: Input Command Response Message Moto
- Page 89 and 90: Motorola GPS Products M12 Oncore Us
- Page 91 and 92: Input Command Response Message Moto
- Page 93 and 94: Output Command Motorola GPS Product
- Page 95 and 96: Input Command Response Message Moto
- Page 97: Input Command GPGLL (GEOGRAPHIC POS
- Page 101 and 102: Input Command Response Message Moto
- Page 103 and 104: Input Command Response Message Moto
- Page 105 and 106: Input Command Response Message Moto
- Page 107 and 108: Input Command Response Message Moto
- Page 109 and 110: Input Command Response Message Moto
- Page 111 and 112: Satellite Mask Angle Function Contr
- Page 113 and 114: Position-Hold Position Function Inp
- Page 115 and 116: RTCM Port Mode Function Sets the ba
- Page 117 and 118: Almanac Data Output Function Output
- Page 119 and 120: Almanac Data Input Function Manuall
- Page 121 and 122: ASCII Position Output Function The
- Page 123 and 124: Position Control Function Sets the
- Page 125 and 126: Oscillator Learning Function Reques
- Page 127 and 128: Controller ID cid Run Command run M
Input Command<br />
Response Message<br />
Motorola GPS Products<br />
<strong>M12</strong> <strong>Oncore</strong> User’s <strong>Guide</strong> <strong>Supplement</strong><br />
Revision 1.0 01/25/00<br />
GPGSA (GPS DOP AND ACTIVE SATELLITES)<br />
NMEA-0183 Format<br />
• Set response message rate:<br />
$PMOTG,GSA,yyyyCC<br />
yyyy update rate 0 .. 9999 seconds<br />
CC optional checksum<br />
• To above command:<br />
$GPGSA,a,b,cc,dd,ee,ff,gg,hh,ii,jj,kk,mm,nn,oo,<br />
p.p,q.q,r.r*CC<br />
a sat acquisition mode M = manual (forced to operate in 2D or 3D mode)<br />
A = automatic (auto switch 2D/3D)<br />
b positioning mode 1 = fix not available<br />
2 = 2D<br />
3 = 3D<br />
cc, dd, ee,<br />
ff, gg, hh,<br />
ii, jj, kk,<br />
SVIDs used in solution (null for unused fields)<br />
mm, nn, oo<br />
p.p PDOP 1.0 .. 9.9<br />
q.q HDOP 1.0 .. 9.9<br />
r.r VDOP 1.0 .. 9.9<br />
CC checksum<br />
99