M12 Oncore Users Guide Supplement - deetc - isel
M12 Oncore Users Guide Supplement - deetc - isel M12 Oncore Users Guide Supplement - deetc - isel
Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 SYSTEM POWER-ON FAILURE Immediately after power-up, the Oncore’s ROM is tested. If this test does not pass, the Oncore firmware will not execute its positioning algorithms. Rather, it will continuously output this message at a 10 second rate. Receipt of this message indicates that the receiver will need to be repaired and/or reprogrammed. This feature keeps the receiver from being utilized when the ROM is, for some reason, compromised and therefore, unreliable. This feature helps to protect the integrity of the application. 92
Output Command Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 SYSTEM POWER-ON FAILURE Motorola Binary Format @@SzcC c constant equal to 0 C checksum Message length: 8 bytes 93
- Page 41 and 42: Input Command Response Message Moto
- Page 43 and 44: Input Command Response Message Moto
- Page 45 and 46: Input Command Response Message Moto
- Page 47 and 48: Input Command Response Message Moto
- Page 49 and 50: Input Command Response Message Moto
- Page 51 and 52: Input Command Response Message Moto
- Page 53 and 54: Input Command Response Message Moto
- Page 55 and 56: Input Command Response Message Moto
- Page 57 and 58: Input Command Response Message Moto
- Page 59 and 60: Input Command Response Message Moto
- Page 61 and 62: Input Command Response Message Moto
- Page 63 and 64: Input Command Response Message @ #
- Page 65 and 66: Input Command Response Message Moto
- Page 67 and 68: Input Command Response Message Moto
- Page 69 and 70: Input Command Response Message Moto
- Page 71 and 72: Input Command Response Message Moto
- Page 73 and 74: Input Command Response Message Moto
- Page 75 and 76: Input Command Response Message Moto
- Page 77 and 78: Input Command Response Message Moto
- Page 79 and 80: Input Command Response Message Moto
- Page 81 and 82: Input Command Response Message Moto
- Page 83 and 84: Response Message (Continued) Motoro
- Page 85 and 86: Motorola GPS Products M12 Oncore Us
- Page 87 and 88: Input Command Response Message Moto
- Page 89 and 90: Motorola GPS Products M12 Oncore Us
- Page 91: Input Command Response Message Moto
- Page 95 and 96: Input Command Response Message Moto
- Page 97 and 98: Input Command GPGLL (GEOGRAPHIC POS
- Page 99 and 100: Input Command Response Message Moto
- Page 101 and 102: Input Command Response Message Moto
- Page 103 and 104: Input Command Response Message Moto
- Page 105 and 106: Input Command Response Message Moto
- Page 107 and 108: Input Command Response Message Moto
- Page 109 and 110: Input Command Response Message Moto
- Page 111 and 112: Satellite Mask Angle Function Contr
- Page 113 and 114: Position-Hold Position Function Inp
- Page 115 and 116: RTCM Port Mode Function Sets the ba
- Page 117 and 118: Almanac Data Output Function Output
- Page 119 and 120: Almanac Data Input Function Manuall
- Page 121 and 122: ASCII Position Output Function The
- Page 123 and 124: Position Control Function Sets the
- Page 125 and 126: Oscillator Learning Function Reques
- Page 127 and 128: Controller ID cid Run Command run M
Output Command<br />
Motorola GPS Products<br />
<strong>M12</strong> <strong>Oncore</strong> User’s <strong>Guide</strong> <strong>Supplement</strong><br />
Revision 1.0 01/25/00<br />
SYSTEM POWER-ON FAILURE<br />
Motorola Binary Format<br />
@@SzcC<br />
c constant equal to 0<br />
C checksum<br />
Message length: 8 bytes<br />
93