M12 Oncore Users Guide Supplement - deetc - isel
M12 Oncore Users Guide Supplement - deetc - isel M12 Oncore Users Guide Supplement - deetc - isel
Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 TIME MODE This command selects the type of time (either GPS or UTC) to be output in the Position/Status/Data and Short Position Messages. The Time Mode command will be used to determine the synchronization point for the 1PPS timing pulse. Note that if the receiver does not have the UTC parameters portion of the almanac, UTC will be output as being equal to GPS time and a flag denoting the lack of UTC parameters will be set in the Position/Status/Data message (@@Ha). The receiver will have the UTC parameters once an almanac has been downloaded from the satellites. Default mode: UTC 28
Input Command Response Message Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 TIME MODE Motorola Binary Format • Poll current Time Mode: @@AwxC x 1 out of range byte $ff C checksum Message length: 8 bytes • Change current Time Mode: @@AwmC m mode 0 = GPS 1 = UTC C checksum Message length: 8 bytes • To either command: @@AwmC m mode 0 = GPS 1 = UTC C checksum Message length: 8 bytes 29
- Page 1 and 2: M12 User’s Guide Supplement
- Page 3 and 4: General Characteristics Performance
- Page 5 and 6: 3. Mechanical 3.1 Mechanical Drawin
- Page 7 and 8: 5.2 Main power Motorola GPS Product
- Page 9 and 10: 8. Performance 8.1 Accuracy Motorol
- Page 11 and 12: 10. Serial I/O Messages 10.1 Soluti
- Page 13 and 14: Motorola GPS Products M12 Oncore Us
- Page 15 and 16: Input Command Response Message Moto
- Page 17 and 18: Input Command SATELLITE IGNORE LIST
- Page 19 and 20: Input Command Response Message Moto
- Page 21 and 22: Input Command Response Message Moto
- Page 23 and 24: Input Command Response Message Moto
- Page 25 and 26: Input Command POSITION-HOLD POSITIO
- Page 27: Input Command Response Message Moto
- Page 31 and 32: Input Command Response Message Moto
- Page 33 and 34: Input Command Response Message Moto
- Page 35 and 36: Input Command Response Message Moto
- Page 37 and 38: Input Command Response Message Moto
- Page 39 and 40: Input Command Response Message Moto
- Page 41 and 42: Input Command Response Message Moto
- Page 43 and 44: Input Command Response Message Moto
- Page 45 and 46: Input Command Response Message Moto
- Page 47 and 48: Input Command Response Message Moto
- Page 49 and 50: Input Command Response Message Moto
- Page 51 and 52: Input Command Response Message Moto
- Page 53 and 54: Input Command Response Message Moto
- Page 55 and 56: Input Command Response Message Moto
- Page 57 and 58: Input Command Response Message Moto
- Page 59 and 60: Input Command Response Message Moto
- Page 61 and 62: Input Command Response Message Moto
- Page 63 and 64: Input Command Response Message @ #
- Page 65 and 66: Input Command Response Message Moto
- Page 67 and 68: Input Command Response Message Moto
- Page 69 and 70: Input Command Response Message Moto
- Page 71 and 72: Input Command Response Message Moto
- Page 73 and 74: Input Command Response Message Moto
- Page 75 and 76: Input Command Response Message Moto
- Page 77 and 78: Input Command Response Message Moto
Motorola GPS Products<br />
<strong>M12</strong> <strong>Oncore</strong> User’s <strong>Guide</strong> <strong>Supplement</strong><br />
Revision 1.0 01/25/00<br />
TIME MODE<br />
This command selects the type of time (either GPS or UTC) to be output in the<br />
Position/Status/Data and Short Position Messages. The Time Mode command will be used to<br />
determine the synchronization point for the 1PPS timing pulse.<br />
Note that if the receiver does not have the UTC parameters portion of the almanac, UTC will<br />
be output as being equal to GPS time and a flag denoting the lack of UTC parameters will be<br />
set in the Position/Status/Data message (@@Ha).<br />
The receiver will have the UTC parameters once an almanac has been downloaded from the<br />
satellites.<br />
Default mode: UTC<br />
28