M12 Oncore Users Guide Supplement - deetc - isel

More documents

Recommendations

Info

Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 SATELLITE IGNORE LIST It is useful to have the flexibility to delete particular satellite identification numbers (SVIDs) from the selection process. The GPS receiver includes, in its list of satellites to track, all satellites that are healthy and in the almanac. The user can elect to ignore particular satellites in the almanac by issuing an Ignore Satellite Command. In addition, the user can restore any previously ignored satellite IDs by issuing an Include Satellite Command. This command also affects the satellite Alert-Planning settings. Satellites that have been removed by this command are not included in the produced Alert-Planning output. The user may notice a delay between issuing this command and the actual removal or inclusion of particular satellites. Default value: All satellite SVIDs included. 16
Input Command SATELLITE IGNORE LIST Motorola Binary Format Response Message Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 • Send Current Satellite Ignore List: @@AmxxxxxC xxxxx 5 bytes all hex 00 C checksum Message Length: 12 bytes • Change Satellite Ignore List: @@AmkssssC k 00 fixed binary constant ssss 32 bit binary field. Each bit represents one SVID. (msb = SVID 32, lsb = SVID 1) 1 = Ignore 0 = Include C checksum Message Length: 12 bytes • To either command: @@AmkssssC k 00 fixed binary constant ssss 32 bit binary field. Each bit represents one SVID. (msb = SVID 32, lsb = SVID 1) 1 = Ignore 0 = Include C checksum Message Length: 12 bytes 17
Page 1 and 2: M12 User’s Guide Supplement
Page 3 and 4: General Characteristics Performance
Page 5 and 6: 3. Mechanical 3.1 Mechanical Drawin
Page 7 and 8: 5.2 Main power Motorola GPS Product
Page 9 and 10: 8. Performance 8.1 Accuracy Motorol
Page 11 and 12: 10. Serial I/O Messages 10.1 Soluti
Page 13 and 14: Motorola GPS Products M12 Oncore Us
Page 15: Input Command Response Message Moto
Page 19 and 20: Input Command Response Message Moto
Page 25 and 26: Input Command POSITION-HOLD POSITIO
Page 63 and 64: Input Command Response Message @ #
Page 67 and 68:
Input Command Response Message Moto
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Response Message (Continued) Motoro
Page 85 and 86:
Motorola GPS Products M12 Oncore Us
Page 87 and 88:
Page 89 and 90:
Motorola GPS Products M12 Oncore Us
Page 91 and 92:
Page 93 and 94:
Output Command Motorola GPS Product
Page 95 and 96:
Page 97 and 98:
Input Command GPGLL (GEOGRAPHIC POS
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Satellite Mask Angle Function Contr
Page 113 and 114:
Position-Hold Position Function Inp
Page 115 and 116:
RTCM Port Mode Function Sets the ba
Page 117 and 118:
Almanac Data Output Function Output
Page 119 and 120:
Almanac Data Input Function Manuall
Page 121 and 122:
ASCII Position Output Function The
Page 123 and 124:
Position Control Function Sets the
Page 125 and 126:
Oscillator Learning Function Reques
Page 127 and 128:
Controller ID cid Run Command run M
show all

M12 Oncore Users Guide Supplement - deetc - isel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?