M12 Oncore Users Guide Supplement - deetc - isel

More documents

Recommendations

Info

Combined Time Function Changes the current date, time and GMT offset of the comtim 12 Channel Oncore receiver. If the date or time is not specified, this command requests that the receiver output the current date and time. Syntax comtim (MM DD YY hh mm ss [ - | + | ] hh mm) MM month DD day YY year hh hour mm minutes ss seconds hh hour of GMT offset mm minute of GMT offset Example comtim 9 29 00 23 23 23 –7 0 date 9/29/2000 time 23:23:23 GMT Offset -7:00 hours Notes If the receiver has acquired at least one satellite, the receiver ignores the changed time and date and responds with the current time and date. The receiver output time is either GMT or local time, depending on the setting of the GMT offset parameter. See Also None Binary Equivalent @@Gb 1PPS Control Function Controls how the 1PPS output in the receiver will behave. ppscon Syntax ppscon ([ 0 | 1 | 2 ]) 0 = 1PPS disabled 1 = 1PPS on continuously 2 = pulse active only when tracking at least one satellite Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 COMMAND DESCRIPTIONS Example ppscon 1 Notes None See Also None Binary Equivalent @@Gc 122
Position Control Function Sets the positioning mode for the receiver. holdcon Syntax holdcon ([ 0 | 1 | 2 |) 0 = no hold or normal positioning 1 = enable position hold 2 = enable altitude hold Example holdcon 1 Notes None See Also None Binary Equivalent @@Gd Leap Second Pending Function Used to determine if there is a pending leap second correction leap12 Syntax leap12 Example leap12 Notes This is a polled-only output message. If a correction is pending, the direction of the correction is indicated. See Also None Binary Equivalent @@Gj ID Tag Function Sets or defaults the ID tag. vin Syntax vin ([ ++++++ ]) ++++++ ID tag will be receiver serial number 6 spaces No change Motorola GPS Products M12 Oncore User’s Guide Supplement Revision 1.0 01/25/00 COMMAND DESCRIPTIONS Example vin ++++++ Notes None Any other combination of 6 ASCII characters (from 0x20 to 0x7e0will be construed as a new ID tag. Any out of range character will cause the ID tag to remain unchanged. See Also Position/Status/Data Message (@@Ha) Binary Equivalent @@Gk 123
Page 1 and 2:
M12 User’s Guide Supplement
Page 3 and 4:
General Characteristics Performance
Page 5 and 6:
3. Mechanical 3.1 Mechanical Drawin
Page 7 and 8:
5.2 Main power Motorola GPS Product
Page 9 and 10:
8. Performance 8.1 Accuracy Motorol
Page 11 and 12:
10. Serial I/O Messages 10.1 Soluti
Page 13 and 14:
Motorola GPS Products M12 Oncore Us
Page 15 and 16:
Input Command Response Message Moto
Page 17 and 18:
Input Command SATELLITE IGNORE LIST
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Input Command POSITION-HOLD POSITIO
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Input Command Response Message @ #
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72: Input Command Response Message Moto
Page 83 and 84: Response Message (Continued) Motoro
Page 85 and 86: Motorola GPS Products M12 Oncore Us
Page 89 and 90: Motorola GPS Products M12 Oncore Us
Page 93 and 94: Output Command Motorola GPS Product
Page 97 and 98: Input Command GPGLL (GEOGRAPHIC POS
Page 111 and 112: Satellite Mask Angle Function Contr
Page 113 and 114: Position-Hold Position Function Inp
Page 115 and 116: RTCM Port Mode Function Sets the ba
Page 117 and 118: Almanac Data Output Function Output
Page 119 and 120: Almanac Data Input Function Manuall
Page 121: ASCII Position Output Function The
Page 125 and 126: Oscillator Learning Function Reques
Page 127 and 128: Controller ID cid Run Command run M
show all

M12 Oncore Users Guide Supplement - deetc - isel

Create successful ePaper yourself

Delete template?

Save as template?