Back-UPS® - APC Media
Back-UPS® - APC Media Back-UPS® - APC Media
3.0 Installation 3.7 Test for proper operation - continued cord. Observe that your equipment operates normally during both transfer from utility power to UPS power and back again. Repeat this test four or five times to ensure proper operation. See the following section covering Overloads if abnormal operation is encountered. The power I/0 control switches power to your equipment. If you leave your equipment power switches on, the I/0 power control can be used as a master on/ off switch! 3.8 Overloads If the total power requirement of your equipment is much greater than the capacity of the UPS, the UPS’s rear panel circuit breaker may trip. This is called an overload situation. Once the circuit breaker trips, the UPS will attempt to operate the load using its internal power source. This may result in an unexpectedly short run time or, if the overload is severe, the UPS will immediately shut down and cease to power the load. In this case, the UPS will emit a loud tone to alert you of the overload. If this occurs during your test, turn off the UPS and decide which equipment will be left unprotected by the UPS. The circuit breaker may be reset (press button) when the overload is removed. Page 12
4.0 Principles of operation Below is a block diagram showing the major components of your UPS. These blocks are described on the following pages. Block diagram showing all major components of your UPS. Page 13
- Page 1 and 2: Back-UPS ® Models 250, 400 and 600
- Page 3 and 4: Table of contents 1.0 Introduction.
- Page 5 and 6: 2.0 Safety ! ENGLISH ■ To reduce
- Page 7 and 8: 2.0 Sicherheit ! DEUTSCH ■ Um die
- Page 9 and 10: 3.0 Installation 3.1 Receiving insp
- Page 11 and 12: 3.0 Installation 3.6 Connecting you
- Page 13: 3.0 Installation 3.6 Connecting you
- Page 17 and 18: 4.0 Principles of operation 4.2 Loa
- Page 19 and 20: 4.0 Principles of operation 4.8 Ope
- Page 21 and 22: 6.0 UPS monitoring 6.1 Overview A U
- Page 23 and 24: 7.0 Difficulty ENGLISH Caution !
- Page 25 and 26: 7.0 Schwierigkeit DEUTSCH Vorsicht
- Page 27 and 28: 7.0 Difficulty 7.1 Troubleshooting
- Page 29 and 30: 7.0 Difficulty 7.2 Replacing the ba
- Page 31 and 32: 8.0 Storing the UPS 8.1 Storage con
- Page 33 and 34: 10.0 Specifications 9.1 Input Nomin
- Page 35 and 36: Limited Warranty American Power Con
3.0 Installation<br />
3.7 Test for proper operation - continued<br />
cord. Observe that your equipment operates normally during both transfer from<br />
utility power to UPS power and back again. Repeat this test four or five times to<br />
ensure proper operation. See the following section covering Overloads if<br />
abnormal operation is encountered.<br />
The power I/0 control switches power to your equipment. If you leave your<br />
equipment power switches on, the I/0 power control can be used as a master on/<br />
off switch!<br />
3.8 Overloads<br />
If the total power requirement of your equipment is much greater than the<br />
capacity of the UPS, the UPS’s rear panel circuit breaker may trip. This is called<br />
an overload situation. Once the circuit breaker trips, the UPS will attempt to<br />
operate the load using its internal power source. This may result in an unexpectedly<br />
short run time or, if the overload is severe, the UPS will immediately shut<br />
down and cease to power the load. In this case, the UPS will emit a loud tone to<br />
alert you of the overload. If this occurs during your test, turn off the UPS and<br />
decide which equipment will be left unprotected by the UPS. The circuit breaker<br />
may be reset (press button) when the overload is removed.<br />
Page 12