- Page 3 and 4:
PROGRAMMERS REFERENCE MANUAL FOR UN
- Page 11 and 12:
TABLE OF CONTENTS (CONT.) Section T
- Page 14:
CHANGE 1 TABLE OF CONTENTS (CONT.)
- Page 17 and 18:
Section III III-A III-B TABLE OF CO
- Page 23 and 24:
TABLE OF CONTENTS (CONT.) Section T
- Page 25 and 26:
Table I-A-l 1-8-1 1-8-2 I-C-l I-C-2
- Page 27:
Figure II-F-l II-F-2 II-F-3 II-G-l
- Page 34:
8. Doors Open b. Doors Closed Figur
- Page 39 and 40:
ICR (P) An index control register (
- Page 41 and 42: Externally Specified Index (Dual Ch
- Page 44 and 45: Address 000066 000067 000070 000071
- Page 46: Address 00200 00201 00202 00203 002
- Page 53: TABLE I-B-1. REPERTOIRE OF INSTRUCT
- Page 58: 1. GENERAL SECTION I-B-2. ARITHMETI
- Page 61: 24 25 26 MULTIPLY AL (MULALB) (AL)
- Page 68 and 69: 02 03 06 COMPARE AL(CMAL) Execution
- Page 70: 50 63 53 COMPLEMENT A (CPA) Executi
- Page 74 and 75: 73 BJUMP (BJP) If B 1: 0, B-1---+B
- Page 76: 31 Instruction executed from entran
- Page 83: 1. GENERAL SECTION 1-8-7. SKIP AND
- Page 88 and 89: It should be noted that v in the in
- Page 90 and 91: 50 27 instruction will transfer a w
- Page 94 and 95: The second type is designed to tran
- Page 97 and 98: g) Peripheral equipment senses the
- Page 99: All steps of this sequence except t
- Page 103 and 104: Priority of output type functions (
- Page 105 and 106: different manner. The differences a
- Page 107: In dual channel mode the current bu
- Page 110: SECTION II. PERIPHERAL EQUIPMENT Th
- Page 121 and 122: 3.5 KEYBOARD INTERRUPT The computer
- Page 123: 1. GENERAL DESCRIPTION SECTION II-B
- Page 131 and 132: 1. BASIC INFORMATION SECTION II-C.
- Page 138 and 139: The read function performs the foll
- Page 140: 4.8 BACK SPACE (BITS 11-15) The bac
- Page 145:
(bioctal character) 7-bit frames, c
- Page 152:
If the status word indicates an out
- Page 156 and 157:
I -.-...----- - ---, Output Cable U
- Page 160:
5.1 IMPROPER CONDITION (BIT 14 = 1)
- Page 164:
command is sensed by the magnetic t
- Page 171:
Operation TABLE 11-0-3. OPERATION C
- Page 185 and 186:
TABLE II-F-l. 80-COLUMN CODE 80-Col
- Page 188:
storage. The last 18 characters are
- Page 199:
MSB Format A MSs
- Page 202 and 203:
CHANGE 2 Format A Format B 29 Forma
- Page 204 and 205:
CHANGE 2 Where: XX is not used S -
- Page 207 and 208:
Master Bit Position Where: 17 16 15
- Page 209:
2.6.2 INPUT DATA TRANSFER CHANGE 2
- Page 214 and 215:
CHANGE 2 Bit Designation 1 Status M
- Page 219:
3.7 ERROR NOTIFICATION CHANGE 2 The
- Page 222:
CHANGE 2 2) Press the PUNCH FEED tw
- Page 228:
CHANGE 2 Reason - A parity error ha
- Page 231 and 232:
Description - Empty Magazine or Ful
- Page 233:
Description - Control or Data Parit
- Page 236:
10 BASIC INFORMATION SECTION III-A.
- Page 242:
5. THE LOK TAG If the programmer wi
- Page 245:
These statements on a correction ta
- Page 251:
H H H I t:C I W Input WSI EXECurIVE
- Page 260:
204.3 MOVE OPERATION Input Operatio
- Page 270 and 271:
The available outputs are: No. 2 -
- Page 273 and 274:
c) Mount a source program tape in t
- Page 275:
1. INTRODUCTION SECTION III-C. TRIM
- Page 287:
2 •. 3.2 FORMAT B TRIM III also a
- Page 298:
2.5 DEBUGGING OPERATIONS TRIM III p
- Page 302:
3.2 80-COLUMN CARD INPUT FORMAT For
- Page 308:
CHANGE 1 3 0 5 GROUND RULES Regardl
- Page 314:
CHANGE 1 a) The computer stores the
- Page 319:
Entrance Address Base Address + 4 T
- Page 323 and 324:
2.4 INSPECT AND CHANGE The inspect
- Page 326 and 327:
The format of the UPAK I tape is su
- Page 328:
3.2.2 PAPER TAPE ABSOLUTE TYPEWRITE
- Page 334 and 335:
2.2 LOADING UPAK III To load the UP
- Page 338:
prepared tapes). An 88 indicates th
- Page 342 and 343:
5)' Start the computer. When the co
- Page 345:
Parameter 2 17 16 15 14 13 12 11 10
- Page 348 and 349:
4.4 . ALARMS AND STATUS INDICATIONS
- Page 353:
5) Start. the computer. 6) When the
- Page 360:
2) Instruction cards. Following the
- Page 376 and 377:
for every memory bank (409610 words
- Page 378 and 379:
1. GENERAL INFORMATION SECTION IV-D
- Page 380:
The format for card input is illust
- Page 386 and 387:
11) Start the computer. The listing
- Page 388 and 389:
1. GENERAL INFORMATION SECTION IV-E
- Page 394 and 395:
R - Resequence the selected job, wi
- Page 401:
3.9 CORRECTING JOBS The correct opt
- Page 404 and 405:
NOTE: If the punch is used for outp
- Page 406:
V. PROGRAMMER SERVICE SUBROUTINES P
- Page 422 and 423:
16. FLOATING POINT ARITHMETIC GENER
- Page 428:
Since the PCHC subroutine is called