- Page 3 and 4:
PROGRAMMERS REFERENCE MANUAL FOR UN
- Page 11 and 12:
TABLE OF CONTENTS (CONT.) Section T
- Page 14:
CHANGE 1 TABLE OF CONTENTS (CONT.)
- Page 17 and 18:
Section III III-A III-B TABLE OF CO
- Page 23 and 24:
TABLE OF CONTENTS (CONT.) Section T
- Page 25 and 26:
Table I-A-l 1-8-1 1-8-2 I-C-l I-C-2
- Page 27:
Figure II-F-l II-F-2 II-F-3 II-G-l
- Page 34:
8. Doors Open b. Doors Closed Figur
- Page 39 and 40:
ICR (P) An index control register (
- Page 41 and 42:
Externally Specified Index (Dual Ch
- Page 44 and 45:
Address 000066 000067 000070 000071
- Page 46:
Address 00200 00201 00202 00203 002
- Page 53:
TABLE I-B-1. REPERTOIRE OF INSTRUCT
- Page 58:
1. GENERAL SECTION I-B-2. ARITHMETI
- Page 61:
24 25 26 MULTIPLY AL (MULALB) (AL)
- Page 68 and 69:
02 03 06 COMPARE AL(CMAL) Execution
- Page 70:
50 63 53 COMPLEMENT A (CPA) Executi
- Page 74 and 75:
73 BJUMP (BJP) If B 1: 0, B-1---+B
- Page 76:
31 Instruction executed from entran
- Page 83:
1. GENERAL SECTION 1-8-7. SKIP AND
- Page 88 and 89:
It should be noted that v in the in
- Page 90 and 91:
50 27 instruction will transfer a w
- Page 92:
54 INDIRECT JUMP AND REMOVE INTERRU
- Page 95:
2. INPUT/OUTPUT INTERFACE 2.1 DATA
- Page 98 and 99:
c) Computer detects output request.
- Page 101:
The location (CAT) is specified by
- Page 104 and 105:
The following examp"le illustrates
- Page 106 and 107:
In the examples given above the wor
- Page 109 and 110:
equired only because the computer a
- Page 117:
3.3 PRINTER The printer prints data
- Page 122 and 123:
6) Output-data indicator switches T
- Page 126:
TABLE II-B-1. ASCII CODE FOR THE UN
- Page 132:
Tape Transport Control Tape Transpo
- Page 139 and 140:
computer program must then correct
- Page 142:
Bit 06 of the instruction word is u
- Page 147:
7.7 LONGITUDINAL PARITY ERROR (BITS
- Page 155 and 156:
magnetic tape control according to
- Page 157:
Order of Priority --+ Unit 1 Tape n
- Page 163 and 164:
5.10 LAST TAPE MOTION (BIT 05; 1 =
- Page 169:
TABLE 11-0-2. CHART SHOWING THE EFF
- Page 181:
TABLE II-0-4. TYPE SYMBOLS AND CODE
- Page 186:
- t I -- · - · -I · ,.. '" compu
- Page 192:
Command Type TABLE II-F-3. SUMMARY
- Page 201 and 202:
Format A Format B Format C 17 16 9
- Page 203 and 204:
Format A Format B Format C 3 5 34 2
- Page 205:
Serial Read/Punch - Contains one ha
- Page 208 and 209:
CHANGE 2 Code 3 4 5 I - Bits 3, 2.
- Page 211:
2.6.4 MAINTENANCE DATA TURNAROUND C
- Page 215:
Bit 2 3 4 5 6 7 Designation Bus Out
- Page 221 and 222:
4.2.1 POWER Turn on the system oper
- Page 225:
4.6.2 ABNORMAL CONDITIONS CHANGE 2
- Page 230 and 231:
CHANGE 2 Action - If a card has jam
- Page 232 and 233:
CHANGE 2 If another punch check err
- Page 235 and 236:
writer. These features cut TRIM III
- Page 240:
4. ·SPECIAL OPERATORS Each program
- Page 244 and 245:
One reject code - a single reject c
- Page 248:
c) Start the computer. 6) (AL) = 10
- Page 253:
2.1.2.2 OPERAND{S) One or a series
- Page 268: 2.5 DEBUGGING OPERATIONS TRIM II pr
- Page 271: 4) The maximum size program which T
- Page 274 and 275: If typeout suppression has been sel
- Page 280: TABLE III-C-l. TRIM III CODING SYMB
- Page 290: 2.4.3 MOVE OPERATION w MOVE • 1)
- Page 300: The DTYPT operation performs the sa
- Page 305: 3.3 MAGNETIC TAPE INPUT FORMAT CHAN
- Page 312: CHANGE 1 b) If no additional input
- Page 321: The load subroutine stores the init
- Page 324: SEARCH 1219 LLLLL TO UUUUU MM MMMM
- Page 327 and 328: typed on the on-line typewriter. Th
- Page 331: 6) Start the computer. The computer
- Page 335: If the parameter does not specify t
- Page 341 and 342: 3) Start the computer. The computer
- Page 343: 3.2.0 PROGRAM OPERATION OF DUMP BIO
- Page 347 and 348: 4.3 OPERATING PROCEDURES 4.3.1 CPER
- Page 349: 3) That-address 00141 is reserved f
- Page 356: 6.4 . ALARMS AND STATUS INDICATIONS
- Page 362: 9.2 INPUT PARAMETERS CHANGE 1 The c
- Page 377 and 378:
8) Release PROGRAM SKIP key 1. 9) M
- Page 379 and 380:
RPL (replace - program with new pro
- Page 385 and 386:
CHANGE 1 if- input is from tape, it
- Page 387 and 388:
10) Tes ERR Z TBL Y. The table cont
- Page 389:
3. OUTPUT The output of the TRACK p
- Page 395:
The codes required are as follows:
- Page 403 and 404:
CHANGE 1 4. OPERATING PROCEDURES Th
- Page 405 and 406:
CHANGE 1 4) ILLEGAL OPERATOR. The o
- Page 420:
If the argument falls within the ra
- Page 423:
SECTION V-B. CONVERSION SUBROUTINES
- Page 431:
00 01 02 03 0 04 Space 05 ( 06 0 07