- Page 3 and 4:
PROGRAMMERS REFERENCE MANUAL FOR UN
- Page 11 and 12:
TABLE OF CONTENTS (CONT.) Section T
- Page 14:
CHANGE 1 TABLE OF CONTENTS (CONT.)
- Page 17 and 18:
Section III III-A III-B TABLE OF CO
- Page 23 and 24:
TABLE OF CONTENTS (CONT.) Section T
- Page 25 and 26:
Table I-A-l 1-8-1 1-8-2 I-C-l I-C-2
- Page 27:
Figure II-F-l II-F-2 II-F-3 II-G-l
- Page 34:
8. Doors Open b. Doors Closed Figur
- Page 39 and 40:
ICR (P) An index control register (
- Page 41 and 42:
Externally Specified Index (Dual Ch
- Page 44 and 45:
Address 000066 000067 000070 000071
- Page 46:
Address 00200 00201 00202 00203 002
- Page 53:
TABLE I-B-1. REPERTOIRE OF INSTRUCT
- Page 58:
1. GENERAL SECTION I-B-2. ARITHMETI
- Page 61:
24 25 26 MULTIPLY AL (MULALB) (AL)
- Page 68 and 69:
02 03 06 COMPARE AL(CMAL) Execution
- Page 70:
50 63 53 COMPLEMENT A (CPA) Executi
- Page 74 and 75:
73 BJUMP (BJP) If B 1: 0, B-1---+B
- Page 76:
31 Instruction executed from entran
- Page 83:
1. GENERAL SECTION 1-8-7. SKIP AND
- Page 88 and 89:
It should be noted that v in the in
- Page 90 and 91:
50 27 instruction will transfer a w
- Page 92:
54 INDIRECT JUMP AND REMOVE INTERRU
- Page 95:
2. INPUT/OUTPUT INTERFACE 2.1 DATA
- Page 98 and 99:
c) Computer detects output request.
- Page 101:
The location (CAT) is specified by
- Page 104 and 105:
The following examp"le illustrates
- Page 106 and 107:
In the examples given above the wor
- Page 109 and 110:
equired only because the computer a
- Page 117:
3.3 PRINTER The printer prints data
- Page 122 and 123:
6) Output-data indicator switches T
- Page 126:
TABLE II-B-1. ASCII CODE FOR THE UN
- Page 132:
Tape Transport Control Tape Transpo
- Page 139 and 140:
computer program must then correct
- Page 142:
Bit 06 of the instruction word is u
- Page 147:
7.7 LONGITUDINAL PARITY ERROR (BITS
- Page 155 and 156:
magnetic tape control according to
- Page 157:
Order of Priority --+ Unit 1 Tape n
- Page 163 and 164:
5.10 LAST TAPE MOTION (BIT 05; 1 =
- Page 169:
TABLE 11-0-2. CHART SHOWING THE EFF
- Page 181:
TABLE II-0-4. TYPE SYMBOLS AND CODE
- Page 186: - t I -- · - · -I · ,.. '" compu
- Page 192: Command Type TABLE II-F-3. SUMMARY
- Page 201 and 202: Format A Format B Format C 17 16 9
- Page 203 and 204: Format A Format B Format C 3 5 34 2
- Page 205: Serial Read/Punch - Contains one ha
- Page 208 and 209: CHANGE 2 Code 3 4 5 I - Bits 3, 2.
- Page 211: 2.6.4 MAINTENANCE DATA TURNAROUND C
- Page 215: Bit 2 3 4 5 6 7 Designation Bus Out
- Page 221 and 222: 4.2.1 POWER Turn on the system oper
- Page 225: 4.6.2 ABNORMAL CONDITIONS CHANGE 2
- Page 230 and 231: CHANGE 2 Action - If a card has jam
- Page 232 and 233: CHANGE 2 If another punch check err
- Page 236: 10 BASIC INFORMATION SECTION III-A.
- Page 242: 5. THE LOK TAG If the programmer wi
- Page 245: These statements on a correction ta
- Page 251: H H H I t:C I W Input WSI EXECurIVE
- Page 260: 204.3 MOVE OPERATION Input Operatio
- Page 270 and 271: The available outputs are: No. 2 -
- Page 273 and 274: c) Mount a source program tape in t
- Page 275: 1. INTRODUCTION SECTION III-C. TRIM
- Page 287:
2 •. 3.2 FORMAT B TRIM III also a
- Page 298:
2.5 DEBUGGING OPERATIONS TRIM III p
- Page 302:
3.2 80-COLUMN CARD INPUT FORMAT For
- Page 308:
CHANGE 1 3 0 5 GROUND RULES Regardl
- Page 314:
CHANGE 1 a) The computer stores the
- Page 319:
Entrance Address Base Address + 4 T
- Page 323 and 324:
2.4 INSPECT AND CHANGE The inspect
- Page 326 and 327:
The format of the UPAK I tape is su
- Page 328:
3.2.2 PAPER TAPE ABSOLUTE TYPEWRITE
- Page 334 and 335:
2.2 LOADING UPAK III To load the UP
- Page 338:
prepared tapes). An 88 indicates th
- Page 342 and 343:
5)' Start the computer. When the co
- Page 345:
Parameter 2 17 16 15 14 13 12 11 10
- Page 348 and 349:
4.4 . ALARMS AND STATUS INDICATIONS
- Page 353:
5) Start. the computer. 6) When the
- Page 360:
2) Instruction cards. Following the
- Page 376 and 377:
for every memory bank (409610 words
- Page 378 and 379:
1. GENERAL INFORMATION SECTION IV-D
- Page 380:
The format for card input is illust
- Page 386 and 387:
11) Start the computer. The listing
- Page 388 and 389:
1. GENERAL INFORMATION SECTION IV-E
- Page 394 and 395:
R - Resequence the selected job, wi
- Page 401:
3.9 CORRECTING JOBS The correct opt
- Page 404 and 405:
NOTE: If the punch is used for outp
- Page 406:
V. PROGRAMMER SERVICE SUBROUTINES P
- Page 422 and 423:
16. FLOATING POINT ARITHMETIC GENER
- Page 428:
Since the PCHC subroutine is called