Precious Metals Recovery LLC RCRA Permit Application Dry Hills ...

More documents

Recommendations

Info

grouped together. Containers in each of these groups will be sampled as described below (Table 4 found in Section 12). The samples within each separate group may be composited for analysis. A unique tracking number will be assigned to each container. Samples will be taken from locations displaced vertically throughout the waste. For liquids (or liquids with precipitated solids), the operator performing the sampling will use a COLIWASA or equivalent. The sampling device will be inserted into the container from the top and is pushed down slowly until the bottom of the container is reached. The device will be sealed to retain the contents. The contents of the sampling device will then transferred to a polyethylene or glass bottle, which will be labeled with waste identification information. The sampling device may also be stoppered at both ends, wiped dry with a disposable cloth, and then transferred to the lab for analysis. A trier or thief will be used to sample containers that are solid in nature. These containers are generally filled with dirt and sludges. Several areas from the container will be sampled and composited into a jar in order to ensure a representative sample. The operator performing the sampling will remove a sample that uniformly represents the waste composition of the container (i.e., all layers and phases will be represented in the sample). Sampling of Tanks A representative sample will be collected on either the side or bottom of each tank. Frozen Waste The proposed TSF will not sample waste that is frozen. The truck will park in the truck unloading area until the waste can be sampled. A sample will then be collected as outlined in this section. Sampling of Treatment Residue Samples of incoming waste, treatment residue, filter cake, and hygiene dust collector dust will be collected to determine if LDR treatment standards are met. For retort residues, grab samples may be taken at the end of processing batch. Sampling events will be recorded in the operating record. For hygiene dust collector dust, a sample will be taken in preparation for off-site disposal. Waste Analysis Plan App 2A-Page 10 JBR Environmental Consultants, Inc. March 2013
9 LDR TREATMENT STANDARDS Waste Description (D009 Mercury) Management LDR Requirement (Non-wastewater) Elemental Mercury Storage N/A (not disposed) N/A Calomel Treatment High mercury inorganic subcategory (D009 with total mercury greater than 260 mg/kg) Spent Activated Carbon Filter Cake Pretreated and then retorted Retort High mercury inorganic subcategory (D009 with total mercury greater than 260 mg/kg) High mercury inorganic subcategory (D009 with total mercury greater than 260 mg/kg) Treatment Standard UHC applies to the treatment residues. Retorting (RMERC) UHC may apply to the treatment residues. Retorting (RMERC) UHC applies to treatment residues. Waste Analysis Plan App 2A-Page 11 JBR Environmental Consultants, Inc. March 2013
Page 1 and 2:
Precious Metals Recovery LLC RCRA P
Page 3 and 4:
ITEM # REGULATIONS GENERAL DESCRIPT
Page 5 and 6:
Page 7 and 8:
PMR Nevada RCRA Permit Application
Page 9 and 10:
PMR Nevada RCRA Permit Application
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
M-3 M-3 ITEM # REGULATIONS GENERAL
Page 21 and 22:
OMB# 2050-0024; Expires ___________
Page 23 and 24:
EPA ID Number OMB#: 2050-0024; Expi
Page 25 and 26:
EPA ID Number ADDENDUM TO THE SITE
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
This document is for reference purp
Page 35 and 36:
A B C D E F $$W ATERMARKD$$ N 4,475
Page 37 and 38:
Precious Metals Recovery LLC Dry Hi
Page 39 and 40:
3.2 Barrier and Means to Control En
Page 41 and 42:
19.0 APPROVAL OF PETITION FOR EXTEN
Page 43 and 44:
LIST OF TABLES Table 1.2-1 Secondar
Page 45 and 46:
Figure 23.1-1 Decomposition & Waste
Page 47 and 48:
Section 10 Appendices 10-A Figures
Page 49 and 50:
HVAC Heating, Ventilation, and Air
Page 51 and 52:
GLOSSARY OF SELECTED TERMS [Authori
Page 53 and 54:
INTRODUCTION Precious Metals Recove
Page 55 and 56:
Pre-application Public Meeting - 40
Page 57 and 58:
(Purity ≥ 99.5%, Directly Stored)
Page 59 and 60:
Administration (MSHA) document, Con
Page 61 and 62:
Fire Doors/Emergency Exit Doors Pr
Page 63 and 64:
When leaving the plant spaces, work
Page 65 and 66:
Infiltration Air Office Area Pig Pi
Page 67 and 68:
personnel will be trained in respon
Page 69 and 70:
Figure 1.2-1: Elemental Mercury Tra
Page 71 and 72:
Tanks Or Containers Carbon Drums (n
Page 73 and 74:
Figure 1.2-2: Calomel Feed Preparat
Page 75 and 76:
Figure 1.2-3: Filter Press and Loca
Page 77 and 78:
Activated carbon is used in the air
Page 79 and 80:
Figure 1.2-5: SO2 Scrubber and Loca
Page 81 and 82:
Above the retort tray/drum transfer
Page 83 and 84:
Figure 1.2-8: Carbon Filter and Loc
Page 85 and 86:
Figure 1.2-10: Overall Ventilation
Page 87 and 88:
Wash water from open sumps. Safety
Page 89 and 90:
1.3 Elemental Mercury Storage - 40
Page 91 and 92:
The following items are located out
Page 93 and 94:
Control System Architecture The pla
Page 95 and 96:
will be supplied in accordance with
Page 97 and 98:
Outdoor Material Storage A list of
Page 99 and 100:
It is recognized that the fire prot
Page 101 and 102:
Outdoor Areas Hydrants and hose bo
Page 103 and 104:
the event of a security violation,
Page 105 and 106:
2.3 Determination of Treatment Para
Page 107 and 108:
Table 2.5-2: Test Methods Parameter
Page 109 and 110:
Sampling Containerized Waste The te
Page 111 and 112:
Process Waste Solution A discrete p
Page 113 and 114:
ii. The sampling person removes a s
Page 115 and 116:
2.9 Screening for Ignitable, Reacti
Page 117 and 118:
3.0 SECURITY PLAN - 40 CFR 270.14(b
Page 119 and 120:
4.0 INSPECTION PLAN - 40 CFR 270.14
Page 121 and 122:
TSF, associated hazards, places whe
Page 123 and 124:
Outside of working hours, a notific
Page 125 and 126:
Damaged containers will be placed i
Page 127 and 128:
7.0 PREVENTION AND SAFETY PROCEDURE
Page 129 and 130:
8.0 PREVENTION OF ACCIDENTAL IGNITI
Page 131 and 132:
10.0 TRAFFIC - 40 CFR 270.14(b)(10)
Page 133 and 134:
Delivery frequency of reagents will
Page 135 and 136:
10.3 Traffic Control Signs Traffic
Page 137 and 138:
11.4 Surrounding Land Use - 40 CFR
Page 139 and 140:
12.0 PERSONNEL TRAINING PLAN - 40 C
Page 141 and 142:
that are not land based. Closure of
Page 143 and 144:
13.4.6 Types of Off-site Waste Mana
Page 145 and 146:
14.0 CLOSED HAZARDOUS WASTE DISPOSA
Page 147 and 148:
storage area (e.g., storage racks),
Page 149 and 150:
16.0 POST-CLOSURE ESTIMATES - 40 CF
Page 151 and 152:
18.0 TOPOGRAPHICAL MAP - 40 CFR 270
Page 153 and 154:
20.0 GROUNDWATER MONITORING - 40 CF
Page 155 and 156:
22.0 CONTAINERS AND CONTAINMENT - 4
Page 157 and 158:
Figure 22.1-2: Dedicated Transfer C
Page 159 and 160:
Larger sized HDPE drums may be used
Page 161 and 162:
22.3.2 Labeling Containers - 40 CFR
Page 163 and 164:
22.5 Description of Secondary Conta
Page 165 and 166:
will be done on the new waste strea
Page 167 and 168:
23.0 TREATMENT AND STORAGE TANKS Me
Page 169 and 170:
Figure 23.0-2: HCl Tank and Locatio
Page 171 and 172:
Tank Dimensions Waste Solution Stor
Page 173 and 174:
decomposed in the Decomposition Tan
Page 175 and 176:
Figure 23.1-3: Waste Solution Stora
Page 177 and 178:
The Water Storage Tank will supply
Page 179 and 180:
Tank Caustic Soda Storage Tank* Hyd
Page 181 and 182:
23.13 Recordkeeping A recordkeeping
Page 183 and 184:
25.0 WASTE PILES - 40 CFR 270.18 &
Page 185 and 186:
27.0 LAND TREATMENT - 40 CFR 270.20
Page 187 and 188:
29.0 BOILERS/INDUSTRIAL FURNACE - 4
Page 189 and 190:
30.1.3 Retort Operating Procedures
Page 191 and 192:
of 13.5 feet long by 4.7 feet wide
Page 193 and 194:
31.0 PROCESS VENTS - 40 CFR 270.24
Page 195 and 196:
33.0 DRIP PADS - 40 CFR 270.26 & 26
Page 197 and 198:
35.0 REFERENCES American Society of
Page 199 and 200:
At the PMR Dry Hills Facility Open
Page 217 and 218:
APPENDIX I-B Open House Comments
Page 219 and 220:
APPENDIX 1-A Drawings Facility draw
Page 221 and 222:
A B C D EF $ $ W A TERMARKA1$$ H340
Page 223 and 224:
A B C D E F $$W ATERMARKD$$ 1 2 3 4
Page 225 and 226:
A B C D E F $$W ATERMARKD$$ N 4,475
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
A B C D EF $ $ W A TERMARKA1$$ H340
Page 237 and 238:
A B C D E F $$W ATERMARKD$$ H340940
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
A B C D E F $$W ATERMARKD$$ NOTE: 1
Page 251 and 252:
Page 253 and 254: B A B C D E F $$W ATERMARKD$$ H3409
Page 255 and 256: A B C D E F $$W ATERMARKD$$ H340940
Page 259 and 260: APPENDIX 1-C Process Flow Diagrams
Page 261 and 262: A B C D E F $$W ATERMARKD$$ 1 2 3 4
Page 273 and 274: H - 340940 Precious Metals Recovery
Page 283 and 284: APPENDIX 1-D Floor and Wall Sealant
Page 285 and 286: C8 x 11.5 EPOXY COATING ON 2" THICK
Page 287 and 288: 8" THICK INSULATED PRECAST CONCRETE
Page 289 and 290: C8 x 11.5 EPOXY COATING ON 2" THICK
Page 291 and 292: 2. PRODUCTS 2.1 Stonclad GS Stoncla
Page 293 and 294: APPENDIX 2-A Waste Analysis Plan
Page 295 and 296: WASTE ANALYSIS PLAN 1 PURPOSE AND S
Page 297 and 298: Table 1: Analytical Methods for the
Page 299 and 300: All wastes received will have been
Page 301 and 302: Waste will not be accepted until th
Page 303: Table 3: Waste Sampling Matrix Type
Page 307 and 308: Drummed consolidation waste will be
Page 309 and 310: eevaluated whenever the process tha
Page 311 and 312: ATTACHMENT 2-A-1 Profile Instructio
Page 313 and 314: PMR LLC 460 W. 50 North Suite 500 S
Page 315 and 316: • Is the waste pyrophoric? a See
Page 317 and 318: EPA's Chemical Compatibility Chart
Page 319 and 320: 1.0 SCOPE AND APPLICATION METHOD 90
Page 321 and 322: 7.2.3 Adjust the electrodes in the
Page 323 and 324: METHOD 9045D SOIL AND WASTE pH 9045
Page 325 and 326: NOTE: Combination electrodes incorp
Page 327 and 328: 10.0 REFERENCES 1. National Bureau
Page 329 and 330: 1.0 SCOPE AND APPLICATION METHOD 13
Page 331 and 332: 4.2.2 Bottle Extraction Vessel. Whe
Page 333 and 334: 4.10 Watchglass, appropriate diamet
Page 335 and 336: 7.0 PROCEDURE 7.1 Preliminary Evalu
Page 337 and 338: determine whether the solid materia
Page 339 and 340: solids content of the waste sample
Page 341 and 342: material into an extractor bottle.
Page 343 and 344: sample from which no additional liq
Page 345 and 346: slowly out of the ZHE device into a
Page 347 and 348: ® TEDLAR bag is used, if the extra
Page 349 and 350: 150% of the expected concentration
Page 351 and 352: None of the parameters had a signif
Page 353 and 354: Table 2. Suitable Rotary Agitation
Page 355 and 356:
Table 4. Suitable Filter Holders 1
Page 357 and 358:
Table 6. Multi-Laboratory TCLP Meta
Page 359 and 360:
Table 8. Multi-Laboratory Semi-Vola
Page 361 and 362:
Figure 1. Rotary Agitation Apparatu
Page 363 and 364:
METHOD 1311 (CONTINUED) TOXICITY CH
Page 365 and 366:
Designation: D4979 − 08 Standard
Page 367 and 368:
Designation: D4978 − 95 (Reapprov
Page 369 and 370:
FIG. 1 Method B, Sulfide Test Appar
Page 371 and 372:
TABLE 1 Determination of Bias, Pycn
Page 373 and 374:
for four known specific gravity lev
Page 375 and 376:
21.7.1 To check the precision of sa
Page 377 and 378:
Page 379 and 380:
Page 381 and 382:
11.6.1 Compare the temperature here
Page 383 and 384:
APPENDIX 2-E Characterization Data
Page 385 and 386:
5. Fire-fighting measures General I
Page 387 and 388:
Carcinogenicity: CAS# 10112‐91‐
Page 393 and 394:
Combined Hazen Solution Analysis pH
Page 395 and 396:
irritation and possible burns. May
Page 397 and 398:
OSHA Vacated PELs: Mercury: 0.05 mg
Page 399 and 400:
Chemical waste generators must dete
Page 401 and 402:
APPENDIX 4-A Inspection Plan
Page 403 and 404:
1 INSPECTION PLAN This Inspection P
Page 405 and 406:
Inspections are intended to detect
Page 407 and 408:
Boilers and Industrial Furnaces Ins
Page 409 and 410:
PMR Daily Inspection Form #1 Date:
Page 411 and 412:
PMR Daily Inspection Form #2 Date:
Page 413 and 414:
PMR Weekly Inspection Form #3 Date:
Page 415 and 416:
damage or vandalism. Other Inspecti
Page 417 and 418:
TABLE OF CONTENTS 1 CONTINGENCY PLA
Page 419 and 420:
Potential Emergency Condition Fire,
Page 421 and 422:
Other duties of the emergency coord
Page 423 and 424:
Determine proper storage and placem
Page 425 and 426:
Neoprene boots - protect feet. Res
Page 427 and 428:
Fire Extinguishers. Absorbent pads
Page 429 and 430:
Table 2: Coordinating Agency Contac
Page 431 and 432:
Stay low in smoke filled areas. Co
Page 433 and 434:
the area or the National Response C
Page 435 and 436:
Description of the spilled material
Page 437 and 438:
APPENDIX 6-B Emergency Coordinators
Page 439:
Ambulance EXTERNAL CONTACTS Name Ti
show all

Precious Metals Recovery LLC RCRA Permit Application Dry Hills ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?