Precious Metals Recovery LLC RCRA Permit Application Dry Hills ...
Precious Metals Recovery LLC RCRA Permit Application Dry Hills ... Precious Metals Recovery LLC RCRA Permit Application Dry Hills ...
7 SHIPMENT EVALUATION Materials shall arrive by truck at the proposed TSF. Containers or pallets in the transportation vehicle will be monitored for mercury vapor and visually inspected for integrity, leaks and spills. After the initial inspection and manifest confirmation, a forklift shall transport the pallets from the truck to the receiving and inspection area, where the containers and pallets will undergo a more thorough inspection for leaks, cracks, dents, beading, corrosion, and seal integrity. Mercury vapor levels will be monitored, and containers will be inspected and sampled in the ventilated receiving and inspection area. Material arriving at the proposed TSF will be fingerprinted before storage and processing. Fingerprinting will consist of visual inspection, sampling, and testing of the material. Testing of samples will be performed in the on-site lab. 8 SAMPLING The appropriate representative sampling techniques, devices, and containers are selected from the EPA document, Test Methods for Evaluating Solid Wastes (SW-846) or American Society for Testing and Materials (ASTM) methods. Specific sampling methods (Table 3) and analytical methods (Table 1) are specified. Waste sampled at the proposed TSF will consist of new waste, unknown waste, waste from changed processes, and waste sampled for annual re-verification analysis. Representative samples will be collected and handled in accordance with the procedures and protocols identified in Table 3. At a minimum, the following safety precautions are used when sampling waste materials: Chemical resistant gloves and safety glasses will be used while sampling all waste. Based on the chemical hazards and splash potential, protective clothing and a splash shield or respirator may also be utilized. All necessary equipment and materials will be readily available and staged prior to sampling. Waste Analysis Plan App 2A-Page 8 JBR Environmental Consultants, Inc. March 2013
Table 3: Waste Sampling Matrix Type of Waste Sampling Device Free Flowing Liquids/Slurries Sampling Port, Pump/Dipper Sludges COLIWASA Moist Powder/Granules Trier/Spoon Dry Powder/Granules Trier/Spoon Large Grained Solids Thief/Spoon Debris (i.e. Rags, Gloves, Towels, etc.) Large Trier/Spoon, Rag The rag technique will be used for sampling solid material such as rags, gloves and paper towels. After a container has been selected, it will be opened and a representative sample collected and placed in the sample container. One or more of the varied materials (e.g. gloves, rags, paper, plastic, etc.) will be sampled depending on the mix of the container. A variety of sampling equipment and materials will be used to collect waste samples. Types of equipment and specified sampling methods are described in the SW-846 publication. Sampling of Containers Container shipments will be sampled and the sample composites will be analyzed for the acceptance parameters listed in Table 2. If the wastes can be managed and are not prohibited at the proposed TSF, the containers can then be accepted. All of the analyses needed for the acceptance and storage functions are performed during incoming load verification. Treatment of the waste changes its characteristics and requires additional sampling, inspection, and analysis to determine the appropriate disposal of the waste. A random sampling strategy will be employed to sample incoming shipments of containerized waste. Samples from containers holding the same type of waste may be composited. The following procedure will be used to determine how many containers will be sampled and which samples will be composited. Each container will be opened and visually inspected. Wastes on a single load that have the same profile number and DOT description (excluding waste codes), and appear to be of the same waste type will be Waste Analysis Plan App 2A-Page 9 JBR Environmental Consultants, Inc. March 2013
- Page 251 and 252: A B C D E F $$W ATERMARKD$$ H340940
- Page 253 and 254: B A B C D E F $$W ATERMARKD$$ H3409
- Page 255 and 256: A B C D E F $$W ATERMARKD$$ H340940
- Page 257 and 258: A B C D E F $$W ATERMARKD$$ H340940
- Page 259 and 260: APPENDIX 1-C Process Flow Diagrams
- Page 261 and 262: A B C D E F $$W ATERMARKD$$ 1 2 3 4
- Page 263 and 264: A B C D E F $$W ATERMARKD$$ H340940
- Page 265 and 266: A B C D E F $$W ATERMARKD$$ H340940
- Page 267 and 268: A B C D E F $$W ATERMARKD$$ H340940
- Page 269 and 270: A B C D E F $$W ATERMARKD$$ H340940
- Page 271 and 272: A B C D E F $$W ATERMARKD$$ H340940
- Page 273 and 274: H - 340940 Precious Metals Recovery
- Page 275 and 276: H - 340940 Precious Metals Recovery
- Page 277 and 278: H - 340940 Precious Metals Recovery
- Page 279 and 280: H - 340940 Precious Metals Recovery
- Page 281 and 282: H - 340940 Precious Metals Recovery
- Page 283 and 284: APPENDIX 1-D Floor and Wall Sealant
- Page 285 and 286: C8 x 11.5 EPOXY COATING ON 2" THICK
- Page 287 and 288: 8" THICK INSULATED PRECAST CONCRETE
- Page 289 and 290: C8 x 11.5 EPOXY COATING ON 2" THICK
- Page 291 and 292: 2. PRODUCTS 2.1 Stonclad GS Stoncla
- Page 293 and 294: APPENDIX 2-A Waste Analysis Plan
- Page 295 and 296: WASTE ANALYSIS PLAN 1 PURPOSE AND S
- Page 297 and 298: Table 1: Analytical Methods for the
- Page 299 and 300: All wastes received will have been
- Page 301: Waste will not be accepted until th
- Page 305 and 306: 9 LDR TREATMENT STANDARDS Waste Des
- Page 307 and 308: Drummed consolidation waste will be
- Page 309 and 310: eevaluated whenever the process tha
- Page 311 and 312: ATTACHMENT 2-A-1 Profile Instructio
- Page 313 and 314: PMR LLC 460 W. 50 North Suite 500 S
- Page 315 and 316: • Is the waste pyrophoric? a See
- Page 317 and 318: EPA's Chemical Compatibility Chart
- Page 319 and 320: 1.0 SCOPE AND APPLICATION METHOD 90
- Page 321 and 322: 7.2.3 Adjust the electrodes in the
- Page 323 and 324: METHOD 9045D SOIL AND WASTE pH 9045
- Page 325 and 326: NOTE: Combination electrodes incorp
- Page 327 and 328: 10.0 REFERENCES 1. National Bureau
- Page 329 and 330: 1.0 SCOPE AND APPLICATION METHOD 13
- Page 331 and 332: 4.2.2 Bottle Extraction Vessel. Whe
- Page 333 and 334: 4.10 Watchglass, appropriate diamet
- Page 335 and 336: 7.0 PROCEDURE 7.1 Preliminary Evalu
- Page 337 and 338: determine whether the solid materia
- Page 339 and 340: solids content of the waste sample
- Page 341 and 342: material into an extractor bottle.
- Page 343 and 344: sample from which no additional liq
- Page 345 and 346: slowly out of the ZHE device into a
- Page 347 and 348: ® TEDLAR bag is used, if the extra
- Page 349 and 350: 150% of the expected concentration
- Page 351 and 352: None of the parameters had a signif
Table 3: Waste Sampling Matrix<br />
Type of Waste Sampling Device<br />
Free Flowing Liquids/Slurries Sampling Port, Pump/Dipper<br />
Sludges COLIWASA<br />
Moist Powder/Granules Trier/Spoon<br />
<strong>Dry</strong> Powder/Granules Trier/Spoon<br />
Large Grained Solids Thief/Spoon<br />
Debris (i.e. Rags, Gloves,<br />
Towels, etc.) Large Trier/Spoon, Rag<br />
The rag technique will be used for sampling solid material such as rags, gloves and paper towels.<br />
After a container has been selected, it will be opened and a representative sample collected and<br />
placed in the sample container. One or more of the varied materials (e.g. gloves, rags, paper,<br />
plastic, etc.) will be sampled depending on the mix of the container.<br />
A variety of sampling equipment and materials will be used to collect waste samples. Types of<br />
equipment and specified sampling methods are described in the SW-846 publication.<br />
Sampling of Containers<br />
Container shipments will be sampled and the sample composites will be analyzed for the<br />
acceptance parameters listed in Table 2. If the wastes can be managed and are not prohibited<br />
at the proposed TSF, the containers can then be accepted.<br />
All of the analyses needed for the acceptance and storage functions are performed during<br />
incoming load verification. Treatment of the waste changes its characteristics and requires<br />
additional sampling, inspection, and analysis to determine the appropriate disposal of the<br />
waste.<br />
A random sampling strategy will be employed to sample incoming shipments of<br />
containerized waste. Samples from containers holding the same type of waste may be<br />
composited. The following procedure will be used to determine how many containers will<br />
be sampled and which samples will be composited. Each container will be opened and<br />
visually inspected. Wastes on a single load that have the same profile number and DOT<br />
description (excluding waste codes), and appear to be of the same waste type will be<br />
Waste Analysis Plan App 2A-Page 9<br />
JBR Environmental Consultants, Inc. March 2013