TDP-459 Users Guide - MItsubishi Imaging
TDP-459 Users Guide - MItsubishi Imaging TDP-459 Users Guide - MItsubishi Imaging
3.3.4 Checking the firmware versions 1. In the ready state, press the menu button once, press the + button 3 times, and display “Firmware Version” on the LCD. - 31 - Chapter 3 Use of Operation Panel [Useful tip] Pressing the + or - button repeatedly changes the message on the LCD as shown below. 2. Press the enter button to select the operation for checking firmware versions. 3. Press the + or - button to display another firmware version. 4. Press the clear button repeatedly until the ready state is displayed. Firmware Version MAIN Ver. **.** TABLE Ver. **.** TDP-459
Chapter 3 Use of Operation Panel 3.3.5 Setting the Head Cleaning Mode and Execution in Head Cleaning Setup of the automatic cleaning mode (ON/OFF) The automatic cleaning mode (ON/OFF) is set as follows. When it is set at ON, the automatic head cleaning is executed every time before printing. This mode is effective for only when extra mode* is selected. When standard mode* is selected, the automatic head cleaning is not executed, regardless of setting the head cleaning mode (ON/OFF) * Refer to the supplied instruction manual for Windows printer driver in the CD in this machine. 1. In the ready state, press the menu button once, press the + button 4 times, and display ”Head Cleaning” on the LCD. Head Cleaning TDP-459 [Useful tip] Pressing the + or - button repeatedly changes the message on the LCD as shown below. 2. Press the enter button to select the operation for setting the Cleaning mode. 3. Press the enter button, and display the setting state (on/off) of head cleaning mode. 4. Press the + or - button to change the setting (on/off) of head cleaning mode. - 32 - Cleaning Sw Cleaning Swoff Cleaning Swon
- Page 2: Introduction Thank you for purchasi
- Page 5 and 6: Table of Contents Chapter 5 Trouble
- Page 7 and 8: Chapter 1 Safety Precautions 1.1 Ca
- Page 9 and 10: Chapter 1 Safety Precautions Use on
- Page 11 and 12: Chapter 1 Safety Precautions 1.4 Ha
- Page 13 and 14: Chapter 2 Installation and Setup Ch
- Page 15 and 16: Chapter 2 Installation and Setup 2.
- Page 17 and 18: Chapter 2 Installation and Setup I
- Page 19 and 20: Chapter 2 Installation and Setup 2.
- Page 21 and 22: Chapter 2 Installation and Setup 2.
- Page 23 and 24: Chapter 2 Installation and Setup 5.
- Page 25 and 26: Chapter 2 Installation and Setup 11
- Page 27 and 28: Chapter 2 Installation and Setup 2.
- Page 29 and 30: Chapter 3 Use of Operation Panel TD
- Page 31 and 32: Chapter 3 Use of Operation Panel 3.
- Page 33 and 34: Chapter 3 Use of Operation Panel 3.
- Page 35: Chapter 3 Use of Operation Panel 3.
- Page 39 and 40: Chapter 3 Use of Operation Panel 5.
- Page 41 and 42: Chapter 3 Use of Operation Panel 3.
- Page 43 and 44: Chapter 4 Daily Maintenance Chapter
- Page 45 and 46: Chapter 4 Daily Maintenance < Clean
- Page 47 and 48: Chapter 4 Daily Maintenance 4.2 Cle
- Page 49 and 50: Chapter 5 Troubleshooting Chapter 5
- Page 51 and 52: Chapter 5 Troubleshooting When the
- Page 53 and 54: Chapter 5 Troubleshooting 5.3 When
- Page 55 and 56: Chapter 5 Troubleshooting 3. Wipe t
- Page 57 and 58: Chapter 6 After-sales service Chapt
- Page 59 and 60: Chapter 7 Specification Chapter 7 S
3.3.4 Checking the firmware versions<br />
1. In the ready state, press the menu button<br />
once, press the + button 3 times, and<br />
display “Firmware Version” on the LCD.<br />
- 31 -<br />
Chapter 3 Use of Operation Panel<br />
[Useful tip]<br />
Pressing the + or - button repeatedly changes the message on the LCD as<br />
shown below.<br />
2. Press the enter button to select the<br />
operation for checking firmware versions.<br />
3. Press the + or - button to display another<br />
firmware version.<br />
4. Press the clear button repeatedly until the<br />
ready state is displayed.<br />
Firmware Version<br />
MAIN Ver. **.**<br />
TABLE Ver. **.**<br />
<strong>TDP</strong>-<strong>459</strong>