TDP-459 Users Guide - MItsubishi Imaging
TDP-459 Users Guide - MItsubishi Imaging TDP-459 Users Guide - MItsubishi Imaging
8. Install and fit the flange (anti-gear side) to the end of the shaft on the opposite side of stopper the plate. Flange (anti-gear side) - 19 - Chapter 2 Installation and Setup [Useful tip] The flange (anti-gear side) has a stopper notch and the shaft has stopper notches to prevent empty rotation. Check the directions of the spool stopper notch and notches on the shaft to fit the spool correctly. 9. Tighten the screw to fix, forcing the flange (anti-gear side) on the side of the plate, and fix the flange (anti-gear side). 10. Install the plate by placing the spool into the plate box. The plate weighs approx. 10 kg (22 lbs). Handle it carefully so as not to drop it. Dropping it is dangerous. Screw to fix TDP-459
Chapter 2 Installation and Setup 11. Remove the seal fixing the end of the plate. Fixing seal 12. Feed in the plate by hand, aligning the side edge of the plate with the line on the plate guiding seal. Plate guiding seal TDP-459 Tear off and remove the seal completely. Entry of fragments of the seal into the feed path can cause trouble in feeding and/or printing. [Useful tip] When the end of the plate is inserted into the plate feeding port, the motor starts to operate to assist the feeding of the plate. The motor will stop when the plate setting is completed. When the plate setting is completed, the ”NG” LED lamp goes off and “OK” LED lamp turns on. - 20 - LED
- Page 2: Introduction Thank you for purchasi
- Page 5 and 6: Table of Contents Chapter 5 Trouble
- Page 7 and 8: Chapter 1 Safety Precautions 1.1 Ca
- Page 9 and 10: Chapter 1 Safety Precautions Use on
- Page 11 and 12: Chapter 1 Safety Precautions 1.4 Ha
- Page 13 and 14: Chapter 2 Installation and Setup Ch
- Page 15 and 16: Chapter 2 Installation and Setup 2.
- Page 17 and 18: Chapter 2 Installation and Setup I
- Page 19 and 20: Chapter 2 Installation and Setup 2.
- Page 21 and 22: Chapter 2 Installation and Setup 2.
- Page 23: Chapter 2 Installation and Setup 5.
- Page 27 and 28: Chapter 2 Installation and Setup 2.
- Page 29 and 30: Chapter 3 Use of Operation Panel TD
- Page 31 and 32: Chapter 3 Use of Operation Panel 3.
- Page 33 and 34: Chapter 3 Use of Operation Panel 3.
- Page 35 and 36: Chapter 3 Use of Operation Panel 3.
- Page 37 and 38: Chapter 3 Use of Operation Panel 3.
- Page 39 and 40: Chapter 3 Use of Operation Panel 5.
- Page 41 and 42: Chapter 3 Use of Operation Panel 3.
- Page 43 and 44: Chapter 4 Daily Maintenance Chapter
- Page 45 and 46: Chapter 4 Daily Maintenance < Clean
- Page 47 and 48: Chapter 4 Daily Maintenance 4.2 Cle
- Page 49 and 50: Chapter 5 Troubleshooting Chapter 5
- Page 51 and 52: Chapter 5 Troubleshooting When the
- Page 53 and 54: Chapter 5 Troubleshooting 5.3 When
- Page 55 and 56: Chapter 5 Troubleshooting 3. Wipe t
- Page 57 and 58: Chapter 6 After-sales service Chapt
- Page 59 and 60: Chapter 7 Specification Chapter 7 S
Chapter 2 Installation and Setup<br />
11. Remove the seal fixing the end of the<br />
plate.<br />
Fixing seal<br />
12. Feed in the plate by hand, aligning the<br />
side edge of the plate with the line on the<br />
plate guiding seal.<br />
Plate guiding seal<br />
<strong>TDP</strong>-<strong>459</strong><br />
Tear off and remove the seal completely.<br />
Entry of fragments of the seal into the feed<br />
path can cause trouble in feeding and/or<br />
printing.<br />
[Useful tip]<br />
When the end of the plate is inserted into the plate feeding port, the motor<br />
starts to operate to assist the feeding of the plate. The motor will stop when<br />
the plate setting is completed.<br />
When the plate setting is completed, the ”NG” LED lamp goes off and “OK”<br />
LED lamp turns on.<br />
- 20 -<br />
LED