TDP-459 Users Guide - MItsubishi Imaging
TDP-459 Users Guide - MItsubishi Imaging TDP-459 Users Guide - MItsubishi Imaging
2.2 Unpacking First, unpack and check the contents. - 9 - Chapter 2 Installation and Setup The box contains the Thermal Digiplater, accessories and protective inserts. The accessories are: Spool, Flange, power cable, USB cable, plate tray, users manual, the Windows driver CD-ROM with the users manual, the TDPController CD-ROM with the users manual, Technical Guide, and Product warranty. Accessories box Cushion Carton boxupper Joint (four places) Thermal Digiplater Cushion Carton box (lower) Pallet (made from corrugated paper) This Thermal Digiplater weighs approx. 55 kg (121lbs). Take care when handling it. When taking out and carrying, securely hold it by its bottom. Do not discard the packaging materials. The box and protective inserts will be required to transfer or transport the Thermal Digiplater. Keep them in a safe place. TDP-459
Chapter 2 Installation and Setup 2.3 Checking the accessories Take out the accessories from the box and from inside of the Thermal Digiplater. Check that the following items, as illustrated below, are present. TDP-459 Spool Flange(anti-gear side) Power cable USB cable Plate tray Users manual Windows driver CD-ROM Technical guide Flange(gear side) Spool shaft If an accessory is missing, contact the distributor immediately. - 10 - Product warranty TDPController CD-ROM
- Page 2: Introduction Thank you for purchasi
- Page 5 and 6: Table of Contents Chapter 5 Trouble
- Page 7 and 8: Chapter 1 Safety Precautions 1.1 Ca
- Page 9 and 10: Chapter 1 Safety Precautions Use on
- Page 11 and 12: Chapter 1 Safety Precautions 1.4 Ha
- Page 13: Chapter 2 Installation and Setup Ch
- Page 17 and 18: Chapter 2 Installation and Setup I
- Page 19 and 20: Chapter 2 Installation and Setup 2.
- Page 21 and 22: Chapter 2 Installation and Setup 2.
- Page 23 and 24: Chapter 2 Installation and Setup 5.
- Page 25 and 26: Chapter 2 Installation and Setup 11
- Page 27 and 28: Chapter 2 Installation and Setup 2.
- Page 29 and 30: Chapter 3 Use of Operation Panel TD
- Page 31 and 32: Chapter 3 Use of Operation Panel 3.
- Page 33 and 34: Chapter 3 Use of Operation Panel 3.
- Page 35 and 36: Chapter 3 Use of Operation Panel 3.
- Page 37 and 38: Chapter 3 Use of Operation Panel 3.
- Page 39 and 40: Chapter 3 Use of Operation Panel 5.
- Page 41 and 42: Chapter 3 Use of Operation Panel 3.
- Page 43 and 44: Chapter 4 Daily Maintenance Chapter
- Page 45 and 46: Chapter 4 Daily Maintenance < Clean
- Page 47 and 48: Chapter 4 Daily Maintenance 4.2 Cle
- Page 49 and 50: Chapter 5 Troubleshooting Chapter 5
- Page 51 and 52: Chapter 5 Troubleshooting When the
- Page 53 and 54: Chapter 5 Troubleshooting 5.3 When
- Page 55 and 56: Chapter 5 Troubleshooting 3. Wipe t
- Page 57 and 58: Chapter 6 After-sales service Chapt
- Page 59 and 60: Chapter 7 Specification Chapter 7 S
2.2 Unpacking<br />
First, unpack and check the contents.<br />
- 9 -<br />
Chapter 2 Installation and Setup<br />
The box contains the Thermal Digiplater, accessories and protective inserts.<br />
The accessories are: Spool, Flange, power cable, USB cable, plate tray, users manual, the Windows<br />
driver CD-ROM with the users manual, the <strong>TDP</strong>Controller CD-ROM with the users manual, Technical<br />
<strong>Guide</strong>, and Product warranty.<br />
Accessories box<br />
Cushion<br />
Carton boxupper<br />
Joint (four places)<br />
Thermal Digiplater<br />
Cushion<br />
Carton box (lower)<br />
Pallet<br />
(made from corrugated paper)<br />
This Thermal Digiplater weighs approx. 55 kg (121lbs). Take care when handling it.<br />
When taking out and carrying, securely hold it by its bottom.<br />
Do not discard the packaging materials. The box and protective inserts will be<br />
required to transfer or transport the Thermal Digiplater. Keep them in a safe place.<br />
<strong>TDP</strong>-<strong>459</strong>