om, rz3016, 2009-04, 966042901, zero turn, consumer - Husqvarna

More documents

Recommendations

Info

50 - Husqvarna WIRING DIAGRAM 8050-050
Engine crankshaft bolt 50 ft/lb (67 Nm) Deck pulley bolts 150 ft/lb (203 Nm) Lug nuts 75 ft/lb (100 Nm) Blade bolt 90 ft/lb (122 Nm) Shank Size (Diameter in inches, fine or coarse thread) tECHNICAL DAtA Torque Specifications Standard ¼" fasteners 9 ft/lb (12 Nm) Standard 5 /16" fasteners 18 ft/lb (25 Nm) Standard 3 /8" fasteners 33 ft/lb (44 Nm) Standard 7 /16" fasteners 52 ft/lb (70 Nm) Standard ½” fasteners 80 ft/lb (110 Nm) HEX HEAD CAP SCREWS The torque values shown should be used as a general guideline when specific torque values are not given. U.S. Standard Hardware Grade SAE Grade 5 SAE Grade 8 Flangelock Screw w/Flangelock Nut ft./lbs ft./lbs Nm ft./lbs Nm ft./lbs Nm ¼ 9 12 13 18 5 /16 18 24 28 38 24 33 3 /8 31 42 46 62 40 54 7 /16 50 68 75 108 ½ 75 102 115 156 9 /16 110 150 165 224 5 /8 150 203 225 305 ¾ 250 339 370 502 7 /8 378 513 591 801 1 1 /8 782 1060 1410 1912 ** Grade 5 - Minimum commercial quality (lower quality not recommended) Shank Size (Diameter in inches, fine or coarse thread) Metric Standard Hardware Grade Grade 8.8 Grade 10.9 Grade 12.9 ft./lbs ft./lbs Nm ft./lbs Nm ft./lbs Nm M4 1.5 2 2.2 3 2.7 3.6 M5 3 4 4.5 6 5.2 7 M6 5.2 7 7.5 10 8.2 11 M7 8.2 11 12 16 15 20 M8 13.5 18 18.8 25 21.8 29 M10 24 32 35.2 47 43.5 58 M12 43.5 58 62.2 83 75 100 M14 70.5 94 100 133 119 159 M16 108 144 147 196 176 235 M18 142 190 202 269 242 323 M20 195 260 275 366 330 440 M22 276 368 390 520 471 628 M24 353 470 498 664 596 794 M27 530 707 474 996 904 1205 HUSQVARNA-51
Page 1 and 2: RZ 3016 Operator Manual 966042901 P
Page 3 and 4: INtRODUCtION ......................
Page 5 and 6: Congratulations thank you for purch
Page 7 and 8: these symbols are found on the mach
Page 9 and 10: WARNING! THIS CUTTING MACHINE IS CA
Page 11 and 12: Personal Safety Equipment • •
Page 13 and 14: Safe Handling of Gasoline to avoid
Page 15 and 16: • • • • • • • • •
Page 17 and 18: this operator’s manual describes
Page 19 and 20: Parking Brake the parking brake is
Page 21 and 22: Fuel Shut Off Valve the fuel shut o
Page 23 and 24: Read “Safety Instructions” sect
Page 25 and 26: Move the steering controls outward
Page 27 and 28: Slowly slide the choke control back
Page 29 and 30: Operating on Hills Read the Safety
Page 31 and 32: Stopping the Engine Allow the engin
Page 33 and 34: Maintenance Schedule the following
Page 35 and 36: Battery Your mower is equipped with
Page 37 and 38: Engine Cooling Air Intake Check tha
Page 39 and 40: EZT Belt To replace EZT belt Park t
Page 41 and 42: Caster Wheels Check every 200 hours
Page 43 and 44: Front Wheel Mount Lubricate with a
Page 45 and 46: Checking the Oil Level the importan
Page 47 and 48: tROUBLESHOOtING Problem Cause the e
Page 49: Winter Storage At the end of the mo
Page 53 and 54: Frame tECHNICAL DAtA RZ3016 / 96604
Page 55 and 56: SERVICE JOURNAL Action Date, mtr re
Page 64: P/N 115 161426 IR 04/02/09

om, rz3016, 2009-04, 966042901, zero turn, consumer - Husqvarna

Create successful ePaper yourself

Delete template?

Save as template?