om, rz3016, 2009-04, 966042901, zero turn, consumer - Husqvarna

More documents

Recommendations

Info

Oil Recommendations Using the proper type and weight of oil in the crankcase is extremely important. So is checking oil daily and changing oil regularly. Failure to use the correct oil, or using dirty oil, causes premature engine wear and failure. Use high quality detergent oil of API (American Petroleum Institute) service class SG, SH, SJ or higher. Select the viscosity based on the air temperature at the time of operation. IMPORTANT INFORMATION Using other than service class SG, SH, SJ or higher oil or extending oil change intervals longer than recommended can cause engine damage. IMPORTANT INFORMATION Synthetic oils meeting the listed classifications may be used with oil changes performed at the recommended intervals. However to allow piston rings to properly seat, a new or rebuilt engine should be operated for at least 50 hours using standard petroleum based oil before switching to synthetic oil. A logo or symbol on oil containers identifies the API service class and SAE viscosity grade. Steering Control Shafts tip the driver’s seat. Lubricate with a grease gun, one zerk for each steering control shaft, until the grease is forced out. Use only good quality molybdenum disulphide grease. Grease from well-known brand names (petrochemical companies, etc.) usually maintains a good quality. 46 - HUSQVARNA LUBRICAtION Recommended SAE viscosity grades ** * 5W-20, 5W-30 10W-30 Kohler “Command” F -20 0 20 32 40 60 80 100 C -30 -20 -10 4 0 10 20 30 0 Temperature range expected before next oil change * Use of synthetic oil having 5W-20 or 5W-30 rating is acceptable, up to 40° F(+4° C). ** Synthetic oils will provide better starting in extreme cold below -10° F (-23° C). Viscosity grades table Lubricating the steering control shafts 8011-766a 8050-021
tROUBLESHOOtING Problem Cause the engine will not start. Blade lever is engaged. Steering controls are not locked in neutral position. Driver is not sitting in driver’s seat. Parking brake is not activated. Battery is dead. Contamination in carburetor or fuel line. Fuel supply is closed or tap for fuel tank is in wrong position. Clogged fuel filter or fuel line. the starter does not turn the engine over. Dead battery. Poor contacts on the battery terminal cable connections. Fuse blown. Ignition system faulty. Fault in the starter safety circuit. See Checking the Safety System in the “Maintenance Section” the engine runs rough. Faulty carburetor. Choke control used with warm engine. Defective valves. Defective piston, cylinder, piston ring, or cylinder head seal. Cylinder head bolts are loose. Clogged fuel filter or jet. Clogged ventilation valve on fuel cap. Fuel tank nearly empty. Fouled spark plug. Spark plug is loose. Defective ignition cable. Defective spark plug electrode. Defective spark plug connection. Rich fuel mixture or fuel-air mixture. Wrong fuel type. Water in fuel. Clogged air filter. HUSQVARNA-47
Page 1 and 2: RZ 3016 Operator Manual 966042901 P
Page 3 and 4: INtRODUCtION ......................
Page 5 and 6: Congratulations thank you for purch
Page 7 and 8: these symbols are found on the mach
Page 9 and 10: WARNING! THIS CUTTING MACHINE IS CA
Page 11 and 12: Personal Safety Equipment • •
Page 13 and 14: Safe Handling of Gasoline to avoid
Page 15 and 16: • • • • • • • • •
Page 17 and 18: this operator’s manual describes
Page 19 and 20: Parking Brake the parking brake is
Page 21 and 22: Fuel Shut Off Valve the fuel shut o
Page 23 and 24: Read “Safety Instructions” sect
Page 25 and 26: Move the steering controls outward
Page 27 and 28: Slowly slide the choke control back
Page 29 and 30: Operating on Hills Read the Safety
Page 31 and 32: Stopping the Engine Allow the engin
Page 33 and 34: Maintenance Schedule the following
Page 35 and 36: Battery Your mower is equipped with
Page 37 and 38: Engine Cooling Air Intake Check tha
Page 39 and 40: EZT Belt To replace EZT belt Park t
Page 41 and 42: Caster Wheels Check every 200 hours
Page 43 and 44: Front Wheel Mount Lubricate with a
Page 45: Checking the Oil Level the importan
Page 49 and 50: Winter Storage At the end of the mo
Page 51 and 52: Engine crankshaft bolt 50 ft/lb (67
Page 53 and 54: Frame tECHNICAL DAtA RZ3016 / 96604
Page 55 and 56: SERVICE JOURNAL Action Date, mtr re
Page 64: P/N 115 161426 IR 04/02/09

om, rz3016, 2009-04, 966042901, zero turn, consumer - Husqvarna

Create successful ePaper yourself

Delete template?

Save as template?