product guide - M-Audio

PRODUCT GUIDE 2009
84
PRODUCT SPECIFICATIONS
Dimensions:
8.75” (222.25 mm) x 6” (152.4 mm) x 7.25” (184.15 mm)
Weight: 14 lbs (6.34 kg)
Studiophile BX5a Deluxe
Frequency Response: 56Hz to 22kHz
Crossover Frequency: 3kHz
LF Amplifi er Power: 40 watts
HF Amplifi er Power: 30 watts
Signal-to-Noise Ratio: >100dB (typical A-weighted
Polarity:
positive signal @ + input produces outward LF cone
displacement
Input Impedance:
20k ohms, balanced; 10k ohms, unbalanced
Input Sensitivity: 85mV pink noise input produces
90dBA output SPL @ one meter with volume control @ max
Power:
factory programmed for either 115V ~50/60Hz, 230V~50/60Hz
Protection: RF interference, output current
limiting, over temperature, turn-on/off transient, subsonic fi lter,
external mains fuse
Cabinet: vinyl-laminated MDF
Dimensions:
9.84” (250 mm) x 6.93” (176 mm) x 7.87” (200 mm)
Weight: 11.0 lbs (5.0 kg)
Studiophile BX8a Deluxe
Frequency Response: 30Hz to 24kHz
Crossover Frequency: 2.2kHz
LF Amplifi er Power: 70 watts
HF Amplifi er Power: 60 watts
Signal-to-Noise Ratio: >100dB (typical A-weighted)
Polarity: positive signal @ + input produce
outward LF cone displacement
Input Impedance:
20k ohms, balanced; 10k ohms, unbalanced
Input Sensitivity: 85mV pink noise input produces
90dBA output SPL @ one meter with volume control @ max
Power: factory programmed for either 115V
~50/60Hz or 230V ~50/60Hz
Protection: RF interference, output current
limiting, over temperature, turn-on/off transient, subsonic fi lter,
external mains fuse
Cabinet: vinyl-laminated MDF
Dimensions:
12” (304.8 mm) x 10” (254 mm) x 15” (381 mm)
Weight: 26.4 lbs (11.97 kg)
Studiophile BX10s
Type:
bass-refl ex active powered subwoofer
Woofer Driver: 10-inch composite (treated paper/
fi berglass) cone with high-temperature voice coil and damped
rubber surround
Frequency Response: 20Hz to 200Hz (-3dB points)
Crossover: HP/LP linked fi lter sweepable from
50 to 200Hz; 24dB/octave 4th-order alignment
Input Sensitivity: 85mV pink noise input produces
100dBA output SPL @ one meter with volume control @ max
Amplifi er: 240 watts average power into 8
ohms, discrete transistor design
Gain: 36dB
Signal-to-Noise Ratio: 86dB A-weighted
THD @ Rated Power, Mono Mode: 0.019% (175 watts)
Inputs: two XLR balanced inputs; two TRS
balanced/unbalanced inputs
Outputs: two XLR balanced outputs for
satellites; two TRS balanced/unbalanced outputs for satellites
Controls: volume/gain control, 10dB bass
boost switch, sleep mode switch, phase inverse switch, variable
crossover control, subwoofer bypass footswitch jack
Input Impedance:
20k ohms balanced, 10k ohms unbalanced
Max Input Level: +20dBU
Auto Turn Off Time: 15 minutes
Auto Turn On Input
Sensitivity: 7.3mV
Protection: over temperature, turn-on/off
transient, subsonic fi lter, external mains fuse, DC protection, over
current protection
Indicator:
power on (blue) or standby/bypass (red)
Power: dual-voltage (selectable by rear-panel
switch) for either 100-120V/~50/60Hz or 220-240V/~50/60Hz;
powered via detachable
grounded IEC cable
Cabinet: vinyl-laminated MDF
Dimensions:
15” (381 mm) x 15” (381 mm) x 15” (381 mm)
Weight: 54.6 lbs (24.75 kg)
Studiophile DSM1
General
Frequency Response: 49Hz to 27kHz
Peak SPL @ 1 Meter: 110dB
LF Driver:
6.5” (165.1 mm) domeless anodized aluminum cone
HF Driver: 1” (25.4 mm) soft Teteron dome with
Neodymium magnet and ferrofl uid cooling
Crossover Frequency: 2.7kHz @ 24dB/octave
HF shelf: +1.5dB, -1.5dB, -3.0dB
Mid EQ: +1.5dB, -1.5dB, -3.0dB
High-Pass Filter:
40Hz, 60Hz, 80Hz, 100Hz @ 12dB/octave
Acoustic Space
Control Filter: -1.5dB, -3.0dB, -4.5dB
Desk EQ Filter 1: -1.0dB, -2.0dB, -3.0dB @ 220Hz
Desk EQ Filter 2: -1.0dB, -2.0dB, -3.0dB @ 175Hz
Desk EQ Filter 3: -1.0dB, -2.0dB, -3.0dB @ 200Hz
Analog Inputs: XLR balanced and 1/4” balanced
Digital Inputs: S/PDIF and AES/EBU
Input Impedance: 20k ohms
Input Sensitivity:
+4dBu yields 90dB @ 1 meter (trim level set to 0)
Gain Trim: volume trim from -22dB to +10dB
Dimensions:
12.8” (325.5 mm) x 9” (228.7 mm) x 10.3” (261.5 mm)
Weight: 16.5 lbs (7.5 kg)
Analog-to-Digital Specifi cations
Max Input Level: 18dBu
Signal-to-Noise Ratio: 102dB A-weighted
THD+N: 92dB
Conversion Rate: 96kHz
Digital Power Amplifi er
Output Power (1% THD): LF: 100 watts, HF: 80 watts
THD+N (10 watts, 1kHz): 90%
Studiophile DSM2
General
Frequency Response: 42Hz to 27kHz
Peak SPL @ 1 Meter: 111dB
LF Driver:
8” (203.2 mm) domeless anodized aluminum cone
HF Driver: 1” (25.4 mm) soft Teteron dome with
Neodymium magnet and ferrofl uid cooling
Crossover Frequency: 2.7kHz @ 24dB/octave
HF Shelf: +1.5dB, -1.5dB, -3.0dB
Mid EQ: +1.5dB, -1.5dB, -3.0dB
High-Pass Filter:
40Hz, 60Hz, 80Hz, 100Hz @ 12dB/octave
Acoustic Space
Control Filter: -1.5dB, -3.0dB, -4.5dB
Desk EQ Filter 1: -1.0dB, -2.0dB, -3.0dB @ 220Hz
Desk EQ Filter 2: -1.0dB, -2.0dB, -3.0dB @ 175Hz
Desk EQ Filter 3: -1.0dB, -2.0dB, -3.0dB @ 200Hz
Analog Inputs: XLR balanced and 1/4” balanced
Digital Inputs: S/PDIF and AES/EBU
Input Impedance: 20k ohms
Input Sensitivity:
+4dBu yields 90dB @ 1 meter (trim level set to 0)
Gain Trim: volume trim from -22dB to +10dB
Dimensions:
15.2” (385 mm) x 10.6” (270.3 mm) x 10.1” (257.5 mm)
Weight: 20 lbs (9.1 kg)
Analog-to-Digital Specifi cations
Max Input Level: 18dBu
Signal-to-Noise Ratio: 102dB A-weighted
THD+N: 92dB
Conversion Rate: 96kHz
Digital Power Amplifi er
Output Power (1% THD): LF: 100 watts, HF: 80 watts
THD+N (10 watts, 1kHz): 90%
Studiophile Q40
Frequency Response: 10Hz to 20kHz
Sensitivity: 116dB SPL (1mW IEC318)
Rated Impedance: 64 ohms
Weight Without Cable: 8.8 oz (.25 kg)
Magnet Material: neodymium
Driver: 40mm Mylar
TimewARP 2600
Windows
Windows XP
1.5GHz
256MB RAM, 1024 x 768 screen resolution
Mac
Mac OS X 10.3 or greater
1GHz
Compatibility
RTAS, VST, AU
Torq
Minimum System Requirements*
Windows XP
Windows XP (SP3)
Pentium IV 1.4GHz, 512MB RAM
One available USB port (for use by approved M-Audio
hardware device)
Windows Vista 32-Bit
Windows Vista 32-Bit
Pentium IV 1.8GHz, 1GB RAM
One available USB port (for use by approved M-Audio
hardware device)
Windows Experience Index of 3.0 or better
Windows Vista 64-Bit
Windows Vista 64-Bit
Pentium IV 1.8GHz, 1GB RAM
One available USB port (for use by approved M-Audio
hardware device)
Windows Experience Index of 3.0 or better
Mac
Mac OS X 10.4.11
G4 1.67GHz, 512MB RAM
One available USB port (for use by approved M-Audio
hardware device)
Mac users are strongly advised to pre-analyze all audio fi les prior
to use in Torq.
Mac G4 users are advised to not open the Timecode Preferences
Dialog while streaming more than one timecode source into Torq,
as this may degrade G4 performance. The user is advised to
calibrate before performing, one timecode source at a time.
*Minimum System Requirements refl ect the ability to run Torq
using a basic feature set. Some advanced or intensive features
will require increased system specifi cations.
Torq Conectiv
Mic Inputs (A/D)
Input Impedance: 340k ohms
Max Input Level: +4.1dBu (1.243 Vrms), min gain
Signal-to-Noise Ratio: -98dB, A-weighted
Dynamic Range: 98dB, A-weighted
THD+N:
0.00686% (-83.3dB) @ -1dBFS, 1kHz
Frequency Response:
20Hz to 20kHz, +/-0.2dB @ 48kHz sample rate
Preamp Variable Gain: >25dB
Phono Inputs (A/D)
Input Impedance: 48k ohms
EQ: RIAA curve
Gain: 43dB
Line Inputs (A/D)
Input Impedance: 48k ohms
Max Input Level, Min Gain: +10dBV (3.162 Vrms), unbalanced
Channel-to-Channel
Crosstalk: