Stateful Switchover.pdf - Cisco Learning Home
Stateful Switchover.pdf - Cisco Learning Home
Stateful Switchover.pdf - Cisco Learning Home
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Configuration Tasks<br />
Step 5 Perform this step on the <strong>Cisco</strong> 7500 series<br />
routers only:<br />
34<br />
Command Purpose<br />
no hw-module slot slot-number image<br />
file-spec<br />
Example:<br />
Router(config)# no hw-module slot 6 image<br />
slot0:rsp-pv-mz<br />
Step 6 Perform this step on the <strong>Cisco</strong> 7500 series<br />
routers only:<br />
no hw-module slot slot-number image<br />
file-spec<br />
Example:<br />
Router(config)# no hw-module slot 7 image<br />
slot0:rsp-pv-mz<br />
Step 7 Perform this step on the <strong>Cisco</strong> 7500 series<br />
routers only:<br />
hw-module slot slot-number image<br />
file-spec<br />
Example:<br />
Router(config)# hw-module slot 6 image<br />
slot0:image1<br />
Step 8 Perform this step on the <strong>Cisco</strong> 7500 series<br />
routers only:<br />
hw-module slot slot-number image<br />
file-spec<br />
Example:<br />
Router(config)# hw-module slot 7 image<br />
slot0:image1<br />
Step 9 no boot system flash<br />
[flash-fs:][partition-number:][filename]<br />
Example:<br />
Router(config)# no boot system flash<br />
Step 10 boot system flash<br />
[flash-fs:][partition-number:][filename]<br />
Example:<br />
Router(config)# boot system flash<br />
<strong>Stateful</strong> <strong>Switchover</strong><br />
<strong>Stateful</strong> <strong>Switchover</strong><br />
Clears existing configuration entries for the specified image on<br />
the standby RSP. Configuration entries are additive, and the<br />
networking device will use the first image found in the<br />
configuration file.<br />
• slot-number—Specifies the standby processor slot where the<br />
Flash memory card is located. Valid numbers are slot 2 or slot<br />
3 for a <strong>Cisco</strong> 7507 router or slot 6 or slot 7 for a <strong>Cisco</strong> 7513<br />
router.<br />
• file-spec—Indicates the Flash device and the name of the<br />
image on the standby processor.<br />
Clears existing configuration entries for the specified image on<br />
the active RSP. Configuration entries are additive, and the<br />
networking device will use the first image found in the<br />
configuration file.<br />
• slot-number—Specifies the active RSP slot where the Flash<br />
memory card is located. Valid numbers are slot 2 or slot 3 for<br />
a <strong>Cisco</strong> 7507 router or slot 6 or slot 7 for a <strong>Cisco</strong> 7513 router.<br />
• file-spec—Indicates the Flash device and the name of the<br />
image of the active processor.<br />
Specifies the image to be used by the standby RSP at<br />
initialization. If a high-availability image is found, the running<br />
configuration is updated.<br />
• slot-number—Specifies the standby RSP slot where the Flash<br />
memory card is located. Valid numbers are slot 2 or slot 3 for<br />
a <strong>Cisco</strong> 7507 router or slot 6 or slot 7 for a <strong>Cisco</strong> 7513 router.<br />
• file-spec—Indicates the Flash device and the name of the<br />
image on the standby processor.<br />
Specifies the image to be used by the active RSP at initialization.<br />
If a high-availability image is found, the running configuration is<br />
updated.<br />
• slot-number—Specifies the active RSP slot where the Flash<br />
memory card is located. Valid numbers are slot 2 or slot 3 for<br />
a <strong>Cisco</strong> 7507 router or slot 6 or slot 7 for a <strong>Cisco</strong> 7513 router.<br />
• file-spec—Indicates the Flash device and the name of the<br />
image of the active processor.<br />
Clears the current boot image filename from the configuration<br />
file.<br />
Specifies the filename of a boot image stored in Flash memory.
Change language