Ver.1.03 - Konica Minolta

More documents

Recommendations

Info

Necessary information to perform License operation You need to get necessary information for each operation and send it to MFP and LMS to execute the license operations. Following chart shows necessary information for each operation. Activation Deactivation Repair Initialization To LMS From LMS Serial Number X X X X X Token Number X X X(*1) X(*2) X Request Code X X X X License Code X X(*1) X(*2) X Deactivation code X X Deactivation Complete Code X X Repair Request Code (Repair Demand Code) Repair Code (Repair Permission Code) X X X X Initialization Code X X(*3) *1 If you exchange NVRAM when performing Repair, you need this information. *2 Require when re-activate the functions after the initialization. *3 Necessary to contact the support to acquire the code. Explanation of those Numbers used on those operations/ Codes are as follows. Serial Number Serial Number for MFP body. Token Number Token Number is printed on the Token Kit, or will be informed when purchasing the license. You need this number to enable License Activation Base Functions. Request Code This is ID Number to recognize the individual MFP. Serial Number information is also included in the Request Code. License Management Server (LMS) The Server performs license management. When you activate/ deactivate or make other operations for License Activation Base Functions, you need to access the License Management Server (Web site). Issued by BT-CSO 6 Ver 1.03
License Code Use this code to MFP when you activate License Activation Base Functions. License Management Server (LMS) issues this code. Deactivation Code This code is issued from LMS. This code is prepared on LMS when the necessary information is entered in LMS. After receiving the code, you need to enter it in MFP through the control panel to perform the deactivation. Deactivation Complete Code The information indicates to let LMS know the deactivation operation has been complete properly. MFP issues this code. Repair Request Code (Repair Demand Code) On the Service activates the error of license management state may be detected, and it is displayed on the control panel. At this time, you need to issue Repair Request to LMS. The information issued to request the Repair Code (Repair Permission Code). Repair Code (Repair Permission Code) When you enter the Repair Request Code (Repair Demand Code) to LMS, information to solve the error of license management state is issued from LMS. This information is Repair Code (Repair Permission Code). Initialization Code In the event that the error of license management state is not resolved, the license has to be reset to the initial condition forcibly. The information used to do it is the initialization code and issued from LMS. After that, it is necessary to activate the license again, to use the functions. Issued by BT-CSO 7 Ver 1.03
Page 1 and 2: izhub C203/C253/C353/C451/C550/C650
Page 3 and 4: • Necessary Information .........
Page 5: It is possible to execute this oper
Page 9 and 10: Requirements for using License Acti
Page 11 and 12: Necessary Information Serial Numbe
Page 13 and 14: Activation using [License Install U
Page 15 and 16: 1. Gather information from MFP/ Kit
Page 17 and 18: d) Select [Yes] and press [OK]. e)
Page 21 and 22: d) Select the display Language. e)
Page 23 and 24: l) Click [Print] button to print th
Page 25 and 26: d) Select [Select Function]. e) Sel
Page 27 and 28: l) After rebooting MFP, check the f
Page 29 and 30: g) After rebooting MFP, check the f
Page 31 and 32: Deactivation This is the operation
Page 33 and 34: Flow chart for Deactivation There
Page 35 and 36: Deactivation Procedure The followin
Page 39 and 40: h) Activated function list of MFP (
Page 41 and 42: e) Select the License Kit that need
Page 43 and 44: d) Enter the [E-Mail Address] and t
Page 45 and 46: Repair After replacement of the par
Page 47 and 48: Flow chart for Repair There are 3
Page 49 and 50: c) Select [Repair Request Code (Rep
Page 51 and 52: d) Enter the [E-Mail Address] and [
Page 53 and 54: 1. Gather information from MFP 2. A
Page 55 and 56: Issued by BT-CSO 55 Ver 1.03
Page 57 and 58:
Initialization code (35 digits) Th
Page 59 and 60:
[Initialization Procedure] The foll
Page 61 and 62:
d) Select [Yes] and press [OK]. e)
Page 63 and 64:
1. Gather necessary information 1-1
Page 65 and 66:
1. Gather necessary information 2.
Page 67 and 68:
Operation procedure when executing
show all

Ver.1.03 - Konica Minolta

Create successful ePaper yourself

Delete template?

Save as template?