Ver.1.03 - Konica Minolta

More documents

Recommendations

Info

h) Click [OK]. By pressing [Cancel], it is possible to correct what was entered. i) When this screen is displayed, register of Deactivation Complete Code to LMS is completed. The Deactivation operation completed. Issued by BT-CSO 44 Ver 1.03
Repair After replacement of the parts, the message “License Management Error occurred” may be displayed on the control panel. When it the message appear, it is necessary to perform repair operation. The repair operation can be done with accessing LMS. When those parts as listed below is replaced, the message “License Management Error ” may be displayed. When replacing those parts below, please replace it with new parts. When the parts are replaced with used parts, the message condition can not be solved by performing the repair operation. NVRAM Service EEPROM Board If License Activation Base function was already activated While the error message is indicated on the control panel, the License Activation Base Function will not be disabled. When the error message is indicated after replacement of the NVRAM, License Activation is required after the completion of the repair operation to use the function again. If License Activation Base function was not activated Even the function was not activated, the message may be indicated if those parts mentioned before is replaced. MFP can be used without the repair operation, but to solve it, the repair operation is required. Overview of Repair Operation With accessing LMS with the web browser, it is necessary to enter the Serial number, Request Code, and Repair Request Code. Then LMS issues Repair Code. With using the Repair Code issued from LMS, the repair operation will be preformed. To perform repair operation, the code has to input in the MFP through the control panel. Who to perform the operation Customer engineer or sales person MFP To access to LMS for repair operation, user ID and password is required. LMS [Serial Number] [Repair request code] [Request Code] Input [Repair Code] Repair Output Issued by BT-CSO 45 Ver 1.03 Input
Page 1 and 2: izhub C203/C253/C353/C451/C550/C650
Page 3 and 4: • Necessary Information .........
Page 5 and 6: It is possible to execute this oper
Page 7 and 8: License Code Use this code to MFP w
Page 9 and 10: Requirements for using License Acti
Page 11 and 12: Necessary Information Serial Numbe
Page 13 and 14: Activation using [License Install U
Page 15 and 16: 1. Gather information from MFP/ Kit
Page 17 and 18: d) Select [Yes] and press [OK]. e)
Page 21 and 22: d) Select the display Language. e)
Page 23 and 24: l) Click [Print] button to print th
Page 25 and 26: d) Select [Select Function]. e) Sel
Page 27 and 28: l) After rebooting MFP, check the f
Page 29 and 30: g) After rebooting MFP, check the f
Page 31 and 32: Deactivation This is the operation
Page 33 and 34: Flow chart for Deactivation There
Page 35 and 36: Deactivation Procedure The followin
Page 39 and 40: h) Activated function list of MFP (
Page 41 and 42: e) Select the License Kit that need
Page 43: d) Enter the [E-Mail Address] and t
Page 47 and 48: Flow chart for Repair There are 3
Page 49 and 50: c) Select [Repair Request Code (Rep
Page 51 and 52: d) Enter the [E-Mail Address] and [
Page 53 and 54: 1. Gather information from MFP 2. A
Page 55 and 56: Issued by BT-CSO 55 Ver 1.03
Page 57 and 58: Initialization code (35 digits) Th
Page 59 and 60: [Initialization Procedure] The foll
Page 61 and 62: d) Select [Yes] and press [OK]. e)
Page 63 and 64: 1. Gather necessary information 1-1
Page 65 and 66: 1. Gather necessary information 2.
Page 67 and 68: Operation procedure when executing

Ver.1.03 - Konica Minolta

Create successful ePaper yourself

Delete template?

Save as template?