Ver.1.03 - Konica Minolta

More documents

Recommendations

Info

About this guidebook From Mosel/ Thames i-Option firmware, the license activation system is newly adopted. Some additional functions will be available after the license activation. This guidebook explains outline and operation procedure of License Management. i-Option firmware is also including some additional functions that can be used without the authentication. For the explanation of those functions. Please refer to the PRI for the firmware. Outlines of Functions New “License Activation Base Functions” are included in Mosel/ Thames i-Option firmware. Activation Base Functions have several types of functions. (Please refer to the functions listed below.) Those functions are included in the firmware. If you purchase the license and activate the License Activation Base Functions, the functions will be available. Also, the function enhancements do not necessary Activation are included in the firmware. About those functions, please refer to not this guidebook but PRI distributed with the firmware or the following chapter. License Activation Base Functions In this guidebook, the functions like “LK-101, LK-102, LK-103” (You need to purchase the license when using these functions.) are called “License Activation Base Functions”. LK-101 Web browser function, Image panel, and it is possible to register the picture (thumbnail) in the address book on the image panel. LK-102 Enhancement of PDF encryption (response to public key and AES, function that can write title/ creator when sending PDF file, etc.) LK-103 LK-103 Includes “LK-101” and “LK-102”. License Operations When you start, stop or repair using the license activation base functions, those operations, Activation, Deactivation, Repair or Initialization, have to be made as you intended. There are 4 types of License Operations. License Operations Activation This is the operation to enable License Activation Base Functions and make the functions operational. Issued by BT-CSO 4 Ver 1.03
It is possible to execute this operation in Administrator Mode or Service Mode. Deactivation This is the operation to invalidate the activated License Activation Base Functions. It is possible to execute this operation in Service Mode. Repair It is necessary to execute this operation when the error of license management state is displayed on the control panel. If it occurs, the License Activation Base Functions are temporarily disabled. To recover the condition, Repair operation has to be performed. It is possible to execute this operation in Service Mode. Initialization Execute this operation when the error state is not resolved after performing Repair. Basically, execute Initialization only when the error of license management state occurs after performing Repair. When performing the operation, please confirm that the error of license management state occurs under what conditions (executed operations, parts replacement, setting change and so on). It is possible to execute this operation in Service Mode. Issued by BT-CSO 5 Ver 1.03
Page 1 and 2: izhub C203/C253/C353/C451/C550/C650
Page 3: • Necessary Information .........
Page 7 and 8: License Code Use this code to MFP w
Page 9 and 10: Requirements for using License Acti
Page 11 and 12: Necessary Information Serial Numbe
Page 13 and 14: Activation using [License Install U
Page 15 and 16: 1. Gather information from MFP/ Kit
Page 17 and 18: d) Select [Yes] and press [OK]. e)
Page 21 and 22: d) Select the display Language. e)
Page 23 and 24: l) Click [Print] button to print th
Page 25 and 26: d) Select [Select Function]. e) Sel
Page 27 and 28: l) After rebooting MFP, check the f
Page 29 and 30: g) After rebooting MFP, check the f
Page 31 and 32: Deactivation This is the operation
Page 33 and 34: Flow chart for Deactivation There
Page 35 and 36: Deactivation Procedure The followin
Page 39 and 40: h) Activated function list of MFP (
Page 41 and 42: e) Select the License Kit that need
Page 43 and 44: d) Enter the [E-Mail Address] and t
Page 45 and 46: Repair After replacement of the par
Page 47 and 48: Flow chart for Repair There are 3
Page 49 and 50: c) Select [Repair Request Code (Rep
Page 51 and 52: d) Enter the [E-Mail Address] and [
Page 53 and 54: 1. Gather information from MFP 2. A
Page 55 and 56:
Issued by BT-CSO 55 Ver 1.03
Page 57 and 58:
Initialization code (35 digits) Th
Page 59 and 60:
[Initialization Procedure] The foll
Page 61 and 62:
d) Select [Yes] and press [OK]. e)
Page 63 and 64:
1. Gather necessary information 1-1
Page 65 and 66:
1. Gather necessary information 2.
Page 67 and 68:
Operation procedure when executing
show all

Ver.1.03 - Konica Minolta

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?