Xilinx Synthesis Technology User Guide

More documents

Recommendations

Info

XST <strong>User</strong> <strong>Guide</strong> Sequential Circuits Sequential circuits can be described using sequential processes. The following two types of descriptions are allowed by XST: • sequential processes with a sensitivity list • sequential processes without a sensitivity list Sequential Process with a Sensitivity List A process is sequential when it is not a combinatorial process. In other words, a process is sequential when some assigned signals are not explicitly assigned in all paths of the statements. In this case, the hardware generated has an internal state or memory (flip-flops or latches). Example 6-15 provides a template for describing sequential circuits. Also refer to the chapter describing macro inference for additional details (registers, counters, etc.). Example 6-15 Sequential Process with Asynchronous, Synchronous Parts process (CLK, RST) ... begin if RST = then -- an asynchronous part may appear here -- optional part ....... elsif
Sequential Process without a Sensitivity List VHDL Language Support Sequential processes without a sensitivity list must contain a "wait" statement. The "wait" statement must be the first statement of the process. The condition in the "wait" statement must be a condition on the clock signal. Several "wait" statements in the same process are accepted, but a set o f specific conditions must be respected. See the “Sequential Circuits” section for details. An asynchronous part can not be specified within processes without a sensitivity list. Example 6-16 shows the skeleton of such a process. The clock condition may be a falling or a rising edge. Example 6-16 Sequential Process Without a Sensitivity List process ... begin wait until
Page 1 and 2:
Xilinx Synthesis Technology (XST) U
Page 3 and 4:
About This Manual Manual Contents T
Page 5 and 6:
Resource Description/URL About This
Page 7 and 8:
Conventions Typographical This manu
Page 9 and 10:
Contents About This Manual Conventi
Page 11 and 12:
Contents 8-bit Shift-Left Register
Page 13 and 14:
Contents Dividers .................
Page 15 and 16:
Contents Verilog Flow: ............
Page 17 and 18:
Contents Sequential Process with a
Page 19 and 20:
Introduction Architecture Support X
Page 21 and 22:
Introduction 4. Set the desired Syn
Page 23 and 24:
Figure 1-1 View Synthesis Report In
Page 25 and 26:
HDL Coding Techniques This chapter
Page 27 and 28:
HDL Coding Techniques The following
Page 29 and 30:
Page 31 and 32:
Table 2-1 VHDL and Verilog Examples
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Signed/Unsigned Support Registers H
Page 39 and 40:
Flip-flop with Positive-Edge Clock
Page 41 and 42:
Page 43 and 44:
VHDL Code HDL Coding Techniques Fol
Page 45 and 46:
Page 47 and 48:
IO Pins Description CE Clock Enable
Page 49 and 50:
Log File HDL Coding Techniques The
Page 51 and 52:
HDL Coding Techniques Verilog Code
Page 53 and 54:
HDL Coding Techniques 4-bit Latch w
Page 55 and 56:
Tristates Log File HDL Coding Techn
Page 57 and 58:
Page 59 and 60:
Counters HDL Coding Techniques XST
Page 61 and 62:
Page 63 and 64:
HDL Coding Techniques 4-bit Unsigne
Page 65 and 66:
HDL Coding Techniques entity counte
Page 67 and 68:
Verilog Code HDL Coding Techniques
Page 69 and 70:
HDL Coding Techniques 4-bit Unsigne
Page 71 and 72:
Page 73 and 74:
Accumulators HDL Coding Techniques
Page 75 and 76:
Page 77 and 78:
HDL Coding Techniques • shift mod
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
HDL Coding Techniques 8-bit Shift-L
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Dynamic Shift Register module shift
Page 95 and 96:
library IEEE; use IEEE.std_logic_11
Page 97 and 98:
Page 99 and 100:
neither Full nor Parallel module no
Page 101 and 102:
Related Constraints Related constra
Page 103 and 104:
HDL Coding Techniques entity mux is
Page 105 and 106:
Page 107 and 108:
Decoders Log File HDL Coding Techni
Page 109 and 110:
VHDL (One-Cold) Following is the VH
Page 111 and 112:
VHDL Following is the VHDL code. li
Page 113 and 114:
Page 115 and 116:
Priority Encoders Log File HDL Codi
Page 117 and 118:
Verilog Logical Shifters HDL Coding
Page 119 and 120:
Example 1 HDL Coding Techniques The
Page 121 and 122:
Page 123 and 124:
Verilog Arithmetic Operations Follo
Page 125 and 126:
Unsigned 8-bit Adder HDL Coding Tec
Page 127 and 128:
HDL Coding Techniques Verilog Follo
Page 129 and 130:
Page 131 and 132:
Simple Signed 8-bit Adder HDL Codin
Page 133 and 134:
Unsigned 8-bit Adder/Subtractor HDL
Page 135 and 136:
Comparators (=, /=,=) HDL Coding Te
Page 137 and 138:
HDL Coding Techniques this, XST can
Page 139 and 140:
Dividers HDL Coding Techniques VHDL
Page 141 and 142:
Page 143 and 144:
B C A OPER +/- RES OPER X8984 HDL C
Page 145 and 146:
HDL Coding Techniques • RAM descr
Page 147 and 148:
HDL Coding Techniques entity raminf
Page 149 and 150:
HDL Coding Techniques VHDL The foll
Page 151 and 152:
HDL Coding Techniques Verilog The f
Page 153 and 154:
HDL Coding Techniques VHDL The foll
Page 155 and 156:
Page 157 and 158:
VHDL Following is the VHDL code for
Page 159 and 160:
HDL Coding Techniques Single-Port R
Page 161 and 162:
Verilog HDL Coding Techniques Follo
Page 163 and 164:
Page 165 and 166:
HDL Coding Techniques Single-Port R
Page 167 and 168:
Verilog Following is the Verilog co
Page 169 and 170:
VHDL HDL Coding Techniques Followin
Page 171 and 172:
Dual-Port RAM with Asynchronous Rea
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
HDL Coding Techniques Dual-Port RAM
Page 179 and 180:
Page 181 and 182:
HDL Coding Techniques architecture
Page 183 and 184:
HDL Coding Techniques Dual-Port RAM
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
VHDL Following is the VHDL code for
Page 197 and 198:
Inputs Next State Function RESET CL
Page 199 and 200:
FSM with 1 Process HDL Coding Techn
Page 201 and 202:
Inputs FSM with 2 Processes HDL Cod
Page 203 and 204:
Page 205 and 206:
process2 : process (state, x1) begi
Page 207 and 208:
State Registers HDL Coding Techniqu
Page 209 and 210:
Compact HDL Coding Techniques Compa
Page 211 and 212:
Black Box Support Log File HDL Codi
Page 213 and 214:
Page 215 and 216:
FPGA Optimization Introduction This
Page 217 and 218:
Macro Generation • Number of Cloc
Page 219 and 220:
Multiplexers FPGA Optimization For
Page 221 and 222:
RAMs FPGA Optimization Two types of
Page 223 and 224:
Flip-Flop Retiming FPGA Optimizatio
Page 225 and 226:
FPGA Optimization INCREMENTAL_SYNTH
Page 227 and 228:
FPGA Optimization Note In the curre
Page 229 and 230:
FPGA Optimization generated NGC fil
Page 231 and 232:
FPGA Optimization The problem most
Page 233 and 234:
Log File Analysis FPGA Optimization
Page 235 and 236:
FPGA Optimization • Tristates Thi
Page 237 and 238:
FPGA Optimization NOTE: THESE TIMIN
Page 239 and 240:
FPGA Optimization The start point a
Page 241 and 242:
FPGA Optimization If the box_type a
Page 243 and 244:
Instantiation of MUXF5 FPGA Optimiz
Page 245 and 246:
Page 247 and 248:
Specifying INITs and RLOCs in HDL C
Page 249 and 250:
FPGA Optimization for registers onl
Page 251 and 252:
PCI Flow FPGA Optimization To succe
Page 253 and 254:
CPLD Optimization This chapter cont
Page 255 and 256:
Implementation Details for Macro Ge
Page 257 and 258:
CPLD Optimization • Final results
Page 259 and 260:
CPLD Optimization The CPLD fitter m
Page 261 and 262:
Design Constraints Chapter 5 This c
Page 263 and 264:
Synthesis Options Design Constraint
Page 265 and 266:
Design Constraints Figure 5-4 Synth
Page 267 and 268:
• Mux Extraction • Mux Style
Page 269 and 270:
Design Constraints For FPGA device
Page 271 and 272:
XST Constraint File (XCF) Design Co
Page 273 and 274:
Design Constraints Timing Constrain
Page 275 and 276:
Design Constraints • Add IO Buffe
Page 277 and 278:
Design Constraints the components c
Page 279 and 280:
HDL Constraints Design Constraints
Page 281 and 282:
FPGA Constraints (non-timing) Desig
Page 283 and 284:
Design Constraints • Number of Cl
Page 285 and 286:
Design Constraints This constraint
Page 287 and 288:
Timing Constraints Design Constrain
Page 289 and 290:
Design Constraints See the “CLOCK
Page 291 and 292: Design Constraints The following ti
Page 293 and 294: Design Constraints • TIMEGRP TIME
Page 295 and 296: Design Constraints See the “INPAD
Page 297 and 298: Constraint Name clock_buffer bufgdl
Page 299 and 300: Constraint Name move_last- _stage m
Page 301 and 302: Constraint Name xor_collapse yes, n
Page 303 and 304: Constraint Name synthesis/ synopsis
Page 305 and 306: Design Constraints The following ta
Page 307 and 308: *Also Supported in XCF format. Impl
Page 309 and 310: Design Constraints The binary equiv
Page 311 and 312: Table 5-5 Third Party Constraints N
Page 313 and 314: Table 5-5 Third Party Constraints N
Page 315 and 316: Constraints Precedence Design Const
Page 317 and 318: VHDL Language Support Chapter 6 Thi
Page 319 and 320: VHDL Language Support 'W' means wea
Page 321 and 322: VHDL Language Support compiled in t
Page 323 and 324: Record Types Objects in VHDL MATRIX
Page 325 and 326: Entity Declaration VHDL Language Su
Page 327 and 328: VHDL Language Support Example 6-2 g
Page 329 and 330: VHDL Language Support Example 6-3 4
Page 331 and 332: egin Y 13), port map (X,Y,C1); C2
Page 333 and 334: VHDL Language Support Example 6-5 M
Page 335 and 336: VHDL Language Support Example 6-8 N
Page 337 and 338: Example 6-10 Combinatorial Process
Page 339 and 340: VHDL Language Support Example 6-12
Page 341: For...Loop Statement VHDL Language
Page 345 and 346: egin if RST = '1' then DO
Page 347 and 348: Multiple Wait Statements Descriptio
Page 349 and 350: Functions and Procedures VHDL Langu
Page 351 and 352: VHDL Language Support Example 6-24
Page 353 and 354: STANDARD Package VHDL Language Supp
Page 355 and 356: VHDL Language Support Note Function
Page 357 and 358: Packages Enumeration Types Integer
Page 359 and 360: Table 6-4 Objects VHDL Language Sup
Page 361 and 362: Wait Statement Loop Statement Table
Page 363 and 364: VHDL Reserved Words The following t
Page 365 and 366: Verilog Language Support Chapter 7
Page 367 and 368: Behavioral Verilog Features Verilog
Page 369 and 370: Verilog Language Support Example 7-
Page 371 and 372: Table 7-1 Expressions Bitwise Negat
Page 373 and 374: Modules Verilog Language Support In
Page 375 and 376: Procedural Assignments Verilog Lang
Page 377 and 378: Verilog Language Support Casez trea
Page 379 and 380: While Loops Verilog Language Suppor
Page 381 and 382: Verilog Language Support Example 7-
Page 383 and 384: Verilog Language Support The main l
Page 385 and 386: Verilog Language Support • You ca
Page 387 and 388: Example 7-9 Function Declaration an
Page 389 and 390: Blocking Versus Non-Blocking Proced
Page 391 and 392: Include Files Verilog Language Supp
Page 393 and 394:
Verilog Language Support Each insta
Page 395 and 396:
Parameters Verilog Language Support
Page 397 and 398:
Verilog Language Support • Design
Page 399 and 400:
Verilog Meta Comments Verilog Langu
Page 401 and 402:
Table 7-4 Data Types Registers Vect
Page 403 and 404:
Table 7-8 Design Hierarchy Module d
Page 405 and 406:
Verilog Reserved Keywords Verilog L
Page 407 and 408:
Command Line Mode Introduction Chap
Page 409 and 410:
Command Line Mode • Script File
Page 411 and 412:
Command Line Mode • Second column
Page 413 and 414:
Table 8-4 HDL Options (VHDL and Ver
Page 415 and 416:
Command Line Mode Table 8-6 Target
Page 417 and 418:
Command Line Mode • To get a list
Page 419 and 420:
Elaborate Command Time Command Comm
Page 421 and 422:
♦ smallcntr.vhd Command Line Mode
Page 423 and 424:
Command Line Mode You can improve t
Page 425 and 426:
Command Line Mode Sometimes, XST is
Page 427 and 428:
XST Shell Command Line Mode To use
Page 429 and 430:
Case 2 Command Line Mode Each desig
Page 431 and 432:
Log File Analysis Introduction This
Page 433 and 434:
Quiet Mode Timing Report Log File A
Page 435 and 436:
RAM Style : Auto ROM Extraction : y
Page 437 and 438:
Synthesizing Unit . Related source
Page 439 and 440:
# Counters : 2 # 4-bit up counter :
Page 441 and 442:
Log File Analysis Data Path: sixty_
Page 443 and 444:
CPLD Log File Log File Analysis The
Page 445 and 446:
Analyzing Entity (Architecture ).
Page 447 and 448:
Log File Analysis =================
Page 449 and 450:
XST Naming Conventions This appendi
show all

Xilinx Synthesis Technology User Guide

Create successful ePaper yourself

Delete template?

Save as template?