Xilinx Synthesis Technology User Guide

More documents

Recommendations

Info

XST User Guide Device Utilization summary Where XST estimates the number of slices, gives the number of FFs, IOBs, BRAMS, etc. This report is very close to the one produced by MAP. Clock Information A short table gives information about the number of clocks in the design, how each clock is buffered and how many loads it has. Timing Report At the end of the synthesis, XST reports the timing information for the design. The report shows the information for all four possible domains of a netlist: "register to register", "input to register", "register to outpad" and "inpad to outpad". The following is an example of a timing report section in the XST log: 3-22 Xilinx Development System
FPGA Optimization NOTE: THESE TIMING NUMBERS ARE ONLY A SYNTHESIS ESTIMATE. FOR ACCURATE TIMING INFORMATION PLEASE REFER TO THE TRACE REPORT GENERATED AFTER PLACE-and-ROUTE. Clock Information: ------------------ -----------------------------------+------------------------+-------+ Clock Signal | Clock buffer(FF name) | Load | -----------------------------------+------------------------+-------+ clk | BUFGP | 9 | -----------------------------------+------------------------+-------+ Timing Summary: --------------- Speed Grade: -6 Minimum period: 7.523ns (Maximum Frequency: 132.926MHz) Minimum input arrival time before clock: 8.945ns Maximum output required time after clock: 14.220ns Maximum combinational path delay: 10.889ns Timing Detail: -------------- All values displayed in nanoseconds (ns) ------------------------------------------------------------------------- Timing constraint: Default period analysis for Clock 'clk' Delay: 7.523ns (Levels of Logic = 2) Source: sdstate_FFD1 Destination: sdstate_FFD2 Source Clock: clk rising Destination Clock: clk rising Data Path: sdstate_FFD1 to sdstate_FFD2 Gate Net Cell:in->out fanout Delay Delay Logical Name (Net Name) ---------------------------------------- ------------ FDC:C->Q 15 1.372 2.970 state_FFD1 (state_FFD1) LUT3:I1->O 1 0.738 1.265 LUT_54 (N39) LUT3:I1->O 1 0.738 0.000 I_next_state_2 (N39) FDC:D 0.440 state_FFD2 ---------------------------------------- Total 7.523ns (3.288ns logic, 4.235ns route) (43.7% logic, 56.3% route) XST User Guide 3-23
Page 1 and 2:
Xilinx Synthesis Technology (XST) U
Page 3 and 4:
About This Manual Manual Contents T
Page 5 and 6:
Resource Description/URL About This
Page 7 and 8:
Conventions Typographical This manu
Page 9 and 10:
Contents About This Manual Conventi
Page 11 and 12:
Contents 8-bit Shift-Left Register
Page 13 and 14:
Contents Dividers .................
Page 15 and 16:
Contents Verilog Flow: ............
Page 17 and 18:
Contents Sequential Process with a
Page 19 and 20:
Introduction Architecture Support X
Page 21 and 22:
Introduction 4. Set the desired Syn
Page 23 and 24:
Figure 1-1 View Synthesis Report In
Page 25 and 26:
HDL Coding Techniques This chapter
Page 27 and 28:
HDL Coding Techniques The following
Page 29 and 30:
Page 31 and 32:
Table 2-1 VHDL and Verilog Examples
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Signed/Unsigned Support Registers H
Page 39 and 40:
Flip-flop with Positive-Edge Clock
Page 41 and 42:
Page 43 and 44:
VHDL Code HDL Coding Techniques Fol
Page 45 and 46:
Page 47 and 48:
IO Pins Description CE Clock Enable
Page 49 and 50:
Log File HDL Coding Techniques The
Page 51 and 52:
HDL Coding Techniques Verilog Code
Page 53 and 54:
HDL Coding Techniques 4-bit Latch w
Page 55 and 56:
Tristates Log File HDL Coding Techn
Page 57 and 58:
Page 59 and 60:
Counters HDL Coding Techniques XST
Page 61 and 62:
Page 63 and 64:
HDL Coding Techniques 4-bit Unsigne
Page 65 and 66:
HDL Coding Techniques entity counte
Page 67 and 68:
Verilog Code HDL Coding Techniques
Page 69 and 70:
HDL Coding Techniques 4-bit Unsigne
Page 71 and 72:
Page 73 and 74:
Accumulators HDL Coding Techniques
Page 75 and 76:
Page 77 and 78:
HDL Coding Techniques • shift mod
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
HDL Coding Techniques 8-bit Shift-L
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Dynamic Shift Register module shift
Page 95 and 96:
library IEEE; use IEEE.std_logic_11
Page 97 and 98:
Page 99 and 100:
neither Full nor Parallel module no
Page 101 and 102:
Related Constraints Related constra
Page 103 and 104:
HDL Coding Techniques entity mux is
Page 105 and 106:
Page 107 and 108:
Decoders Log File HDL Coding Techni
Page 109 and 110:
VHDL (One-Cold) Following is the VH
Page 111 and 112:
VHDL Following is the VHDL code. li
Page 113 and 114:
Page 115 and 116:
Priority Encoders Log File HDL Codi
Page 117 and 118:
Verilog Logical Shifters HDL Coding
Page 119 and 120:
Example 1 HDL Coding Techniques The
Page 121 and 122:
Page 123 and 124:
Verilog Arithmetic Operations Follo
Page 125 and 126:
Unsigned 8-bit Adder HDL Coding Tec
Page 127 and 128:
HDL Coding Techniques Verilog Follo
Page 129 and 130:
Page 131 and 132:
Simple Signed 8-bit Adder HDL Codin
Page 133 and 134:
Unsigned 8-bit Adder/Subtractor HDL
Page 135 and 136:
Comparators (=, /=,=) HDL Coding Te
Page 137 and 138:
HDL Coding Techniques this, XST can
Page 139 and 140:
Dividers HDL Coding Techniques VHDL
Page 141 and 142:
Page 143 and 144:
B C A OPER +/- RES OPER X8984 HDL C
Page 145 and 146:
HDL Coding Techniques • RAM descr
Page 147 and 148:
HDL Coding Techniques entity raminf
Page 149 and 150:
HDL Coding Techniques VHDL The foll
Page 151 and 152:
HDL Coding Techniques Verilog The f
Page 153 and 154:
HDL Coding Techniques VHDL The foll
Page 155 and 156:
Page 157 and 158:
VHDL Following is the VHDL code for
Page 159 and 160:
HDL Coding Techniques Single-Port R
Page 161 and 162:
Verilog HDL Coding Techniques Follo
Page 163 and 164:
Page 165 and 166:
HDL Coding Techniques Single-Port R
Page 167 and 168:
Verilog Following is the Verilog co
Page 169 and 170:
VHDL HDL Coding Techniques Followin
Page 171 and 172:
Dual-Port RAM with Asynchronous Rea
Page 173 and 174:
Verilog Following is the Verilog co
Page 175 and 176:
VHDL HDL Coding Techniques Followin
Page 177 and 178:
HDL Coding Techniques Dual-Port RAM
Page 179 and 180:
Verilog HDL Coding Techniques Follo
Page 181 and 182:
HDL Coding Techniques architecture
Page 183 and 184:
HDL Coding Techniques Dual-Port RAM
Page 185 and 186: Verilog HDL Coding Techniques Follo
Page 187 and 188: VHDL HDL Coding Techniques Followin
Page 191 and 192: VHDL HDL Coding Techniques Followin
Page 193 and 194: Verilog Following is the Verilog co
Page 195 and 196: VHDL Following is the VHDL code for
Page 197 and 198: Inputs Next State Function RESET CL
Page 199 and 200: FSM with 1 Process HDL Coding Techn
Page 201 and 202: Inputs FSM with 2 Processes HDL Cod
Page 205 and 206: process2 : process (state, x1) begi
Page 207 and 208: State Registers HDL Coding Techniqu
Page 209 and 210: Compact HDL Coding Techniques Compa
Page 211 and 212: Black Box Support Log File HDL Codi
Page 215 and 216: FPGA Optimization Introduction This
Page 217 and 218: Macro Generation • Number of Cloc
Page 219 and 220: Multiplexers FPGA Optimization For
Page 221 and 222: RAMs FPGA Optimization Two types of
Page 223 and 224: Flip-Flop Retiming FPGA Optimizatio
Page 225 and 226: FPGA Optimization INCREMENTAL_SYNTH
Page 227 and 228: FPGA Optimization Note In the curre
Page 229 and 230: FPGA Optimization generated NGC fil
Page 231 and 232: FPGA Optimization The problem most
Page 233 and 234: Log File Analysis FPGA Optimization
Page 235: FPGA Optimization • Tristates Thi
Page 239 and 240: FPGA Optimization The start point a
Page 241 and 242: FPGA Optimization If the box_type a
Page 243 and 244: Instantiation of MUXF5 FPGA Optimiz
Page 247 and 248: Specifying INITs and RLOCs in HDL C
Page 249 and 250: FPGA Optimization for registers onl
Page 251 and 252: PCI Flow FPGA Optimization To succe
Page 253 and 254: CPLD Optimization This chapter cont
Page 255 and 256: Implementation Details for Macro Ge
Page 257 and 258: CPLD Optimization • Final results
Page 259 and 260: CPLD Optimization The CPLD fitter m
Page 261 and 262: Design Constraints Chapter 5 This c
Page 263 and 264: Synthesis Options Design Constraint
Page 265 and 266: Design Constraints Figure 5-4 Synth
Page 267 and 268: • Mux Extraction • Mux Style
Page 269 and 270: Design Constraints For FPGA device
Page 271 and 272: XST Constraint File (XCF) Design Co
Page 273 and 274: Design Constraints Timing Constrain
Page 275 and 276: Design Constraints • Add IO Buffe
Page 277 and 278: Design Constraints the components c
Page 279 and 280: HDL Constraints Design Constraints
Page 281 and 282: FPGA Constraints (non-timing) Desig
Page 283 and 284: Design Constraints • Number of Cl
Page 285 and 286: Design Constraints This constraint
Page 287 and 288:
Timing Constraints Design Constrain
Page 289 and 290:
Design Constraints See the “CLOCK
Page 291 and 292:
Design Constraints The following ti
Page 293 and 294:
Design Constraints • TIMEGRP TIME
Page 295 and 296:
Design Constraints See the “INPAD
Page 297 and 298:
Constraint Name clock_buffer bufgdl
Page 299 and 300:
Constraint Name move_last- _stage m
Page 301 and 302:
Constraint Name xor_collapse yes, n
Page 303 and 304:
Constraint Name synthesis/ synopsis
Page 305 and 306:
Design Constraints The following ta
Page 307 and 308:
*Also Supported in XCF format. Impl
Page 309 and 310:
Design Constraints The binary equiv
Page 311 and 312:
Table 5-5 Third Party Constraints N
Page 313 and 314:
Table 5-5 Third Party Constraints N
Page 315 and 316:
Constraints Precedence Design Const
Page 317 and 318:
VHDL Language Support Chapter 6 Thi
Page 319 and 320:
VHDL Language Support 'W' means wea
Page 321 and 322:
VHDL Language Support compiled in t
Page 323 and 324:
Record Types Objects in VHDL MATRIX
Page 325 and 326:
Entity Declaration VHDL Language Su
Page 327 and 328:
VHDL Language Support Example 6-2 g
Page 329 and 330:
VHDL Language Support Example 6-3 4
Page 331 and 332:
egin Y 13), port map (X,Y,C1); C2
Page 333 and 334:
VHDL Language Support Example 6-5 M
Page 335 and 336:
VHDL Language Support Example 6-8 N
Page 337 and 338:
Example 6-10 Combinatorial Process
Page 339 and 340:
VHDL Language Support Example 6-12
Page 341 and 342:
For...Loop Statement VHDL Language
Page 343 and 344:
Sequential Process without a Sensit
Page 345 and 346:
egin if RST = '1' then DO
Page 347 and 348:
Multiple Wait Statements Descriptio
Page 349 and 350:
Functions and Procedures VHDL Langu
Page 351 and 352:
VHDL Language Support Example 6-24
Page 353 and 354:
STANDARD Package VHDL Language Supp
Page 355 and 356:
VHDL Language Support Note Function
Page 357 and 358:
Packages Enumeration Types Integer
Page 359 and 360:
Table 6-4 Objects VHDL Language Sup
Page 361 and 362:
Wait Statement Loop Statement Table
Page 363 and 364:
VHDL Reserved Words The following t
Page 365 and 366:
Verilog Language Support Chapter 7
Page 367 and 368:
Behavioral Verilog Features Verilog
Page 369 and 370:
Verilog Language Support Example 7-
Page 371 and 372:
Table 7-1 Expressions Bitwise Negat
Page 373 and 374:
Modules Verilog Language Support In
Page 375 and 376:
Procedural Assignments Verilog Lang
Page 377 and 378:
Verilog Language Support Casez trea
Page 379 and 380:
While Loops Verilog Language Suppor
Page 381 and 382:
Verilog Language Support Example 7-
Page 383 and 384:
Verilog Language Support The main l
Page 385 and 386:
Verilog Language Support • You ca
Page 387 and 388:
Example 7-9 Function Declaration an
Page 389 and 390:
Blocking Versus Non-Blocking Proced
Page 391 and 392:
Include Files Verilog Language Supp
Page 393 and 394:
Verilog Language Support Each insta
Page 395 and 396:
Parameters Verilog Language Support
Page 397 and 398:
Verilog Language Support • Design
Page 399 and 400:
Verilog Meta Comments Verilog Langu
Page 401 and 402:
Table 7-4 Data Types Registers Vect
Page 403 and 404:
Table 7-8 Design Hierarchy Module d
Page 405 and 406:
Verilog Reserved Keywords Verilog L
Page 407 and 408:
Command Line Mode Introduction Chap
Page 409 and 410:
Command Line Mode • Script File
Page 411 and 412:
Command Line Mode • Second column
Page 413 and 414:
Table 8-4 HDL Options (VHDL and Ver
Page 415 and 416:
Command Line Mode Table 8-6 Target
Page 417 and 418:
Command Line Mode • To get a list
Page 419 and 420:
Elaborate Command Time Command Comm
Page 421 and 422:
♦ smallcntr.vhd Command Line Mode
Page 423 and 424:
Command Line Mode You can improve t
Page 425 and 426:
Command Line Mode Sometimes, XST is
Page 427 and 428:
XST Shell Command Line Mode To use
Page 429 and 430:
Case 2 Command Line Mode Each desig
Page 431 and 432:
Log File Analysis Introduction This
Page 433 and 434:
Quiet Mode Timing Report Log File A
Page 435 and 436:
RAM Style : Auto ROM Extraction : y
Page 437 and 438:
Synthesizing Unit . Related source
Page 439 and 440:
# Counters : 2 # 4-bit up counter :
Page 441 and 442:
Log File Analysis Data Path: sixty_
Page 443 and 444:
CPLD Log File Log File Analysis The
Page 445 and 446:
Analyzing Entity (Architecture ).
Page 447 and 448:
Log File Analysis =================
Page 449 and 450:
XST Naming Conventions This appendi
show all

Xilinx Synthesis Technology User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?