You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Firmware Upgrade Procedure<br />
F1DP216G, F1DP232G<br />
<strong>Belkin</strong> OmniView IP 5216K and 5232K KVM/IP Switch<br />
Please have the following items ready before you start:<br />
IP KVM<br />
USB keyboard and mouse<br />
VGA Monitor<br />
Computer for remote login<br />
Internet Explorer, Mozilla Firefox, Google Chrome<br />
Network connection<br />
Firmware files (downloaded from <strong>Belkin</strong>’s website):<br />
BELKIN_2_16_DIGITAL_UPDATE_V1_1_B618_20120227.bfp<br />
BELKIN_UPDATE_KVMIP_B534_B535_20110828.64b<br />
Instructions:<br />
1. Connect a USB keyboard and mouse to the KVM Switch.<br />
2. Connect a network cable to the LAN port on the KVM.<br />
3. Power up the KVM. Wait until the LEDs stop blinking.<br />
4. After it boots (approx. 45 secs), quickly press the Scroll Lock key twice on the local keyboard to<br />
initiate the OSD on the connected monitor.<br />
5. Press F2 for settings, to get the following screen:<br />
6. Note the DHCP IP address from the OSD.<br />
7. Press the Escape (ESC) on the local keyboard to get out of the OSD.<br />
8. Type in the IP address on a 32-bit IE browser on a computer on the same network as the KVM.<br />
9. If you encounter a website certificate error message (as shown below), just click continue.
<strong>Belkin</strong> OmniView IP 5216K and 5232K KVM/IP Switch<br />
10. At the <strong>Belkin</strong> login screen (see below) from the remote PC, enter the default login info:<br />
username: admin<br />
password: SMBremote.<br />
11. Navigate to the configuration page and upload the .bfp file. The upload process takes<br />
approximately 10 minutes.
<strong>Belkin</strong> OmniView IP 5216K and 5232K KVM/IP Switch<br />
12. When the update is done, the login screen will re-appear.<br />
13. Power-cycle the KVM.<br />
14. After the power-cycle, wait until the LEDs stop blinking.<br />
15. After it boots (approx. 45 secs), quickly press the Scroll Lock key twice on the local keyboard to<br />
initiate the OSD on the connected monitor.<br />
16. Press F2 for settings.<br />
17. Note the DHCP address from the OSD.<br />
18. Press ESC to get out of the OSD.<br />
19. Type in the IP address on any Java-based browser (Firefox, Chrome) on a computer on the same<br />
network as the KVM.<br />
20. Ensure to enable pop-ups and install Java plug-ins at the prompt.<br />
21. If Java is not installed, download and install Java.<br />
22. Once the Java plug-ins are installed, you will see the new login screen (see below):<br />
23. From the <strong>Belkin</strong> login screen from the remote PC, enter the default login info:<br />
username: admin<br />
password: SMBremote.
<strong>Belkin</strong> OmniView IP 5216K and 5232K KVM/IP Switch<br />
24. Go to the configuration page, then click Device Upgrade as shown below:
<strong>Belkin</strong> OmniView IP 5216K and 5232K KVM/IP Switch<br />
25. Select the software with the filename extension .64b.<br />
26. Upload the .64b file. The upload process takes approximately 15 minutes.
<strong>Belkin</strong> OmniView IP 5216K and 5232K KVM/IP Switch<br />
27. When the update is done, the login screen will appear.<br />
28. Power-cycle the KVM to complete the firmware upgrade process.<br />
29. Log in using a Java enabled browser.
Change language