Technical Product Specification for Canoe Pass - Preminary - Intel
Technical Product Specification for Canoe Pass - Preminary - Intel
Technical Product Specification for Canoe Pass - Preminary - Intel
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>Intel</strong> ® Server System P4000CP Power System Options <strong>Intel</strong> ® Server Board S2600CP and Server System P4000CP TPS<br />
13.5.3 Protection Circuits<br />
The PDB shall shut down all the DC/DC converters on the PDB and the power supply (via<br />
PSON) if there is a fault condition on the PDB (OVP or OCP). If the PDB DC/DC converter<br />
latches off due to a protection circuit tripping, an AC cycle OFF <strong>for</strong> 15sec min or a PSON# cycle<br />
HIGH <strong>for</strong> 1sec shall be able to reset the power supply and the PDB.<br />
13.5.3.1 Over-Current Protection (OCP)/240VA Protection<br />
Each DC/DC converter output on PDB has individual OCP protection circuits. The PS+PDB<br />
combo shall shutdown and latch off after an over current condition occurs. This latch shall be<br />
cleared by toggling the PSON # signal or by an AC power interruption. The values are measured<br />
at the PDB harness connectors. The DC/DC converters shall not be damaged from repeated<br />
power cycling in this condition. Also, the +12V output from the power supply is divided on the<br />
PDB into 4 channels and +12V4 is limited to 240VA of power. There are current sensors and<br />
limit circuits to shut down the entire PS+PDB combo if the limit is exceeded. The limits are listed<br />
in below table. -12V and 5VSB is protected under over current or shorted conditions so that no<br />
damage can occur to the power supply. Auto-recovery feature is a requirement on 5VSB rail.<br />
150<br />
Table 146. PDB Over Current Protection Limits/240VA Protection<br />
Output Voltage Min OCP Trip Limits Max OCP Trip Limits Usage Connectors<br />
+3.3V 27A 32A PCIe, Misc P1, P5, P6<br />
+5V 27A 32A PCIe, HDD, Misc P1, P5, P6<br />
+12V1 91A 100A CPU1 + memory Fans,<br />
Misc<br />
P1-P3, P12<br />
+12V2 76A 100A HDD & peripherals P13-P16<br />
+12V3 18A 20A P5-P11<br />
13.5.3.2 Over Voltage Protection (OVP)<br />
Each DC/DC converter output on PDB have individual OVP protection circuits built in and it shall<br />
be locally sensed. The PS+PDB combo shall shutdown and latch off after an over voltage<br />
condition occurs. This latch shall be cleared by toggling the PSON # signal or by an AC power<br />
interruption. Table 98 contains the over voltage limits. The values are measured at the PDB<br />
harness connectors. The voltage shall never exceed the maximum levels when measured at the<br />
power pins of the output harness connector during any single point of fail. The voltage shall<br />
never trip any lower than the minimum levels when measured at the power pins of the PDB<br />
connector.<br />
Table 147. Over Voltage Protection (OVP) Limits<br />
Output voltage OVP min (v) OVP max (v)<br />
+3.3V 3.9 4.8<br />
+5V 5.7 6.5<br />
-12V -13.3 -15.5<br />
+5VSB 5.7 6.5<br />
<strong>Intel</strong> Confidential Revision 0.8<br />
<strong>Intel</strong> order number G26942-003