Technical Product Specification for Canoe Pass - Preminary - Intel

More documents

Recommendations

Info

Intel ® Server System P4000CP Power System Options Intel ® Server Board S2600CP and Server System P4000CP TPS 136 Converter output Tolerance Min Nom Max Units + 3.3VDC -5%/+5% +3.14 +3.30 +3.46 VDC + 5VDC -5%/+5% +4.75 +5.00 +5.25 VDC - 12VDC - 5%/+9% -13.08 -12.00 -11.40 VDC 5Vstby -5%/+5% +4.75 +5.00 +5.25 VDC 13.4.2.10 DC/DC Converters Dynamic Loading The output voltages remains within limits specified in table above for the step loading and capacitive loading specified in the table below. The load transient repetition rate is only a test specification. The step load may occur anywhere within the MIN load to the MAX load shown in Tables 116 and 117. Table 115. Transient Load Requirements Output Max Step Load Size Max Load Slew Rate Test capacitive Load + 3.3VDC 5A 0.25 A/s 250 F + 5VDC 5A 0.25 A/s 400 F +5Vsb 0.5A 0.25A/s 20 F 13.4.2.11 DC/DC Converter Capacitive Loading The DC/DC converters are stable and meet all requirements with the following capacitive loading ranges. Minimum capacitive loading applies to static load only. Table 116. Capacitive Loading Conditions Converter output Min Max Units +3.3VDC 250 6800 F +5VDC 400 4700 F -12VDC 1 350 F 5Vstby 20 350 F 13.4.2.12 DC/DC Converters Closed Loop stability Each DC/DC converter is unconditionally stable under all line/load/transient load conditions including capacitive load ranges specified in Section 13.4.2.11. A minimum of: 45 degrees phase margin and -10dB-gain margin is required. The PDB provides proof of the unit’s closed-loop stability with local sensing through the submission of Bode plots. Closed-loop stability must be ensured at the maximum and minimum loads as applicable. 13.4.2.13 Common Mode Noise The Common Mode noise on any output does not exceed 350mV pk-pk over the frequency band of 10Hz to 20MHz. The measurement shall be made across a 100Ω resistor between each of DC outputs, including ground, at the DC power connector and chassis ground (power subsystem enclosure). The test set-up shall use a FET probe such as Tektronix model P6046 or equivalent. Intel Confidential Revision 0.8 Intel order number G26942-003
Intel ® Server Board S2600CP and Server System P4000CP TPS Intel ® Server System P4000CP Power System Options 13.4.2.14 Ripple/Noise The maximum allowed ripple/noise output of each DC/DC Converter is defined in the table below. This is measured over a bandwidth of 0Hz to 20MHz at the PDB output connectors. A 10F tantalum capacitor in parallel with a 0.1F ceramic capacitor are placed at the point of measurement. The test set-up shall be as shown below. Table 117. Ripple and Noise +3.3V +5V -12V +5VSB 50mVp-p 50mVp-p 120mVp-p 50mVp-p V OUT AC HOT POWER SUPPLY V AC NEUTRAL RETURN AC GROUND GENERAL NOTES: 1. LOAD THE OUTPUT WITH ITS MINIMUM LOAD CURRENT. 2. CONNECT THE PROBES AS SHOWN. 3. REPEAT THE MEASUREMENTS WITH THE MAXIMUM LOAD ON THE OUTPUT. 10uF .1uF Revision 0.8 Intel Confidential Intel order number G26942-003 LOAD LOAD MUST BE ISOLATED FROM THE GROUND OF THE POWER SUPPLY SCOPE SCOPE NOTE: USE A TEKTRONIX 7834 OSCILLOSCOPE WITH 7A13 AND DIFFERENTIAL PROBE P6055 OR EQUIVALENT. Note: When performing this test, the probe clips and capacitors should be located close to the load. Figure 52. Differential Noise test setup 13.4.2.15 Timing Requirements Below are timing requirements for the power on/off of the PDB DC/DC converters. The +3.3V, +5V and +12V output voltages should start to rise approximately at the same time. All outputs must rise monotonically. Table 118. Output Voltage Timing Description Min Max Units Output voltage rise time for each main output; 3.3V, 5V, and - 12V. 5.0 70 msec Output voltage rise time for the 5Vstby 1.0 25 msec The main DC/DC converters (3.3V, 5V, -12V) shall be in regulation limits within this time after the 12V input has reached 11.4V. The main DC/DC converters (3.3V, 5V, -12V) must power off within this time after the 12V input has dropped below 11.4V. The 5Vstby converter shall be in regulation limits within this time after the 12Vstby has reach 11.4V. The 5Vstby converter must power off within this time after the 12Vstby input has dropped below 11.4V. 50 msec 100 msec 10 msec 100 msec 137
Page 1 and 2:
Intel ® Server Board S2600CP Intel
Page 3 and 4:
Intel ® Server Board S2600CP and S
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102: Intel ® Server Board S2600CP and S
Page 151: Intel ® Server Board S2600CP and S
Page 173 and 174: Intel® Server System P4000CP TPS D
Page 183 and 184: Intel® Server System P4000CP TPS A
Page 201 and 202: Intel® Server System P4000CP TPS A
Page 203 and 204:
Intel® Server System P4000CP TPS A
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Error! No text of specified style i
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
® Intel ® Server Board S2600CP an
Page 219 and 220:
® Intel ® Server Board S2600CP an
show all

Technical Product Specification for Canoe Pass - Preminary - Intel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?