Technical Product Specification for Canoe Pass - Preminary - Intel

More documents

Recommendations

Info

Intel ® Server System P4000CP Power System Options Intel ® Server Board S2600CP and Server System P4000CP TPS supply recovers and meets all turn on requirements. The power supply meets the AC dropout requirement over rated AC voltages and frequencies. A dropout of the AC line for any duration does not cause damage to the power supply. 108 Table 61. AC Line Holdup time Loading Holdup time 75% 12msec 13.2.3.5 AC Line Fuse The power supply has one line fused in the single line fuse on the line (Hot) wire of the AC input. The line fusing is acceptable for all safety agency requirements. The input fuse is a slow blow type. AC inrush current does not cause the AC line fuse to blow under any conditions. All protection circuits in the power supply do not cause the AC fuse to blow unless a component in the power supply has failed. This includes DC output load short conditions 13.2.3.6 AC Line Leakage Current The maximum leakage current to ground for each power supply is 3.5mA when tested at 240VAC. 13.2.3.7 AC Line Transient Specification AC line transient conditions are defined as “sag” and “surge” conditions. “Sag” conditions are also commonly referred to as “brownout”, these conditions is defined as the AC line voltage dropping below nominal voltage conditions. “Surge” is defined to refer to conditions when the AC line voltage rises above nominal voltage. The power supply meets the requirements under the following AC line sag and surge conditions. Table 62. AC Line Sag Transient Performance AC Line Sag (10sec interval between each sagging) Duration Sag Operating AC Voltage Line Frequency Performance Criteria 0 to 1/2 AC cycle 95% Nominal AC Voltage ranges 50/60Hz No loss of function or performance > 1 AC cycle >30 % Nominal AC Voltage ranges 50/60Hz Loss of function acceptable, self recoverable Table 63. AC Line Surge Transient Performance AC Line Surge Duration Surge Operating AC Voltage Line Frequency Performance Criteria Continuous 10% Nominal AC Voltages 50/60Hz No loss of function or performance 0 to ½ AC cycle 30% Mid-point of nominal AC Voltages 13.2.3.8 Power Recovery 50/60Hz No loss of function or performance The power supply recovers automatically after an AC power failure. AC power failure is defined to be any loss of AC power that exceeds the dropout criteria. Intel Confidential Revision 0.8 Intel order number G26942-003
Intel ® Server Board S2600CP and Server System P4000CP TPS Intel ® Server System P4000CP Power System Options 13.2.4 Efficency The following table provides the required minimum efficiency level at various loading conditions. These are provided at three different load levels; 100%, 50% and 20%. Output shall be load according to the proportional loading method defined by 80 Plus in Generalized Internal Power Supply Efficiency Testing Protocol Rev 6.4.3. This is posted at http://efficientpowersupplies.epri.com/methods.asp. Table 64. Silver Efficiency Requirement Loading 100% of maximum 50% of maximum 20% of maximum Minimum Efficiency 85% 88% 85% The power supply passes with enough margins to make sure in production all power supplies meet these efficiency requirements. 13.2.4.1 Standy Efficiency When in standby mode; the power supply draws less than 1W AC power with 100mA of 5Vstandby load. This is tested at 115VAC/60Hz and 230VAC/50Hz. 13.2.5 DC Output Specification 13.2.5.1 Output Power/Currents The following tables define the minimum power and current ratings. The power supply meets both static and dynamic voltage regulation requirements for all conditions. Table 65. Over Voltage Protection Limits Parameter Min Max. Peak Unit 3.3V 0.5 18.0 A 5V 0.3 15.0 A 12V1 0.7 24.0 28.0 A 12V2 0.7 24.0 28.0 A 12V3 1.5 18.0 3.3V 0.5 18.0 A 12V 0.0 0.5 A 5Vstby 0.0 3.0 3.5 A Notes: 1. Max combined power for all output shall not exceed 550W. 2. Peak combined power for all outputs shall not exceed 630W for 20 seconds. 3. Max combined power of 12V1, 12V2 and 12V3 shall not exceed 530W. 4. Max combined power on 3.3V and 5V shall not exceed 120W. 13.2.5.2 Cross Loading The power supply maintains voltage regulation limit when operated over the following cross loading conditions. Revision 0.8 Intel Confidential Intel order number G26942-003 109
Page 1 and 2:
Intel ® Server Board S2600CP Intel
Page 3 and 4:
Intel ® Server Board S2600CP and S
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74: Intel ® Server Board S2600CP and S
Page 123: Intel ® Server Board S2600CP and S
Page 173 and 174: Intel® Server System P4000CP TPS D
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Intel® Server System P4000CP TPS A
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Error! No text of specified style i
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
® Intel ® Server Board S2600CP an
Page 219 and 220:
® Intel ® Server Board S2600CP an
show all

Technical Product Specification for Canoe Pass - Preminary - Intel

Create successful ePaper yourself

Delete template?

Save as template?