TRITON Extreme Operation Guide - Platinum Audiolab
TRITON Extreme Operation Guide - Platinum Audiolab
TRITON Extreme Operation Guide - Platinum Audiolab
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
72<br />
If the edit cell is located at “Range Start” or “Range<br />
End,” this region will play back.<br />
When you finish making settings, press the<br />
SEQUENCER [START/STOP] key to stop playback of<br />
the audio CD.<br />
7 Verify the region that will be ripped.<br />
Select either “Region Start” or “Region End” (the display<br />
will be highlighted), and press the SEQUENCER<br />
[START/STOP] key. The CD will play from “Range<br />
Start” to “Range End” and then stop.<br />
If you want to adjust the location, use the VALUE<br />
controllers to modify the “Range Start” or “Range<br />
End” settings, or move the cursor to a parameter<br />
other than “Range Start” and “Range End” and<br />
repeat step 5 to make the setting once again.<br />
If you want to move the track playback start location<br />
to the beginning of the track, press the [LOCATE] key.<br />
8 When you have finished setting “Range Start” and<br />
“Range End,” select the page menu command “Destination.”<br />
A dialog box will appear.<br />
Specify the destination to which the ripped sample will<br />
be written.<br />
Select RAM if you want to rip the sample into sample<br />
memory (RAM). In this case, you can also set Sample<br />
No. (L), (R) to specify the sample number that will be<br />
written. Normally you can leave this unchanged.<br />
Select MEDIA if you want to rip the sample to media.<br />
Use drive select to select the drive, and use the Open<br />
and Up buttons to select the directory in which the<br />
data will be saved. Also specify a name for the WAVE<br />
file that will be saved.<br />
9 Press the OK button to execute ripping, or press the<br />
Cancel button to cancel without executing.<br />
When you press the OK button, the “Obey Copyright<br />
Rules” dialog box will appear.<br />
Carefully read “About copyright” (☞QS p.iii), and if<br />
you consent to the terms, press the OK button to<br />
begin ripping. If you do not consent to the terms,<br />
press the Cancel button to cancel the operation.<br />
Reading the analog audio output of an audio CD into<br />
a sample<br />
Here’s how analog audio data from an audio CD track can<br />
be loaded into a sample.<br />
In the same way as when inputting the output of your CD<br />
player to the <strong>TRITON</strong> <strong>Extreme</strong>’s AUDIO IN 1, 2 jacks, use<br />
audio cables to connect the audio output of the CD-ROM<br />
or CD-R/RW drive connected to the USB A connector to<br />
the <strong>TRITON</strong> <strong>Extreme</strong>’s AUDIO INPUT 1, 2.<br />
You can use the <strong>TRITON</strong> <strong>Extreme</strong>’s SEQUENCER<br />
[START/STOP] key etc. to control operations such as<br />
playback and stop on your CD-ROM or CD-R/RW drive.<br />
1 Use audio cables to connect the audio outputs of your<br />
CD-ROM or CD-R/RW drive (connected to the USB A<br />
connector) to AUDIO INPUT 1, 2 of the <strong>TRITON</strong><br />
<strong>Extreme</strong>.<br />
2 Insert an audio CD.<br />
3 Access the Sampling mode P5: Audio CD, Ripping<br />
page.<br />
4 Use “Media” (media select) to select the drive that<br />
contains the audio CD, and use “Track” to select the<br />
track that you want to read.<br />
Raise the “Volume.”<br />
Some USB A connector CD-ROM or CD-R/RW<br />
drives cannot be controlled in this way, so this setting<br />
may not affect the volume.<br />
5 In the P0: Recording, Input/Setup page, make Input<br />
settings as follows.<br />
“Input” Analog<br />
Input1 “Level” 127, “Pan” L000, “BUS Select” L/R<br />
Input2 “Level” 127, “Pan” R127, “BUS Select” L/R<br />
6 Specify the recording method in Recording Setup.<br />
“Source BUS” L/R<br />
“Trigger” Sampling START SW<br />
Sampling will start when you press the SAMPLING<br />
[START/STOP] key.<br />
“Resampling” Manual<br />
7 In REC Sampling Setup, make settings for the sample<br />
that will be recorded.<br />
“Save to” RAM: if you want to write the sample into<br />
sample memory (RAM)<br />
“Save to” MEDIA: if you want to write the sample to<br />
media<br />
“Sample Mode” Stereo<br />
“Sample Time” maximum