TRITON Extreme Operation Guide - Platinum Audiolab

More documents

Recommendations

Info

12 About polyphony Tone generators and oscillators Each oscillator in the TRITON Extreme is sounded by one of two Tone Generators. Each tone generator is connected to the various PCM memories as shown in the diagram below. Tone Generator 1 • ROM: Internal PCM ROM (32 Mbytes) • RAM: User sample memory (16 Mbytes, expandable to a maximum of 96 Mbytes) Tone Generator 2 • Piano: • New1: • New2: • Best: • OrchS: • OrchB: • Vint: • Synth: Internal PCM ROM (128 Mbytes) PCM memory PCM memory Piano (Internal PCM ROM) 16 Mbytes ROM (Internal PCM ROM) 32 Mbytes New1 ( " ) 16 Mbytes RAM (User sample memory) 96 Mbytes* * = Expandable to a maximum. Factory settings is 16 Mbytes New2 ( " ) 16 Mbytes Best ( " ) 16 Mbytes OrchS ( " ) 16 Mbytes OrchB ( " ) 16 Mbytes Vint ( " ) 16 Mbytes Synth ( " ) 16 Mbytes Total 128 Mbytes Tone Generator 1 Tone Generator 2 Maximum 60 oscillators Maximum 60 oscillators Total maximum 120 oscillators Each tone generator is able to simultaneously sound up to 60 oscillators (i.e., to play the PCM data connected to that tone generator). Together, the two tone generators are able to sound up to 120 oscillators. For example up to 60 oscillators can use the ROM, and up to 60 oscillators can use the Piano, making a total of 120 oscillators. However, you can’t play 61 or more oscillators from the ROM alone. Number of voices in each mode The maximum number of voices that can be played simultaneously will depend on the oscillator mode of the program. • For a Single/Drum-mode program, 1 oscillator = 1 voice • For a Double-mode program, 2 oscillators = 1 voice Program mode Single/Drums (“Oscillator Mode”) Normally, 60 voices can be used. However a maximum of 120 voices will be available if, for example, ROM or RAM is used for the High MS, and Piano–Synth is used for the Low MS, and you use velocity switching to play the two tone generators. Double (“Oscillator Mode”) Normally, 30 voices can be used. However if OSC1 is sounded by one tone generator and OSC2 is sounded by the other tone generator (e.g., OSC1=ROM, OSC2=Piano–Synth), a maximum of 60 voices can be used. If OSC1 and OSC2 use one tone generator (e.g., OSC1=ROM, OSC2=ROM), then a maximum of 30 voices can be used. This can also be increased by velocity switch and velocity zone settings. Combination, Sequencer, and Song Play modes Depending on the oscillator mode of the programs you are using, the maximum number will vary between 60 voices and 120 voices. (Example) For single-mode programs that use ROM or RAM, a total maximum of 60 voices For single-mode programs that use Piano–Synth, a total maximum of 60 voices Total 120 voices For double-mode programs that use ROM or RAM, a total maximum of 30 voices For double-mode programs that use Piano–Synth, a total maximum of 30 voices Total 60 voices Sampling mode Tone generator 1 is always used in Sampling mode. Mono samples/multisamples 60 voices. Stereo samples/multisamples 30 voices.
Basic operation 1. Selecting modes In order to use a particular function on the TRITON Extreme, you must first select the appropriate mode. Press one of the front panel mode keys ([COMBI] key – [MEDIA] key) to enter the corresponding mode. [COMBI] key: Combination mode [PROG] key: Program mode [SEQ] key: Sequencer mode [SAMPLING] key: Sampling mode [S.PLAY] key: Song Play mode [GLOBAL] key: Global mode [MEDIA] key: Media mode 2. Selecting pages Each mode has a large number of parameters, which are organized into pages. These are further subdivided by tabs into up to eight tab pages. 1 Make sure that the desired mode is selected. To select a mode, press the appropriate mode key ([COMBI] key – [MEDIA] key). Here we will use Program mode as an example for our explanation. Press the [PROG] key. 2 Press the [MENU] key. The page jump menu will appear. COMBI SEQ S.PLAY MEDIA PROG SAMPLING GLOBAL COMPARE In Media mode there is only one page, so the page jump menu will not appear. 3 In the LCD screen, press the desired page. You will jump to the selected page, and it will appear in the display. As an example here, press P1: Edit-Basic. • As a reminder, the page that was selected before you pressed the [MENU] key will have its top right corner bent over. • You can also jump to the corresponding page by pressing a numeric key [0]–[9]. (P0–P9 correspond to numeric keys [0]–[9].) • By holding down the [MENU] key and pressing a numeric key [0]–[9], you can jump directly to the corresponding page without displaying the page jump menu. When you press the [EXIT] key, you will return to P0 from any page. 4 Press one of the tabs located at the bottom of the page. As an example here, press the OSC Basic tab which is the second from the left. • Some pages have no tabs. 5 To move to a page with a different ‘P’ number, press the [MENU] key and continue from step 2 of this procedure. 3. Setting a parameter The parameter value in the edit cell can be set by using the front panel VALUE controllers ([VALUE] slider, [ ][ ] keys, [VALUE] dial, numeric keys [0]–[9], [–] key, [ENTER] key, and [./10’s HOLD] key). As necessary, you can also use the [BANK] keys and the [COMPARE] key. For some parameters, the value can be set by pressing a popup button to display the popup menu and then selecting a parameter value, or by holding down the [ENTER] key and playing a note on the keyboard to input a note number or velocity value. 13 Introduction Program Combination Sequencer Sampling Song Play Global Effect Media, etc Preset Other
Page 1 and 2: E 2
Page 3 and 4: Table of Contents About this manual
Page 5 and 6: Main features The TRITON Extreme is
Page 7 and 8: Front and rear panel Front panel 1
Page 9 and 10: Each time you press the [G] key whe
Page 11 and 12: Use an optical cable to connect thi
Page 13 and 14: f: Check box Each time you press a
Page 15: Sequencer mode • Use the 16-track
Page 19 and 20: Connections Connections must be mad
Page 21 and 22: 6. Inserting and removing CF card s
Page 23 and 24: Program structure Playing and editi
Page 25 and 26: 4 When you are satisfied with the s
Page 27 and 28: Note Number Varying amounts of an e
Page 29 and 30: 3 Adjust the “Lvl” (Level) for
Page 31 and 32: Filter settings P3: Edit-Filter The
Page 33 and 34: Amp1 Mod. page Keyboard Track This
Page 35 and 36: Playing and editing combinations Co
Page 37 and 38: Easy arpeggiator editing Arpeggio P
Page 39 and 40: Settings for status, MIDI channel,
Page 41 and 42: You can also enter these values by
Page 43 and 44: Producing songs (Sequencer mode) TR
Page 45 and 46: Sequencer mode page structure Page
Page 47 and 48: Recording methods This section desc
Page 49 and 50: When simultaneously recording multi
Page 51 and 52: Using “Put Effect Setting to Trac
Page 53 and 54: 9 Press the OK button. Now when you
Page 55 and 56: Decide on the number of measures, i
Page 57 and 58: Creating and playing a Cue List A c
Page 59 and 60: Creating and recording RPPR (Realti
Page 61 and 62: Set “Gate” and “Velocity” t
Page 63 and 64: When using the “Copy From Program
Page 65 and 66: Features of sampling on the TRITON
Page 67 and 68:
Samples and Multisamples Samples Th
Page 69 and 70:
4 For Input1 and Input2, set “BUS
Page 71 and 72:
In Program, Combination, and Sequen
Page 73 and 74:
Creating multisample indexes and sa
Page 75 and 76:
7 In the P8: Insert Effect, Insert
Page 77 and 78:
8 Adjust the recording level. Press
Page 79 and 80:
4 Choose “REC Audio Input.” 5 M
Page 81 and 82:
Sample (waveform data) editing Edit
Page 83 and 84:
5 Press the OK button. The sample w
Page 85 and 86:
4 Connect your guitar to the rear p
Page 87 and 88:
ight of the display) below +0.0 to
Page 89 and 90:
SMF (Standard MIDI File) playback I
Page 91 and 92:
Playback using the Jukebox function
Page 93 and 94:
Settings for the entire TRITON Extr
Page 95 and 96:
pitch change speed, volume, the pan
Page 97 and 98:
6 Use “High Drumsample Bank,”
Page 99 and 100:
4 Adjust the settings of the variou
Page 101 and 102:
Combination D062: Old Vox Organ Alt
Page 103 and 104:
• Tone: At each step, a chord con
Page 105 and 106:
8 Input the open hi-hat (Tone03). S
Page 107 and 108:
Effect and Valve Force settings The
Page 109 and 110:
Master effects The input levels to
Page 111 and 112:
AUDIO INPUT effect settings In Prog
Page 113 and 114:
Valve Force settings Valve Force is
Page 115 and 116:
If you want to route the sound thro
Page 117 and 118:
Loading and saving data, creating a
Page 119 and 120:
Assigning a name (Rename) You can m
Page 121 and 122:
Saving on media Media, Save For det
Page 123 and 124:
Using the TRITON Extreme as a data
Page 125 and 126:
Loading data Media, Load The types
Page 127 and 128:
Loading data by individual item or
Page 129 and 130:
In “Drive,” select your CD-R/RW
Page 131 and 132:
Restoring the factory settings The
Page 133 and 134:
Setting the function of [SW1] and [
Page 135 and 136:
Troubleshooting If you experience p
Page 137 and 138:
Program, Combination Settings for o
Page 139 and 140:
MIDI The TRITON Extreme does not re
Page 141 and 142:
Media that can be used with the TRI
Page 143 and 144:
User interface TouchView graphical
Page 145 and 146:
Index Numerics 10’s Hold 4, 13, 2
Page 147 and 148:
T Tab 9, 13 Tap tempo 7, 74, 90, 13
show all

TRITON Extreme Operation Guide - Platinum Audiolab

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?