TRITON Extreme Operation Guide - Platinum Audiolab

More documents

Recommendations

Info

136 → In the case of a CD-R, it may be possible to make the disc be recognized by executing the page menu command “Convert to ISO9660 Format” (Media, Utility page) to convert the disc to ISO9660 format. However depending on the state in which the disc was saved, it may be converted into ISO9660 level 3 format, and may still not be recognized. ☞PG p.330 Can’t write audio tracks Additional writing is not possible on a CD-R/RW disc that has been finalized. Can’t play back the disc on an audio CD player Did you finalize the disc? → If you want to finalize the disc after writing additional data, check the “Execute finalize too” check box when executing the page menu command “Write to CD” (Media, Make Audio CD), so that the disc will be finalized. ☞p.124, PG p.196 → If you only want to finalize the disc, select the page menu command “Finalize Audio CD” (Media, Make Audio CD), and press the OK button to finalize the disc. ☞PG p.196 Are you using CD-R media? → Since some CD players are unable to play CD-RW media, we recommend that you use CD-R media. Have you tried using a different type of media? → Some CD-R/RW media cannot be played by some CD players. You may be able to play back successfully by using a different type (brand) of CD-R/RW media. WAVE files Playback level of the WAVE file is too high Set “WAVE File Play Level” to Normal. You should usually set “WAVE file Play Level” at Normal, and set it to High (+12 dB) only if the S/P DIF output is too low. With the High (+12 dB) setting, the output from AUDIO OUTPUT L (MONO), R, and HEADPHONES will be louder. ☞PG p.158 WAVE file playback level is louder/softer than the RAM samples Adjust the “WAVE File Play Level.” You should usually set “WAVE File Play Level” to Normal, and use the “High (+12 dB)” setting only if the WAVE file playback volume is lower than the playback of the RAM samples. You should also use the “High (+12 dB)” setting if the S/P DIF output is not loud enough. Can’t preview Is the WAVE file format supported? → Select a WAVE file of a supported format. ☞PG p.176, 195, 315 Other Saved files or sampled WAVE files have an incorrect date/time. → Use the page menu command “Set Date/Time” (Media, Utility page) to set the current date and time. ☞p.120 Included CD-ROM Can’t install the driver Is the USB cable connected correctly? Is the CD-ROM inserted in your CD drive? → Make sure that the CD-ROM is inserted correctly. Could the lens of your CD drive be dirty? → Use a commercially-available lens cleaner to clean the lens. Are you attempting to install from a network CD drive? → This software cannot be installed from a network-connected CD drive. Are you able to use USB? → If you are using Windows XP, go to [Control Panel] → [System], and select the [Hardware] tab. In [Device Manager], check the settings for Universal Serial Bus Controller and USB Root Hub. Has the TRITON Extreme been detected as an unknown device? → If you are using Windows XP, go to [Control Panel] → [System], select the [Hardware] tab, and check [Device Manager]. If the TRITON Extreme has not been detected correctly, it will be displayed in “Other devices” or “Unknown devices.” Reconnect the USB cable; if the TRITON Extreme is again displayed as an “Unknown device,” the computer has failed to detect it correctly. Delete the “Unknown device” entry, and reinstall the driver. ☞PG p.326 Your software does not respond to the TRITON Extreme Is the USB cable connected correctly? Did you install the driver? Has your computer detected the connected TRITON Extreme? → If you are using Windows XP, go to Control Panel → “Sounds and Audio Devices Properties” and click the Hardware tab. If you are using Mac OS X, go to Macintosh HD → Application folder → Utility folder → “Audio MIDI Settings,” select the “MIDI Devices” tab, and check that the TRITON Extreme has been detected. Some computers may not recognize the microKON- TROL because of their hardware configuration. Check the TRITON Extreme’s assignments and USB- MIDI port settings. The connected device or software may not support the messages you are transmitting. Refer to the owner’s manual of the connected device or software to verify that it responds to the messages you are transmitting.
Media that can be used with the TRITON Extreme Types of media that can used with the TRITON Extreme (as of July 2003) Media inserted in the TRITON Extreme’s CF card slot • CF: CompactFlash (Type I, Type II) Power supply voltage 5V only is supported; 16 Mbyte– 1 Gbyte • MD: Microdrive Power supply voltage 5V only is supported; 1 Gbyte External USB storage media • HD: hard disk • RM: removable disk (Magneto-Optical) MS-DOS format FAT16 and FAT32 are supported for HD and RM. Capacity recognized: FAT32: up to 2 Tbytes = 2,000 Gbytes FAT16: up to 4 Gbytes • CDR (CD-R/RW) UDF format is supported. UDF format CD-R/RW can be written and read. (Packet writing support ☞PG p.330) CD-DA (audio data) can be recorded/played, and ISO9660 (level 1) format can be loaded. Requirements for external USB storage media that can be recognized by the TRITON Extreme are described on PG p.325. For details on connecting the USB A/B connectors, refer to PG p.325. ● : possible ✕ : not possible - : not applicable ▲ : partial support *1: Writing may not be possible for some media *2: Only loading is possible USB A: CD-DA (audio CD) can be ripped in Sampling mode. Operations that the TRITON Extreme can perform on media • Save/Load (Media mode) Internal memory and sample memory (RAM) data can be saved/loaded. For details on the files that can be saved or loaded, refer to the table on PG p.175. Loading or saving a divided file is supported for media connected to the USB A connector. • Sampling/resampling (Program, Combination, Sequencer, Sampling modes) If “Save to” = MEDIA, sampled/resampled Wave files will be written to media. • Wave file playback (Sequencer, Media modes) Wave files can be played. • Wave file editing (Media mode) Wave files can be edited. • SMF direct playback (Song Play mode) SMF can be played back directly from media. • Audio CD creation (Media mode) A CD-R/RW drive can be used to create an audio CD from Wave files. Writing may not be possible depending on the media on which the Wave files are saved. • Data transfer to/from a computer (Media mode) Data from CompactFlash media inserted in the TRI- TON Extreme’s CF card slot can be saved to the computer, or data from the computer can be loaded to the CompactFlash media. • Convert to ISO9660 Format (Media mode) UDF format CD-R media can be converted to ISO9660 format. If you have any questions regarding the media that can be used, please contact your local Korg distributor. You may also check the Korg website (http:// www.korg.com/downloads). Media Built-in: MD Built-in: CF USB A: HD USB A: RM USB A: CD-R/RW USB A: CD-R/RW Function (Micro drive) (Flash Memory) (Hard Disk) (Removable Media) (Packet Write) (ISO9660) Save/Load ● ● ● ● ● ▲ * 2 Sampling/Resampling ● ▲ * 1 ✕ ✕ ✕ - WAVE File Play ● ● ✕ ✕ ✕ ✕ Edit Wave ● ● ● ✕ ✕ ✕ SMF direct play ● ● ● ● ● ● Make Audio CD ● (from) ● (from) ● (from) ● (from) ● (to) ● (from) USB Storage ● ● ✕ ✕ ✕ ✕ Convert to ISO9660 Format - - - - ● (to) - 137 Program Combination Sequencer Sampling Song Play Global Effect Media, etc Preset Other Appendices
Page 1 and 2:
E 2
Page 3 and 4:
Table of Contents About this manual
Page 5 and 6:
Main features The TRITON Extreme is
Page 7 and 8:
Front and rear panel Front panel 1
Page 9 and 10:
Each time you press the [G] key whe
Page 11 and 12:
Use an optical cable to connect thi
Page 13 and 14:
f: Check box Each time you press a
Page 15 and 16:
Sequencer mode • Use the 16-track
Page 17 and 18:
Basic operation 1. Selecting modes
Page 19 and 20:
Connections Connections must be mad
Page 21 and 22:
6. Inserting and removing CF card s
Page 23 and 24:
Program structure Playing and editi
Page 25 and 26:
4 When you are satisfied with the s
Page 27 and 28:
Note Number Varying amounts of an e
Page 29 and 30:
3 Adjust the “Lvl” (Level) for
Page 31 and 32:
Filter settings P3: Edit-Filter The
Page 33 and 34:
Amp1 Mod. page Keyboard Track This
Page 35 and 36:
Playing and editing combinations Co
Page 37 and 38:
Easy arpeggiator editing Arpeggio P
Page 39 and 40:
Settings for status, MIDI channel,
Page 41 and 42:
You can also enter these values by
Page 43 and 44:
Producing songs (Sequencer mode) TR
Page 45 and 46:
Sequencer mode page structure Page
Page 47 and 48:
Recording methods This section desc
Page 49 and 50:
When simultaneously recording multi
Page 51 and 52:
Using “Put Effect Setting to Trac
Page 53 and 54:
9 Press the OK button. Now when you
Page 55 and 56:
Decide on the number of measures, i
Page 57 and 58:
Creating and playing a Cue List A c
Page 59 and 60:
Creating and recording RPPR (Realti
Page 61 and 62:
Set “Gate” and “Velocity” t
Page 63 and 64:
When using the “Copy From Program
Page 65 and 66:
Features of sampling on the TRITON
Page 67 and 68:
Samples and Multisamples Samples Th
Page 69 and 70:
4 For Input1 and Input2, set “BUS
Page 71 and 72:
In Program, Combination, and Sequen
Page 73 and 74:
Creating multisample indexes and sa
Page 75 and 76:
7 In the P8: Insert Effect, Insert
Page 77 and 78:
8 Adjust the recording level. Press
Page 79 and 80:
4 Choose “REC Audio Input.” 5 M
Page 81 and 82:
Sample (waveform data) editing Edit
Page 83 and 84:
5 Press the OK button. The sample w
Page 85 and 86:
4 Connect your guitar to the rear p
Page 87 and 88:
ight of the display) below +0.0 to
Page 89 and 90: SMF (Standard MIDI File) playback I
Page 91 and 92: Playback using the Jukebox function
Page 93 and 94: Settings for the entire TRITON Extr
Page 95 and 96: pitch change speed, volume, the pan
Page 97 and 98: 6 Use “High Drumsample Bank,”
Page 99 and 100: 4 Adjust the settings of the variou
Page 101 and 102: Combination D062: Old Vox Organ Alt
Page 103 and 104: • Tone: At each step, a chord con
Page 105 and 106: 8 Input the open hi-hat (Tone03). S
Page 107 and 108: Effect and Valve Force settings The
Page 109 and 110: Master effects The input levels to
Page 111 and 112: AUDIO INPUT effect settings In Prog
Page 113 and 114: Valve Force settings Valve Force is
Page 115 and 116: If you want to route the sound thro
Page 117 and 118: Loading and saving data, creating a
Page 119 and 120: Assigning a name (Rename) You can m
Page 121 and 122: Saving on media Media, Save For det
Page 123 and 124: Using the TRITON Extreme as a data
Page 125 and 126: Loading data Media, Load The types
Page 127 and 128: Loading data by individual item or
Page 129 and 130: In “Drive,” select your CD-R/RW
Page 131 and 132: Restoring the factory settings The
Page 133 and 134: Setting the function of [SW1] and [
Page 135 and 136: Troubleshooting If you experience p
Page 137 and 138: Program, Combination Settings for o
Page 139: MIDI The TRITON Extreme does not re
Page 143 and 144: User interface TouchView graphical
Page 145 and 146: Index Numerics 10’s Hold 4, 13, 2
Page 147 and 148: T Tab 9, 13 Tap tempo 7, 74, 90, 13
show all

TRITON Extreme Operation Guide - Platinum Audiolab

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?