TRITON Extreme Operation Guide - Platinum Audiolab
TRITON Extreme Operation Guide - Platinum Audiolab
TRITON Extreme Operation Guide - Platinum Audiolab
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Troubleshooting<br />
If you experience problems, refer to the relevant item and<br />
take the appropriate measures.<br />
Power supply<br />
Power does not turn on<br />
Is the power cable connected to an outlet? ☞p.16<br />
Is the [POWER] switch turned on?<br />
→ Turn on the rear panel [POWER] switch. ☞p.18<br />
LCD screen<br />
The power is turned on, but nothing is shown in the LCD<br />
screen.<br />
The <strong>TRITON</strong> <strong>Extreme</strong> functions normally when you play the<br />
keyboard or perform other operations.<br />
Use the rear panel [Contrast adjustment] knob to<br />
adjust the contrast of the LCD screen. ☞p.7<br />
The power is turned on, but the LCD screen does not display<br />
normally, or an error message is displayed. There is no<br />
sound when you play the keyboard, and the <strong>TRITON</strong><br />
<strong>Extreme</strong> does not function normally.<br />
This type of problem may occur if a data writing<br />
operation to internal memory was not completed<br />
correctly, for example if the power of the <strong>TRITON</strong><br />
<strong>Extreme</strong> was turned off while a program or other data<br />
was being written. If this occurs, use the following<br />
procedure to initialize the <strong>TRITON</strong> <strong>Extreme</strong>’s internal<br />
memory.<br />
1 Turn off the power.<br />
2 Hold down the [MENU] key and the [9] key, and turn<br />
on the power.<br />
The <strong>TRITON</strong> <strong>Extreme</strong> will be initialized, and data will<br />
be written into internal memory. While the data is<br />
being written, the LCD screen will indicate “Now writing<br />
into internal memory.”<br />
After initialization, all user data will be empty, and you<br />
will need to re-load the preload data. Execute the Global<br />
mode page menu command “Load Preload/Demo<br />
Data” to load the data. ☞p.127<br />
Can’t operate the LCD screen correctly<br />
In Global P0: Basic Setup, execute the “Touch Panel<br />
Calibration” page menu command to adjust the<br />
sensitivity of the touch panel. ☞PG p.157<br />
If it is not possible to select this command from the<br />
page menu, enter Global mode P0 (press the [MENU]<br />
key, and then press the [0] or [EXIT] key to access<br />
this), and then hold down the [ENTER] key and press<br />
numeric key [3] to display the dialog box.<br />
Can’t switch modes or pages<br />
Are you recording or playing a song?<br />
Are you sampling?<br />
Are you playing a CD?<br />
Are you playing a WAVE file?<br />
Appendices<br />
In Combination, Sequencer, or Song Play modes, can’t edit<br />
the value of Timbre/Track parameters such as “MIDI<br />
Channel” or “Status”<br />
Some parameters cannot be edited during a “note-on”<br />
condition; i.e., while a note is held down on the<br />
keyboard, or while the damper pedal is held down.<br />
→ Are you using a damper pedal with a polarity that<br />
does not match the “Damper Polarity” setting (Global<br />
P2: Controller)?<br />
→ In some cases, this problem can be solved be executing<br />
the page menu command “Half Damper Calibration”<br />
(Global P0: Basic Setup).<br />
No beep is sounded when you touch the LCD screen<br />
Check the “Beep Enable” check box (Global P0: Basic<br />
Setup, System Preference). ☞p.90<br />
Audio input and output<br />
No sound<br />
Are connections made correctly to your amp, mixer, or<br />
headphones? ☞p.15<br />
Is the connected amp or mixer powered-on, and is its<br />
volume raised?<br />
Is Local Control turned on?<br />
→ In Global P1: MIDI, check the “Local Control On”<br />
check box. ☞PG p.161<br />
Is the [VOLUME] slider raised? ☞p.3<br />
If there is no sound from the OUTPUT (INDIVIDUAL)<br />
1–4 jacks, make sure that “BUS Select” or “BUS Select”<br />
following the insert effect is set to 1, 2, 3(Tube),<br />
4(Tube), 1/2, or 3/4(Tube). ☞p.104<br />
If specific tracks in Sequencer mode or Song Play<br />
mode do not sound, Make sure that the PLAY/<br />
MUTE/REC button or PLAY/MUTE button is set to<br />
PLAY. ☞p.42, 88<br />
Make sure that the “Status” is INT or BTH. ☞p.32, 41<br />
Are the Key Zone and Velocity Zone set so that sound<br />
will be produced when you play? ☞PG p.13, 47, 76<br />
Notes do not stop<br />
In Program P1: Edit Basic, select the Program Basic<br />
page, make sure that the “Hold” check box is<br />
unchecked. ☞PG p.10<br />
In Global P2: Controller, make sure that “Damper<br />
Polarity” or “Foot Switch Polarity” is set correctly.<br />
☞PG p.165<br />
Can’t input sound<br />
Are the appropriate sources connected to the AUDIO<br />
INPUT 1, 2 jacks, the S/P DIF IN jack? ☞p.64<br />
If there is no sound in Sampling mode, check that<br />
“Input,” “Level,” and “BUS (IFX/Indiv.) Select” are<br />
set correctly in the Sampling P0: Recording, Input/<br />
Setup page. ☞p.64<br />
131<br />
Program<br />
Combination<br />
Sequencer<br />
Sampling<br />
Song Play<br />
Global<br />
Effect<br />
Media, etc<br />
Preset<br />
Other<br />
Appendices