show voice port - Tecnológico de Costa Rica
show voice port - Tecnológico de Costa Rica show voice port - Tecnológico de Costa Rica
9 - 12 Aironet 340 Series Bridge Setting Screen Display Time (Display_Time) Use the display time option to set the Ethernet time interval for the automatic redisplay of any repeating display. The default value is 10 seconds. Determine Client IP Addresses (Ipadr) This function can be enabled to get the unit to determine the IP address of the client nodes associated to it. The address are then display in the Map function described above. If enabled the unit will watch traffic from the client associated to it and record the source IP addresses found.
Chapter 10 - Setting Up the Association Table CHAPTER 10 Setting Up the Association Table 10 This chapter describes the procedures for setting up the Association Table for the Aironet 340 Series Bridge. Here’s what you’ll find in this chapter: n Overview n Using the Association Menu n Displaying the Association Table n Displaying the Association Table Summary n Setting the Allowed Number of Child Nodes n Controlling Associations with Static Entries n Backbone LAN Node Stale Out Time n Specifying How Node Addresses are Displayed
- Page 361 and 362: Configuring the Radio Network 4 - 1
- Page 363 and 364: Viewing Errors (Errors) Configuring
- Page 365 and 366: Configuring the Radio Network 4 - 1
- Page 367 and 368: Roaming Notification Mode (Roaming)
- Page 369 and 370: Chapter 5 - Configuring the Etherne
- Page 371 and 372: Configuring the Ethernet Port 5 - 3
- Page 373 and 374: 6 - 2 Aironet 340 Series Bridge Usi
- Page 375 and 376: 6 - 4 Aironet 340 Series Bridge 2.
- Page 377 and 378: Chapter 7 - Configuring Mobile IP C
- Page 379 and 380: Configuring Mobile IP 7 - 3 On a fo
- Page 381 and 382: Configuring Mobile IP 7 - 5 work. T
- Page 383 and 384: Chapter 8 - Using the Spanning Tree
- Page 385 and 386: Understanding Loops Using the Spann
- Page 387 and 388: Using the Spanning-Tree Protocol 8
- Page 389 and 390: Establishing Timeouts Node Address
- Page 391 and 392: Using the Configuration STP Menu (R
- Page 393 and 394: Using the Spanning-Tree Protocol 8
- Page 395 and 396: Using the Spanning-Tree Protocol 8
- Page 397 and 398: Setting the Local Port Priority (Pr
- Page 399 and 400: Viewing the Port State (State) Usin
- Page 401 and 402: Chapter 9 - Viewing Statistics CHAP
- Page 403 and 404: Throughput Statistics (Throughput)
- Page 405 and 406: Error Statistics Viewing Statistics
- Page 407 and 408: Displaying Overall Status (Status)
- Page 409 and 410: Viewing Statistics 9 - 9 2. Type th
- Page 411: Displaying Node Information (Node)
- Page 415 and 416: Using the Association Menu Setting
- Page 417 and 418: Setting Up the Association Table 10
- Page 419 and 420: Setting Up the Association Table 10
- Page 421 and 422: Chapter 11 - Using Filters CHAPTER
- Page 423 and 424: Using Filters 11 - 3 n Both: Packet
- Page 425 and 426: Filtering Node Addresses (Node) Usi
- Page 427 and 428: Displaying the IP to Network Addres
- Page 429 and 430: Setting the Default Action (Default
- Page 431 and 432: Í To Add a Filter Using the Monito
- Page 433 and 434: If you type llc: a. When you select
- Page 435 and 436: Using Filters 11 - 15 The contents
- Page 437 and 438: Chapter 12 - Setting Up Event Logs
- Page 439 and 440: Setting Up Event Logs 12 - 3 Node
- Page 441 and 442: Error Logs Severe Error Logs “Cat
- Page 443 and 444: Lost our association, new specified
- Page 445 and 446: Setting Up Event Logs 12 - 9 NOTE:
- Page 447 and 448: Setting Statistic Parameters (Stati
- Page 449 and 450: The following trap messages will be
- Page 451 and 452: Chapter 13 - Performing Diagnostics
- Page 453 and 454: Performing Diagnostics 13 - 3 are d
- Page 455 and 456: Physically Locating a Unit (Find) P
- Page 457 and 458: Performing Diagnostics 13 - 7 4. Th
- Page 459 and 460: Performing Diagnostics 13 - 9 5. Se
- Page 461 and 462: Performing Diagnostics 13 - 11 4. I
9 - 12 Aironet 340 Series Bridge<br />
Setting Screen Display Time (Display_Time)<br />
Use the display time option to set the Ethernet time interval for the<br />
automatic redisplay of any repeating display. The <strong>de</strong>fault value is 10<br />
seconds.<br />
Determine Client IP Addresses (Ipadr)<br />
This function can be enabled to get the unit to <strong>de</strong>termine the IP address<br />
of the client no<strong>de</strong>s associated to it. The address are then display in the<br />
Map function <strong>de</strong>scribed above.<br />
If enabled the unit will watch traffic from the client associated to it and<br />
record the source IP addresses found.