show voice port - Tecnológico de Costa Rica

More documents

Recommendations

Info

Installing the Console Port Cable Installing the Aironet 340 Series Bridge 1 - 5 1. Attach the Console Port cable to the Serial Port. Attach the other cable end to the Serial Port on a terminal or a PC running a terminal emulation program. Use a 9-pin male to 9-pin female straight through cable (Figure 1.3). NOTE: This connection is required for setting up initial configuration information. After configuration is completed, this cable may be removed until additional configuration is required via the Serial Port. Figure 1.3 - Console Port Connection 2. Set the terminal to 9600 Baud, No-Parity, 8 data bits, 1 Stop bit, and ANSI compatible.
1 - 6 Aironet 340 Series Bridge Installing the Ethernet Connection The Aironet 340 Series Bridge sup<strong>port</strong>s three connection types: n 10Base2 (Thinnet) n 10Base5 (Thicknet) AUI connector n 10BaseT (Twisted Pair) Í To Attach 10Base2 (Thinnet) Cabling: 1. Make sure the unit is powered off. 2. Attach the Thinnet cabling to each end of a BNC T-connector, if applicable. 3. Attach the T-connector to the 10Base2 BNC (Figure 1.4). If the unit is at the end of the Ethernet cable, a 50-Ohm terminator must be installed on the open end of the T-connector. Figure 1.4 - Attaching 10Base2 (Thinnet) Cabling 10Base2 10Base5 10BaseT CAUTION: Removing a terminator to install extra cable, or breaking an existing cable to install a T-connector, will cause a disruption in Ethernet traffic. Consult with your LAN administrator before you change any Ethernet cabling connections.
Page 1 and 2:
Instituto Tecnológico de Costa Ric
Page 3 and 4:
AGRADECIMIENTO Agradezco a los Inge
Page 5 and 6:
Abstract The main objective of this
Page 7 and 8:
5.3 PROGRAMACIÓN DE LAS INTERFACES
Page 9 and 10:
FIGURA 6.5 GRÁFICO QUE MUESTRA LA
Page 11 and 12:
CAPÍTULO 1: INTRODUCCIÓN 11
Page 13 and 14:
El proyecto de graduación se reali
Page 15 and 16:
1.4 Objetivos Específicos 1. Reali
Page 17 and 18:
CAPÍTULO 2: ANTECEDENTES 17
Page 19 and 20:
La figura 2.1 muestra un diagrama d
Page 21 and 22:
SWITCH 0 SWITCH 1 SWITCH 2 SWITCH 7
Page 23 and 24:
2.3 Solución propuesta Se desea en
Page 25 and 26:
SWITCH 0 SWITCH 1 SWITCH 2 SWITCH 7
Page 27 and 28:
CAPÍTULO 3: PROCEDIMIENTO METODOL
Page 29 and 30:
3.3 Escoger diferentes métodos par
Page 31 and 32:
3.10 Distribución física Esta eta
Page 33 and 34:
Como ya se ha mencionado anteriorme
Page 35 and 36:
Del mismo modo, los router cuentan
Page 37 and 38:
Figura 4.3 Módulo serial de un pue
Page 39 and 40:
Figura 4.9 Tarjeta de Interfaz de v
Page 41 and 42:
Packeteer (Intelligent Bandwidth Ma
Page 43 and 44:
Sistema Global de Posicionamiento U
Page 45 and 46:
Figura 4.13 Vista frontal del GPS M
Page 47 and 48:
5.1 Configuración de voz sobre IP
Page 49 and 50:
El valor interfaz se reemplaza con
Page 51 and 52:
Figura 5.2 Segmentos de llamada vis
Page 53 and 54:
eq-qos [ best-effort | controlled-l
Page 55 and 56:
Los números de teléfono se pueden
Page 57 and 58:
El siguiente paso consiste en progr
Page 59 and 60:
Tabla 5.4 Descripción de los coman
Page 61 and 62:
5.5 Configuración de los puertos d
Page 63 and 64:
destino específico. “número1”
Page 65 and 66:
5.6 Configuración del Puente Inal
Page 67 and 68:
La figura 5.4 muestra una vista gen
Page 69 and 70:
Diagnostics: permite realizar prueb
Page 71 and 72:
Frequency: establece la frecuencia
Page 73 and 74:
CAPÍTULO 6: ANÁLISIS Y RESULTADOS
Page 75 and 76:
La figura 6.10 muestra un gráfico
Page 77 and 78:
Figura 6.3 Eficiencia de la red de
Page 79 and 80:
Figura 6.7 Gráfico que muestra la
Page 81 and 82:
Figura 6.11 Gráfico que muestra la
Page 83 and 84:
Unisys de Centroamérica desea tras
Page 85 and 86:
6.2.3 Segmentos de Red También se
Page 87 and 88:
hUNISYS : es la altura completa del
Page 89 and 90:
Figura 6.15 Diagrama de la ubicaci
Page 91 and 92:
La altura de 13.05 metros de la tor
Page 93 and 94:
CAPÍTULO 7: CONCLUSIONES Y RECOMEN
Page 95 and 96:
No se requiere que en Unisys de Cen
Page 97 and 98:
ANEXOS 98
Page 99 and 100:
ANEXOS 96
Page 101 and 102:
Configuring Voice Ports This chapte
Page 103 and 104:
Validation Tips Step Command Purpos
Page 105 and 106:
Step Command Purpose Configuring E&
Page 107 and 108:
Validation Tips Fine-Tuning E&M Voi
Page 109 and 110:
Activating the Voice Port Step Comm
Page 111 and 112:
• Activating the Voice Port Confi
Page 113 and 114:
Fine-Tuning FXO and FXS Voice Ports
Page 115 and 116:
Step Command Purpose Configuring E&
Page 117 and 118:
Page 119 and 120:
Step Command Purpose Fine-Tuning E&
Page 121 and 122:
Anexo 2: Configuración de VoIP en
Page 123 and 124:
2 Voice over IP Quick Start Guide
Page 125 and 126:
Installing Voice Network Modules an
Page 127 and 128:
Installing Voice Network Modules an
Page 129 and 130:
Voice Port Numbering Voice Port Num
Page 131 and 132:
Entering Configuration Mode Enterin
Page 133 and 134:
Configuring the IP Network for Real
Page 135 and 136:
Configuring the IP Network for Real
Page 137 and 138:
Configuring FXS Interfaces Configur
Page 139 and 140:
Configuring FXS Interfaces 18 Voice
Page 141 and 142:
Configuring FXS Interfaces Wild Car
Page 143 and 144:
Configuring FXS Interfaces 22 Voice
Page 145 and 146:
Configuring FXO Interfaces Configur
Page 147 and 148:
Configuring E&M Interfaces Configur
Page 149 and 150:
Configuring E&M Interfaces 28 Voice
Page 151 and 152:
List of Terms List of Terms This se
Page 153 and 154:
Cisco Connection Online Cisco Conne
Page 155 and 156:
CHAPTER Configuring Voice over IP f
Page 157 and 158:
Prerequisites Tasks Prerequisites T
Page 159 and 160:
Configuration Tasks To configure Vo
Page 161 and 162:
Configure RSVP for Voice Enable RSV
Page 163 and 164:
You should configure Multilink PPP
Page 165 and 166:
Enable RTP Header Compression on a
Page 167 and 168:
Frame Relay for Voice over IP Confi
Page 169 and 170:
Table 2-1 Sample Number Expansion T
Page 171 and 172:
Figure 2-5 Outgoing Calls from the
Page 173 and 174:
Configure POTS Peers To configure t
Page 175 and 176:
Configure VoIP Peers Verify Tips Co
Page 177 and 178:
• Call progress tone using the cp
Page 179 and 180:
Fine-Tune FXO and FXS Voice Ports T
Page 181 and 182:
Page 183 and 184:
Step Command Purpose Fine-Tune E&M
Page 185 and 186:
Configure CODEC and VAD for Dial Pe
Page 187 and 188:
Step 8 Click the Up button until th
Page 189 and 190:
Limit TCP Transactions Limit TCP Tr
Page 191 and 192:
Establish Queueing and Congestion S
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Modify the System Buffer Size To di
Page 199 and 200:
Performance Management Examples The
Page 201 and 202:
4-2 • output attenuation • port
Page 203 and 204:
Command Syntax Conventions Command
Page 205 and 206:
acc-qos 4-6 Example The following e
Page 207 and 208:
answer-address 4-8 Example The foll
Page 209 and 210:
comfort-noise comfort-noise 4-10 To
Page 211 and 212:
cptone cptone 4-12 To configure a v
Page 213 and 214:
description description To include
Page 215 and 216:
destination-pattern 4-16 Related Co
Page 217 and 218:
dial-peer voice dial-peer voice 4-1
Page 219 and 220:
echo-cancel coverage echo-cancel co
Page 221 and 222:
echo-cancel enable echo-cancel enab
Page 223 and 224:
fax-rate fax-rate 4-24 To establish
Page 225 and 226:
icpif icpif 4-26 To specify the Cal
Page 227 and 228:
input gain input gain To configure
Page 229 and 230:
ip udp checksum ip udp checksum 4-3
Page 231 and 232:
non-linear non-linear 4-32 To enabl
Page 233 and 234:
operation operation To select a spe
Page 235 and 236:
port port 4-36 To associate a dial
Page 237 and 238:
eq-qos req-qos 4-38 To specify the
Page 239 and 240:
ing number ring number To specify t
Page 241 and 242:
session target session target 4-42
Page 243 and 244:
show call active voice show call ac
Page 245 and 246:
show call active voice 4-46 Table 4
Page 247 and 248:
show call history voice show call h
Page 249 and 250:
show call history voice 4-50 Table
Page 251 and 252:
show dial-peer voice 4-52 The follo
Page 253 and 254:
show dialplan incall number show di
Page 255 and 256:
show num-exp show num-exp 4-56 To s
Page 257 and 258:
show voice port 4-58 Voice card spe
Page 259 and 260:
show voice port 4-60 Table 4-7 Show
Page 261 and 262:
shutdown (voice-port configuration)
Page 263 and 264:
signal 4-64 Note If you change the
Page 265 and 266:
snmp-server enable traps snmp-serve
Page 267 and 268:
snmp-server enable traps 4-68 The s
Page 269 and 270: timeouts initial timeouts initial 4
Page 271 and 272: timing clear-wait timing clear-wait
Page 273 and 274: timing delay-start timing delay-sta
Page 275 and 276: timing digit timing digit To specif
Page 277 and 278: timing pulse timing pulse To specif
Page 279 and 280: timing wink-duration timing wink-du
Page 281 and 282: type type 4-82 To specify the E&M i
Page 283 and 284: vad vad 4-84 To enable voice activi
Page 285 and 286: Anexo 4: Guía de antenas y accesor
Page 287 and 288: Table 26-15: Physical and Environme
Page 289 and 290: Software Ordering Information Softw
Page 291 and 292: Installation Notes Installation Not
Page 293 and 294: Anexo 5: Manual de usuario de los p
Page 295 and 296: THE SPECIFICATIONS AND INFORMATION
Page 297 and 298: Contents About the User’s Guide .
Page 299 and 300: Contents iii Setting the Forwarding
Page 301 and 302: Chapter 9 - Viewing Statistics Cont
Page 303 and 304: Appendix A -Aironet 340 Series Brid
Page 305 and 306: x Aironet 340 Series Bridge Chapter
Page 307 and 308: xii Aironet 340 Series Bridge Welco
Page 309 and 310: xiv Aironet 340 Series Bridge Radio
Page 311 and 312: xvi Aironet 340 Series Bridge Paren
Page 313 and 314: xviii Aironet 340 Series Bridge The
Page 315 and 316: Part 1 - Getting Started Part 1 - G
Page 317 and 318: 1 - 2 Aironet 340 Series Bridge Bef
Page 319: 1 - 4 Aironet 340 Series Bridge 2.
Page 323 and 324: 1 - 8 Aironet 340 Series Bridge Att
Page 325 and 326: 1 - 10 Aironet 340 Series Bridge Ty
Page 327 and 328: Chapter 2 - Accessing the Console S
Page 329 and 330: Sub-Menus Each menu contains the fo
Page 331 and 332: Accessing the Console System 2 - 5
Page 333 and 334: Web Access Accessing the Console Sy
Page 335 and 336: Accessing the Console System 2 - 9
Page 337 and 338: Using the Configuration Console Men
Page 339 and 340: Controlling SNMP access to the conf
Page 341 and 342: Setting the Communication Port Para
Page 343 and 344: Monitoring of the DTR Signal Access
Page 345 and 346: Chapter 3 - Before You Begin CHAPTE
Page 347 and 348: Before You Begin 3 - 3 Time: Used t
Page 349 and 350: Chapter 4 - Configuring the Radio N
Page 351 and 352: Using the Configuration Radio Menu
Page 353 and 354: Configuring the Radio Network 4 - 5
Page 357 and 358: Packet Encryption (Privacy Menu) Co
Page 363 and 364: Viewing Errors (Errors) Configuring
Page 367 and 368: Roaming Notification Mode (Roaming)
Page 369 and 370: Chapter 5 - Configuring the Etherne
Page 371 and 372:
Configuring the Ethernet Port 5 - 3
Page 373 and 374:
6 - 2 Aironet 340 Series Bridge Usi
Page 375 and 376:
6 - 4 Aironet 340 Series Bridge 2.
Page 377 and 378:
Chapter 7 - Configuring Mobile IP C
Page 379 and 380:
Configuring Mobile IP 7 - 3 On a fo
Page 381 and 382:
Configuring Mobile IP 7 - 5 work. T
Page 383 and 384:
Chapter 8 - Using the Spanning Tree
Page 385 and 386:
Understanding Loops Using the Spann
Page 387 and 388:
Using the Spanning-Tree Protocol 8
Page 389 and 390:
Establishing Timeouts Node Address
Page 391 and 392:
Using the Configuration STP Menu (R
Page 393 and 394:
Page 395 and 396:
Page 397 and 398:
Setting the Local Port Priority (Pr
Page 399 and 400:
Viewing the Port State (State) Usin
Page 401 and 402:
Chapter 9 - Viewing Statistics CHAP
Page 403 and 404:
Throughput Statistics (Throughput)
Page 405 and 406:
Error Statistics Viewing Statistics
Page 407 and 408:
Displaying Overall Status (Status)
Page 409 and 410:
Viewing Statistics 9 - 9 2. Type th
Page 411 and 412:
Displaying Node Information (Node)
Page 413 and 414:
Chapter 10 - Setting Up the Associa
Page 415 and 416:
Using the Association Menu Setting
Page 417 and 418:
Setting Up the Association Table 10
Page 419 and 420:
Setting Up the Association Table 10
Page 421 and 422:
Chapter 11 - Using Filters CHAPTER
Page 423 and 424:
Using Filters 11 - 3 n Both: Packet
Page 425 and 426:
Filtering Node Addresses (Node) Usi
Page 427 and 428:
Displaying the IP to Network Addres
Page 429 and 430:
Setting the Default Action (Default
Page 431 and 432:
Í To Add a Filter Using the Monito
Page 433 and 434:
If you type llc: a. When you select
Page 435 and 436:
Using Filters 11 - 15 The contents
Page 437 and 438:
Chapter 12 - Setting Up Event Logs
Page 439 and 440:
Setting Up Event Logs 12 - 3 Node
Page 441 and 442:
Error Logs Severe Error Logs “Cat
Page 443 and 444:
Lost our association, new specified
Page 445 and 446:
Setting Up Event Logs 12 - 9 NOTE:
Page 447 and 448:
Setting Statistic Parameters (Stati
Page 449 and 450:
The following trap messages will be
Page 451 and 452:
Chapter 13 - Performing Diagnostics
Page 453 and 454:
Performing Diagnostics 13 - 3 are d
Page 455 and 456:
Physically Locating a Unit (Find) P
Page 457 and 458:
Performing Diagnostics 13 - 7 4. Th
Page 459 and 460:
Performing Diagnostics 13 - 9 5. Se
Page 461 and 462:
Performing Diagnostics 13 - 11 4. I
Page 463 and 464:
Performing Diagnostics 13 - 13 If t
Page 465 and 466:
Appendix A - Aironet 340 Series Bri
Page 467 and 468:
Console Port Pin-Out The Console Po
Page 469 and 470:
B-2 Aironet 340 Series Bridge Conti
Page 471 and 472:
B-4 Aironet 340 Series Bridge Broad
Page 473 and 474:
B-6 Aironet 340 Series Bridge Desti
Page 475 and 476:
C-2 Aironet 340 Series Bridge The I
Page 477 and 478:
C-4 Aironet 340 Series Bridge The I
Page 479 and 480:
C-6 Aironet 340 Series Bridge The U
Page 481 and 482:
C-8 Aironet 340 Series Bridge The S
Page 483 and 484:
C-10 Aironet 340 Series Bridge MIBI
Page 485 and 486:
C-12 Aironet 340 Series Bridge The
Page 487 and 488:
Page 489 and 490:
Page 491 and 492:
Page 493 and 494:
Appendix E - Regulatory Information
Page 495 and 496:
Department of Communications—Cana
Page 497 and 498:
E-5
Page 499 and 500:
LATIN AMERICA AND CARIBBEAN GROUP G
Page 501:
LATIN AMERICA AND CARIBBEAN GROUP C
show all

show voice port - Tecnológico de Costa Rica

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?